Abstract:It is necessary to fabricate (RE)BCO bulk high temperature superconductors in the form of individual single grains in order to maximise the length scale over which current flows, and hence trapped magnetic field. However, inherent difficulties in the grain growth process place limitations on the diameter and height of the single grain that may be achieved by existing melt processes. A practical approach to increase the height of the sample and the trapped field at its surface is by assembling individual single grains in a stack formation with their ab planes aligned parallel, primarily to avoid the expensive process of fabricating large, individual monoliths. The trapped fields observed at the top and bottom surfaces of a single grain sample are frequently different since both the superconducting and physical properties of single grain (RE)BCO samples are generally non-uniform. This leads to challenges in determining how to arrange spatially stacks of single grain samples to generate the largest and most uniform trapped field overall. In this study we report the optimisation of two-stack configurations involving a total of 8 individual GdBCO/Ag single grains. The samples were arranged in four pairs and configured with different surfaces in contact in the assembly of the stack. The primary superconducting properties for trapped field and total flux applications were measured at 77 K and compared for each stack arrangement. The initial results indicate that surfaces with inferior flux trapping properties (measured in terms of the overall trapped field value) of a two-sample stack should be positioned at the middle of the assembly toachieve the best overall trapped field and higher total flux at the external, and therefore, usablesurface of the stack sample. A numerical modelling method that incorporates different Jc-Bcharacteristics for the top and bottom layers of a single grain to take account of the variability inphysical properties and spatial non-uniformity confirmed the optimised experimental arrangement of the stacked bulk samples. Furthermore, the optimisation of single grains of ring geometry to achieve a longer and wider uniform magnetic field zone inside the bore was also performed.

Optimisation of the processing parameters for the fabrication of high-quality joints between Y-Ba-Cu-O single grain, bulk superconductors

Microstructure of superconducting hetero-joints between single-grained Gd-Ba-Cu-O bulk superconductors

A reliable technique to fabricate superconducting joints between single grain, Y–Ba–Cu–O bulk superconductors

Fabrication of Nbti Superconducting Joint by Electromagnetic Forming Method

An Efficient Approach for Superconducting Joint of YBCO Coated Conductors

Development of persistent joints for superconducting Bi-2212 coils

Development of Electromagnetic Forming Nbti Superconducting Joint

Improvement of Superconducting Joint Properties for GdBa2Cu3Ox Bulk Superconductors Joined with ErBa2Cu3Ox Superconductor Using Local Melt-Growth Method

Design and optimization of low-resistance YBCO superconducting joint

Development of a persistent superconducting joint between Bi-2212/Ag-alloy multifilamentary round wires

Influence of A Novel Heat Treatment on Structures and Superconducting Properties of Ygdbco Coated Conductors

Low-resistance joints for YBCO-coated conductors with Ag nanoparticle paste

Optimisation of stacked, bulk high temperature superconductors for trapped-field magnet applications

Efficient Fabrication of Ultralight YBa<sub>2</sub>Cu<sub>3</sub>O<sub>7-</sub><i><sub>x</sub></i> Superconductors with Programmable Shape and Structure

A Novel Pre-Sintering Technique for the Growth of Y–Ba–Cu–O Superconducting Single Grains from Raw Metal Oxides

Efficient Fabrication of Ultralight YBa 2 Cu 3 O 7− x Superconductors with Programmable Shape and Structure

Fast joining of melt textured Y–Ba–Cu–O bulks with high quality

A combined powder melt and infiltration growth technique for fabricating nano-composited Y-Ba-Cu-O single-grain superconductor

Influence of soft ferromagnetic sections on the magnetic flux density profile of a large grain, bulk Y–Ba–Cu–O superconductor

Progress in superconducting joints

The Effect of Magnet Configurations on the Levitation Force of Melt Processed Ybco Bulk Superconductors