Abstract:The deformed mixed grains of the initial aged GH4169 superalloy need to be refined by annealing treatment. However, for the isothermal annealing treatment, the deformed mixed grains can only be refined to about 10 µm because the increase of nucleation rate needs to increase the temperature while the decrease of grain growth rate requires to decrease temperature. In the paper, an innovative method including an aging treatment and a subsequent continuous-cooling recrystallization annealing treatment (CC-RAT) is proposed. This method can not only increase the nucleation rate but decrease the grain growth rate. The effects of heat treatment parameters on microstructure are investigated. Besides, the grain refinement mechanism is studied using a developed cellular automaton (CA) model. The results show that the recrystallization takes place slowly during aging, while large number of δ precipitates appear. In subsequent CC-RAT, increasing starting temperature (T s), decreasing cooling rate (V) or ending temperature (T e) can remarkably promote recrystallization, thereby refining grain microstructure. This attributes to the increase of recrystallization nucleation rate and the effective control of grain growth rate. In the early stage of CC-RAT, δ precipitates hinder the quick growth of recrystallized grains nucleated firstly. Moreover, the increase of T s accelerates the nucleation rate, and the decrease of V prolongs the time for nucleation. Both of them promote the rapid formation of new recrystallized nuclei, especially at δ phase boundaries. As the annealing temperature decreases, newborn grains grow slowly, and these new grains restrict the growth of grains nucleated first. Therefore, a fine and uniform microstructure with an average grain size of 5.82 µm is obtained. However, when T s is too high or V is too low, some coarse recrystallized grains appear. Hence, the feasible process is concluded as follows: aging treatment (900 °C×12 h), followed by CC-RAT (T s = 990–1010 °C, V=1–2 °C/min, T e=950–970 °C).

Dually-refined grain and precipitate microstructure of ATF-FeCrAl alloy by a two-step annealing process to separate the recrystallization from precipitation

Influence of Cold-Rolling Reduction on Microstructure and Tensile Properties of Nuclear FeCrAl Alloy with Low Cr and Nb Contents

An innovative annealing treatment method and its mechanism to refine deformed mixed grains of initial aged GH4169 superalloy

Enhancing the Strength of AlCrFeNi HEAs Via Tailoring Aluminum Content and Optimal Aging Treatment

Ultra-fine-grained and gradient FeCrAl alloys with outstanding work hardening capability

Modification and refinement of Fe-containing phases, mechanical properties and strengthening mechanisms in Al–Fe alloys via Cr alloying and continuous rheo-extrusion

In-situ TEM investigation of defect evolution in FeCrAl during post-irradiation annealing

Designing Ultrastrong and Thermally Stable FeCrAl Alloys with the Fine-Grained Structure

Control of Laves Precipitation in a FeCrAl-based Alloy Through Severe Thermomechanical Processing

Concurrent Recrystallization and Precipitation for Combination of Superior Precipitation and Grain Boundary Hardening in Co37Cr20Ni37Ti3Al3 High-Entropy Alloy

Recrystallization and texture evolution of warm-pilgered FeCrAl alloy tube during annealing at 850°C

Effect of Annealing on Microstructure and Mechanical Properties of an Ultrafine-Structured Al-containing FeCoCrNiMn High-Entropy Alloy Produced by Severe Cold Rolling

Effect of Aging Time on Precipitates and Mechanical Properties of the Electron Beam Freeform Fabricated Ni-Fe-Cr Alloys Reinforced by Γ’ and TiC Phases

Tailoring the mechanical properties and thermal stability of additive manufactured micro-alloyed Al-Cu alloy via multi-stage heat treatment

Effect of Inter-Pass Annealing on the Deformation Microstructure of Ti-48Al-2Cr-2Nb Alloy

Mechanical property and strengthening mechanism of ZrC nanoparticle dispersion-strengthened Mo containing FeCrAl alloys

Annealing-induced multi-heterogeneous microstructure strengthening in FeCoCrNiMo 0.2 high-entropy alloys

Simultaneously enhance the tensile strength and ductility of dual-phase Fe37Ni36Cr10Al17 alloy via phase-selective recrystallization and aging

Mechanism of dynamic recrystallization of a FeCrAl alloy during hot compression

Enhanced strength-ductility combination by introducing bimodal grains structures in high-density oxide dispersion strengthened FeCrAl alloys fabricated by spark plasma sintering technology

Improving mechanical properties of an FCC high-entropy alloy by γ′ and B2 precipitates strengthening