Angioplasty standard of practice.

J. Spies,C. Bakal,D. Burke,J. Cardella,A. Drooz,M. E. Edwards,J. Husted,A. Palestrant,M. Pentecost,A. Roberts,W. Rogers,M. C. Spencer,P. J. Weyman

DOI: https://doi.org/10.1016/S1051-0443(92)72023-5

IF: 3.682

1992-05-01

Journal of Vascular and Interventional Radiology

Abstract:

What problem does this paper attempt to address?

Sub-100 ps coincidence time resolution for positron emission tomography with LSO:Ce codoped with Ca

Mythra Varun Nemallapudi,Stefan Gundacker,Paul Lecoq,Etiennette Auffray,Alessandro Ferri,Alberto Gola,Claudio Piemonte

DOI: https://doi.org/10.1088/0031-9155/60/12/4635

IF: 3.5

2015-05-28

Physics in Medicine and Biology

Abstract:The coincidence time resolution (CTR) becomes a key parameter of 511 keV gamma detection in time of flight positron emission tomography (TOF-PET). This is because additional information obtained through timing leads to a better noise suppression and therefore a better signal to noise ratio in the reconstructed image. In this paper we present the results of CTR measurements on two different SiPM technologies from FBK coupled to LSO:Ce codoped 0.4%Ca crystals. We compare the measurements performed at two separate test setups, i.e. at CERN and at FBK, showing that the obtained results agree within a few percent. We achieve a best CTR value of 85 ± 4 ps FWHM for 2 × 2 × 3 mm(3) LSO:Ce codoped 0.4%Ca crystals, thus breaking the 100 ps barrier with scintillators similar to LSO:Ce or LYSO:Ce. We also demonstrate that a CTR of 140 ± 5 ps can be achieved for longer 2 × 2 × 20 mm(3) crystals, which can readily be implemented in the current generation PET systems to achieve the desired increase in the signal to noise ratio.

engineering, biomedical,radiology, nuclear medicine & medical imaging
Nanocrystalline Lead Halide Perovskites to Boost Time‐of‐Flight Performance of Medical Imaging Detectors

Fiammetta Pagano,Jan Král,Kateřina Děcká,Marco Pizzichemi,Eva Mihóková,Václav Čuba,Etiennette Auffray

DOI: https://doi.org/10.1002/admi.202300659

IF: 5.4

2024-01-18

Advanced Materials Interfaces

Abstract:Cesium lead bromide thin films were deposited on GAGG, BGO, and LYSO to improve their timing performances. The time resolution of the resulting heterostructures was measured under X‐ray and 511 keV γ‐ray irradiation, achieving tenfold and twofold improvement over the standard scintillator in the two measurements respectively. This demonstrates great potential for time‐of‐flight X‐ray (TOF‐X‐ray) and positron emission tomography (TOF‐PET) applications. Time‐of‐flight (TOF) technique, traditionally used in high energy physics (HEP) and positron emission tomography (PET), is now being explored for lower energy applications like computed tomography (CT). Regardless of the application, pushing the current boundaries in time resolution calls for novel technologies and materials exhibiting ultra‐fast time response. Semiconductor nanocrystals like cesium lead halide perovskites (CsPbBr3), benefiting from quantum confinement effects, feature ultra‐fast decay and, when combined with a suitable bulk scintillator following a heterostructure concept, can also provide the necessary stopping power. In this work, thin films of CsPbBr3 on top of BGO, LYSO:Ce, and GAGG:Ce,Mg wafers are fabricated to test their impact on the single crystal scintillator time resolution under soft X‐rays excitation (about 10 keV). It is demonstrated that the CsPbBr3 layer significantly improves the overall time resolution in all cases, achieving up to a tenfold improvement with BGO and GAGG:Ce,Mg. Under 511 keV γ‐rays, a proof‐of‐concept of the heterostructure design for TOF‐PET using CsPbBr3 thin film deposited on GAGG:Ce,Mg bulk crystal is successfully tested. Shared events depositing energy in both materials are identified, resulting in more than twofold improved coincidence time resolution: 118 ± 4 ps full‐width‐at‐half‐maximum (FWHM) compared to the 272 ± 8 ps of solely GAGG:Ce,Mg.

materials science, multidisciplinary,chemistry
On timing-optimized SiPMs for Cherenkov detection to boost low cost time-of-flight PET

Stefan Gundacker,Giacomo Borghi,Simon R Cherry,Alberto Gola,Daehee Lee,Stefano Merzi,Michele Penna,Volkmar Schulz,Sun Il Kwon

DOI: https://doi.org/10.1088/1361-6560/ace8ee

2023-08-09

Abstract:Objective.Recent SiPM developments and improved front-end electronics have opened new doors in TOF-PET with a focus on prompt photon detection. For instance, the relatively high Cherenkov yield of bismuth-germanate (BGO) upon 511 keV gamma interaction has triggered a lot of interest, especially for its use in total body positron emission tomography (PET) scanners due to the crystal's relatively low material and production costs. However, the electronic readout and timing optimization of the SiPMs still poses many questions. Lab experiments have shown the prospect of Cherenkov detection, with coincidence time resolutions (CTRs) of 200 ps FWHM achieved with small pixels, but lack system integration due to an unacceptable high power uptake of the used amplifiers.Approach.Following recent studies the most practical circuits with lower power uptake (<30 mW) have been implemented and the CTR performance with BGO of newly developed SiPMs from Fondazione Bruno Kessler tested. These novel SiPMs are optimized for highest single photon time resolution (SPTR).Main results.We achieved a best CTR FWHM of 123 ps for 2 × 2 × 3 mm3and 243 ps for 3 × 3 × 20 mm3BGO crystals. We further show that with these devices a CTR of 106 ps is possible using commercially available 3 × 3 × 20 mm3LYSO:Ce,Mg crystals. To give an insight in the timing properties of these SiPMs, we measured the SPTR with black coated PbF2of 2 × 2 × 3 mm3size. We confirmed an SPTR of 68 ps FWHM published in literature for standard devices and show that the optimized SiPMs can improve this value to 42 ps. Pushing the SiPM bias and using 1 × 1 mm2area devices we measured an SPTR of 28 ps FWHM.Significance.We have shown that advancements in readout electronics and SiPMs can lead to improved CTR with Cherenkov emitting crystals. Enabling time-of-flight with BGO will trigger a high interest for its use in low-cost and total-body PET scanners. Furthermore, owing to the prompt nature of Cherenkov emission, future CTR improvements are conceivable, for which a low-power electronic implementation is indispensable. In an extended discussion we will give a roadmap to best timing with prompt photons.
Low power implementation of high frequency SiPM readout for Cherenkov and scintillation detectors in TOF-PET

Joshua W Cates,Woon-Seng Choong

DOI: https://doi.org/10.1088/1361-6560/ac8963

IF: 3.5

2022-08-14

Physics in Medicine and Biology

Abstract:State-of-the-art (SoA) electronic readout for silicon photomultiplier (SiPM)-based scintillation detectors that demonstrate experimental limits in achievable coincidence time resolution (CTR) leverage low noise, high frequency signal processing to facilitate a single photon time response that is near the limit of the SiPMs architecture. This readout strategy can optimally exploit fast luminescence and prompt photon populations, and promising measurements show detector concepts employing this readout can greatly advance PET detector CTR, relative to SoA in clinical systems (~200 ps FWHM). However, the technique employs power hungry components which make the electronics chain impractical for channel-dense TOF-PET detectors. We have developed and tested a low noise and high frequency readout circuit which is performant at low power and consists of discrete elements with small footprints, making it feasible for integration into TOF-PET detector prototypes. A 3x3 mm2 Broadcom SiPM with this readout chain exhibited sub-100 ps single photon time resolution (SPTR) at 10 mW of power consumption, with a minor performance degradation to 120±2 ps FWHM at 5 mW. CTR measurements with 3x3x20 mm 3 LYSO and fast LGSO scintillators demonstrated 127±3 ps and 113±2 ps FWHM at nominal power dissipation and 133±2 ps and 121±3 ps CTR at 5 mW. BGO crystals 3x3x20 mm 3 in size show 271±5 ps FWHM CTR (1174±14 ps FWTM) at optimal power dissipation and 289±8 ps (1296±33 ps FWTM) at 5 mW. The compact and low power readout topology that achieves this performance thereby offers a platform to greatly advance PET system CTR and also opportunities to provide high performance TOF-PET at reduced material cost.

engineering, biomedical,radiology, nuclear medicine & medical imaging
Evaluation of cerium doped lutetium oxyorthosilicate (LSO) scintillation crystals for PET

C. Melcher,M. Graham,K. Pentlow,J. Schweitzer,P. Shenderov,F. Daghighiam

DOI: https://doi.org/10.1109/NSSMIC.1992.301022

1992-10-25

Abstract:A new scintillation crystal, cerium-doped lutetium oxyorthosilicate (LSO), was recently discovered, with light intensity 75% of NaI(Tl), scintillation decay time of 12 ns (30%) and 42 ns (70%), effective Z of 66, and density of 7.4 g/cc. The fast decay time and scintillation light output of LSO are superior to those of bismuth germanate (BGO) for positron emission tomography (PET) and the stopping power of LSO for 511 keV photons is only slightly lower than that of BGO. The authors directly compared the detection characteristics relevant to PET applications of small crystals of LSO (2*2*10 mm) with those of BGO. The energy resolution at 511 keV was 12% FWHM for LSO and two to three times wider for BGO. The coincidence timing of two opposing crystals, using a position sensitive photomultiplier tube (PMT) (Hamamatsu R2486), were 1.4 ns FWHM for LSO and more than three times higher for BGO. Using a fast PMT (Hamamatsu R3177), coincidence timing for LSO yielded 0.46 ns FWHM. These crystals are being used to simulate a small-scale PET scanner and to investigate its imaging performance.<<ETX>>

Medicine,Materials Science,Physics
Timing limits of ultrafast cross-luminescence emission in CsZnCl-based crystals for TOF-CT and TOF-PET

Katrin Herweg,Daniel Rutstrom,Vanessa Nadig,Luis Stand,Charles L Melcher,Mariya Zhuravleva,Volkmar Schulz,Stefan Gundacker

DOI: https://doi.org/10.1186/s40658-024-00663-x

2024-07-09

Abstract:Background: Good timing resolution in medical imaging applications such as TOF-CT or TOF-PET can boost image quality or patient comfort significantly by reducing the influence of background noise. However, the timing resolution of state-of-the-art detectors in CT and PET are limited by their light emission process. Core-valence cross-luminescence is an alternative, but well-known compounds (e.g. BaF2) pose several problems for medical imaging applications, such as their emission wavelength in the deep UV. CsZnCl-based materials show promise to solve this issue, as they provide fast decay times of 1-2 ns and an emission wavelength around 300 nm. Results: In this work, we investigated two CsZnCl-compounds: Cs2ZnCl4 and Cs3ZnCl5. We validated the previously published decay times on a time-correlated single-photon counting setup with 1.786 ± 0.016 ns for Cs2ZnCl4 and 1.034 ± 0.013 ns for Cs3ZnCl5. The setup's high resolution enabled the discovery of an additional prompt emission component with a significant abundance of 98 ± 18 (Cs2ZnCl4) and 86 ± 14 (Cs3ZnCl5) photons/MeV energy deposit. In a PET coincidence experiment, we measured the best coincidence time resolution (CTR) of 62 ps (FWHM) for Cs2ZnCL4 coupled to FBK VUV SiPMs with silicon oil. To assess the CTR for lower energies, we filtered the energy along the Compton continuum and found a deteriorated CTR that seems to be mainly influenced by photon statistics. Furthermore, this study gave us a rough estimate of e.g. 150 ps (FWHM) CTR at 100 keV energy for Cs2ZnCL4. From measurements with high activity of 14 MBq to check for pile-up effects we assume that Cs2ZnCl4 is better suited for high-rate time-of-flight applications than lutetium-based oxides. Simulations demonstrated that the stopping power of Cs2ZnCl4 is lower than for LSO:Ce,Ca, meaning that a high amount of material would be needed for TOF-PET applications. However, the stopping power seems acceptable for applications in TOF-CT. Conclusions: The fast decay time, state-of-the-art CTR in benchtop experiments and high-rate suitability make CsZnCl materials a promising candidate for time-of-flight experiments. We consider especially TOF-CT a suitable application due to its relatively low X-ray energies (~ 100 keV) and the thusly acceptable stopping power of Cs2ZnCl4. Currently, further exploration of the prompt emission and its creation mechanism is planned, as well as investigating the light transport of Cs2ZnCl4 in longer crystals.
INVESTIGATION OF LSO SCINTILLATORS FOR HIGH-RESOLUTION PET DETECTORS

Huafeng Liu,Chao Bao,Mitsuo Watanabe,Takaji Yamashita

2000-01-01

Abstract:The high density,high light output,and sho rt decay time of LSO (lutetiumorthosilicate) make it an attractive scinti llator for positron emission tomography (PET) detector applications.The performa nce of the LSO crystal was evaluated in terms of applicability to radiation imag ing systems.A number of surface conditions were considered in order to obtain hi gher light output.The single LSO crystal coupled to a position-sensitive photom ultiplier (PS-PMT),R5900-00-C12,showed energy resolution of 15% for the 511 k eV full energy peak from 22　Na soure.The timing resolution was 0. 65ns for the same condition.The spatial resolution capability was demonstrated by imaging three LSO arrays finally.
Ionizing photon interactions modulate the optical properties of crystals with femtosecond scale temporal resolution

Li Tao,Ryan N Coffee,Diana Jeong,Craig S Levin

DOI: https://doi.org/10.1088/1361-6560/abd951

2021-02-12

Abstract:In this work, we continue our study of a new method for the detection of ionizing radiation with the potential for a dramatic improvement in coincidence time resolution (CTR) for time-of-flight positron emission tomography (ToF-PET) using the modulation of a material's optical properties instead of the scintillation mechanism. Our previous work has shown that for non-scintillation materials such as bismuth silicon oxide (BSO) and cadmium telluride (CdTe), their refractive index can be modulated by annihilation photon interactions. The ultrafast nature of this process however remains unexplored. The ionizing radiation-induced charge carriers alter the local band structure in these materials, thus changing the complex refractive index. This mechanism is routinely used at the linac coherent light source (LCLS) facility of the SLAC National Accelerator Laboratory to measure x-ray pulse arrival times with femtosecond scale resolution for photon energies between 0.5 and 10 keV. The method described here follows that example by using a frequency chirped visible continuum pulse to provide a monotonic wavelength-to-time mapping by which one can measure the time-dependent refractive index modulation. In addition, we describe an interference-based measurement setup that allows for significantly improved sensitivity while preserving a timing precision of approximately 10 fs (σ) when measuring the arrival time of below 10 keV x-ray pulses with yttrium aluminum garnet (YAG) crystal. The method is presented in the context of ToF-PET application with further discussions on the potential CTR achievable if a similar detection concept is adopted for detecting 511 keV photons. Semi-empirical analysis indicates that the predicted CTR achievable is on the order of 1 ps (FWHM).
Measurement of intrinsic rise times for various L(Y)SO and LuAG scintillators with a general study of prompt photons to achieve 10 ps in TOF-PET

Stefan Gundacker,Etiennette Auffray,Kristof Pauwels,Paul Lecoq

DOI: https://doi.org/10.1088/0031-9155/61/7/2802

IF: 3.5

2016-03-16

Physics in Medicine and Biology

Abstract:The coincidence time resolution (CTR) of scintillator based detectors commonly used in positron emission tomography is well known to be dependent on the scintillation decay time (τd) and the number of photons detected (n'), i.e. CTR proportional variant √τd/n'. However, it is still an open question to what extent the scintillation rise time (τr) and other fast or prompt photons, e.g. Cherenkov photons, at the beginning of the scintillation process influence the CTR. This paper presents measurements of the scintillation emission rate for different LSO type crystals, i.e. LSO:Ce, LYSO:Ce, LSO:Ce codoped Ca and LGSO:Ce. For the various LSO-type samples measured we find an average value of 70 ps for the scintillation rise time, although some crystals like LSO:Ce codoped Ca seem to have a much faster rise time in the order of 20 ps. Additional measurements for LuAG:Ce and LuAG:Pr show a rise time of 535 ps and 251 ps, respectively. For these crystals, prompt photons (Cherenkov) can be observed at the beginning of the scintillation event. Furthermore a significantly lower rise time value is observed when codoping with calcium. To quantitatively investigate the influence of the rise time to the time resolution we measured the CTR with the same L(Y)SO samples and compared the values to Monte Carlo simulations. Using the measured relative light yields, rise- and decay times of the scintillators we are able to quantitatively understand the measured CTRs in our simulations. Although the rise time is important to fully explain the CTR variation for the different samples tested we determined its influence on the CTR to be in the order of a few percent only. This result is surprising because, if only photonstatistics of the scintillation process is considered, the CTR would be proportional to the square root of the rise time. The unexpected small rise time influence on the CTR can be explained by the convolution of the scintillation rate with the single photon time resolution (SPTR) of the photodetector and the photon travel spread (PTS) in the crystal. The timing benefits of prompt photons at the beginning of the scintillation process (Cherenkov etc) are further studied, which leads to the conclusion that the scintillation rise time, SPTR and PTS have to be lowered simultaneously to fully profit from these fast photons in order to improve the CTR significantly.

engineering, biomedical,radiology, nuclear medicine & medical imaging
A Novel TOF-PET Detector Based on SiPM and Cherenkov Radiation

Xiao Liu,Tianpeng Xu,Yan Xia,Tianyu Ma,Yaqiang Liu

DOI: https://doi.org/10.1109/nssmic.2017.8532682

2017-01-01

Abstract:Time of flight (TOF) technology has been widely applied in modern positron emission tomography (PET) systems. In TOF-PET detector development, the decay time of scintillation crystal is one of the major limit to the timing resolution. Nowadays, low-luminosity photon detection even at single photon level has come into use, which allows the detection of low-output Cherenkov photons to be possible. These Cherenkov photons is created by the moving electrons, which is produced by the photoelectric effect or Compton scatter of the 511 keV gamma photons. Since Cherenkov photon can be detected earlier and provides nearly prompt response to gamma photons, Cherenkov TOF-PET detector has become a promising TOF-PET choice. In this study, we evaluate the feasibility of a Cherenkov TOF-PET detector setup based on PbF 2 crystal and SensL dual-output SiPM. We also investigate the factors which could influence the coincidence resolving time (CRT), including ambient temperature, SiPM over voltage, crystal size and crystal surface treatment.
Analog electro-optical readout of SiPMs achieves fast timing required for time-of-flight PET/MR

M F Bieniosek,C S Levin

DOI: https://doi.org/10.1088/0031-9155/60/9/3795

2015-05-07

Abstract:The design of combined positron emission tomography/magnetic resonance (PET/MR) systems presents a number of challenges to engineers, as it forces the PET system to acquire data in a space constrained environment that is sensitive to electro-magnetic interference and contains high static, radio frequency and gradient fields. In this work we validate fast timing performance of a PET scintillation detector using a potentially very compact, very low power, and MR compatible readout method in which analog silicon photomultipliers (SiPM) signals are transmitted optically away from the MR bore with little or even no additional readout electronics. This analog 'electro-optial' method could reduce the entire PET readout in the MR bore to two compact, low power components (SiPMs and lasers). Our experiments show fast timing performance from analog electro-optical readout with and without pre-amplification. With 3 mm × 3 mm × 20 mm lutetium-yttrium oxyorthosilicate (LYSO) crystals and Excelitas SiPMs the best two-sided fwhm coincident timing resolution achieved was 220 +/- 3 ps in electrical mode, 230 +/- 2 ps in electro-optical with preamp mode, and 253 +/- 2 ps in electro-optical without preamp mode. Timing measurements were also performed with Hamamatsu SiPMs and 3 mm × 3 mm × 5 mm crystals. In the future the timing degradation seen can be further reduced with lower laser noise or improvements SiPM rise time or gain.
Study of optical reflectors for a 100ps coincidence time resolution TOF-PET detector design

Andrea Gonzalez-Montoro,Shirin Pourashraf,Min Sun Lee,Joshua W Cates,Craig S Levin

DOI: https://doi.org/10.1088/2057-1976/ac240e

2021-09-15

Abstract:Positron Emission Tomography (PET) reconstructed image signal-to-noise ratio (SNR) can be improved by including the 511 keV photon pair coincidence time-of-flight (TOF) information. The degree of SNR improvement from this TOF capability depends on the coincidence time resolution (CTR) of the PET system, which is essentially the variation in photon arrival time differences over all coincident photon pairs detected for a point positron source placed at the system center. The CTR is determined by several factors including the intrinsic properties of the scintillation crystals and photodetectors, crystal-to-photodetector coupling configurations, reflective materials, and the electronic readout configuration scheme. The goal of the present work is to build a novel TOF-PET system with 100 picoseconds (ps) CTR, which provides an additional factor of 1.5–2.0 improvement in reconstructed image SNR compared to state-of-the-art TOF-PET systems which achieve 225–400 ps CTR. A critical parameter to understand is the optical reflector's influence on scintillation light collection and transit time variations to the photodetector. To study the effects of the reflector covering the scintillation crystal element on CTR, we have tested the performance of four different reflector materials: Enhanced Specular Reflector (ESR) –coupled with air or optical grease to the scintillator; Teflon tape; BaSO4 paint alone or mixed with epoxy; and TiO2 paint. For the experimental set-up, we made use of 3 × 3 × 10 mm3 fast-LGSO:Ce scintillation crystal elements coupled to an array of silicon photomultipliers (SiPMs) using a novel 'side-readout' configuration that has proven to have lower variations in scintillation light collection efficiency and transit time to the photodetector. Results: show CTR values of 102.0 ± 0.8, 100.2 ± 1.2, 97.3 ± 1.8 and 95.0 ± 1.0 ps full-width-half-maximum (FWHM) with non-calibrated energy resolutions of 10.2 ± 1.8, 9.9 ± 1.2, 7.9 ± 1.2, and 8.6 ± 1.7% FWHM for the Teflon, ESR (without grease), BaSO4 (without epoxy) and TiO2 paint treatments, respectively.
Advances in heterostructured scintillators: toward a new generation of detectors for TOF-PET

Fiammetta Pagano,Nicolaus Kratochwil,Matteo Salomoni,Marco Pizzichemi,Marco Paganoni,Etiennette Auffray

DOI: https://doi.org/10.1088/1361-6560/ac72ee

2022-06-29

Abstract:Objective.Time-of-flight-positron emission tomography would highly benefit from a coincidence time resolution (CTR) below 100 ps: improvement in image quality and patient workflow, and reduction of delivered dose are among them. This achievement proved to be quite challenging, and many approaches have been proposed and are being investigated for this scope. One of the most recent consists in combining different materials with complementary properties (e.g. high stopping power for 511 keVγ-ray and fast timing) in a so-calledheterostructure,metascintillatorormetapixel. By exploiting a mechanism of energy sharing between the two materials, it is possible to obtain a fraction of fast events which significantly improves the overall time resolution of the system.Approach.In this work, we present the progress on this innovative technology. After a simulation study using the Geant4 toolkit, aimed at understanding the optimal configuration in terms of energy sharing, we assembled four heterostructures with alternating plates of BGO and EJ232 plastic scintillator. We fabricated heterostructures of two different sizes (3 × 3 × 3 mm3and 3 × 3 × 15 mm3), each made up of plates with two different thicknesses of plastic plates. We compared the timing of these pixels with a standard bulk BGO crystal and a structure made of only BGO plates (layeredBGO).Main results.CTR values of 239 ± 12 ps and 197 ± 10 ps FWHM were obtained for the 15 mm long heterostructures with 100µm and 200µm thick EJ232 plates (both with 100µm thick BGO plates), compared to 271 ± 14 ps and 303 ± 15 ps CTR for bulk and layered BGO, respectively.Significance.Significant improvements in timing compared to standard bulk BGO were obtained for all the configurations tested. Moreover, for the long pixels, depth of interaction (DOI) collimated measurements were also performed, allowing to validate a simple model describing light transport inside the heterostructure.
Electronics method to advance the coincidence time resolution with bismuth germanate

Joshua W Cates,Craig S Levin

DOI: https://doi.org/10.1088/1361-6560/ab31e3

2019-09-05

Abstract:Exploiting the moderate Cherenkov yield from 511 keV photoelectric interactions in bismuth germanate (BGO) scintillators enables one to achieve a level of coincidence time resolution (CTR) appropriate for time-of-flight positron emission tomography (TOF-PET). For this approach, owing to the low number of promptly emitted light photons, single photon time resolution (SPTR) can have a stronger influence on achievable CTR. We have previously shown readout techniques that reduce effective device capacitance of large area silicon photomultipliers (SiPMs) can yield improvements in single photon response shape that minimize the influence of electronic noise on SPTR. With these techniques, sub-100 ps FWHM SPTR can be achieved with [Formula: see text] mm2 FBK near-ultra-violet high density (NUV-HD) SiPMs. These sensors are also useful for detecting Cherenkov light due to relatively high photon detection efficiency for UV light. In this work, we measured CTR for BGO crystals coupled to FBK NUV-HD SiPMs with a passive bootstrapping readout circuit that effectively reduces the SiPM device capacitance. A range of CTR values between 200 [Formula: see text] 3 and 277 [Formula: see text] 7 ps FWHM were measured for 3 [Formula: see text] 3 [Formula: see text] 3 and 3 [Formula: see text] 3 [Formula: see text] 15 mm3 crystals, respectively. This readout technique provides a relatively simple approach to achieve state-of-the-art CTR performance using BGO crystals for TOF-PET.
Towards time-of-flight PET with a semiconductor detector

Gerard Ariño-Estrada,Gregory S Mitchell,Sun Il Kwon,Junwei Du,Hadong Kim,Leonard J Cirignano,Kanai S Shah,Simon R Cherry

DOI: https://doi.org/10.1088/1361-6560/aaaa4e

IF: 3.5

2018-02-16

Physics in Medicine and Biology

Abstract:The feasibility of using Cerenkov light, generated by energetic electrons following 511 keV photon interactions in the semiconductor TlBr, to obtain fast timing information for positron emission tomography (PET) was evaluated. Due to its high refractive index, TlBr is a relatively good Cerenkov radiator and with its wide bandgap, has good optical transparency across most of the visible spectrum. Coupling an SiPM photodetector to a slab of TlBr (TlBr-SiPM) yielded a coincidence timing resolution of 620 ps FWHM between the TlBr-SiPM detector and a LFS reference detector. This value improved to 430 ps FWHM by applying a high pulse amplitude cut based on the TlBr-SiPM and reference detector signal amplitudes. These results are the best ever achieved with a semiconductor PET detector and already approach the performance required for time-of-flight. As TlBr has higher stopping power and better energy resolution than the conventional scintillation detectors currently used in PET scanners, a hybrid TlBr-SiPM detector with fast timing capability becomes an interesting option for further development.

engineering, biomedical,radiology, nuclear medicine & medical imaging
Optimization of Dual Mode Readout of Sensl SiPM for TOF PET Detectors

Tianpeng Xu,Shulin Yao,Si Chen,Qingyang Wei,Yaqiang Liu,Tianyu Ma

DOI: https://doi.org/10.1109/nssmic.2015.7581741

2015-01-01

Abstract:A novel silicon photomultipliers (SiPM) has been developed with both a standard and a fast output, aiming at providing good energy and timing performance simultaneously for time of flight (TOF) PET application. Optimal readout method of this SiPM is investigated in this study. The standard output can be taken from either anode terminal or cathode terminal and different dual readout mode has different impact on timing resolution of fast output. Three dual mode readout methods were evaluated and we found the optimized way was to readout the standard output on the cathode side with a small capacitance in parallel. This readout method can preserve good timing performance using relatively few electronic components. We developed a detector module by directly coupling a 16×16 LYSO crystal block to an 8×8 Sensl FC30035 SiPM array. Through multiplexing and summing scheme and charge division resistor network, 64 channels of fast output and 64 channels of standard output are reduced to one fast timing signal and four energy signals, making the detector highly compact and scalable. The performance of the detector module was evaluated. 16×16 LYSO crystals were well resolved in the flood image and the average energy resolution were 12.4% ± 0.8% at 511 KeV. The average coincidence resolving timing (CRT) of the block against a single LYSO crystal coupled to a FC30035 pixel were 286 ± 13 ps. The average block-to-block CRT were estimated to be 311 ps. The proposed dual readout design has demonstrated excellent timing performance for TOF PET detectors.
Effectiveness of three age estimation methods based on dental and skeletal development in a sample of young Brazilians.

Marcelo Afonso Machado,E. Daruge Júnior,Mário Marques Fernandes,I. F. P. Lima,G. Cericato,A. Franco,L. Paranhos

DOI: https://doi.org/10.1016/j.archoralbio.2017.10.014

IF: 2.64

Archives of Oral Biology

Abstract:
Performance evaluation of the FastIC readout ASIC with emphasis on Cherenkov emission in TOF-PET

Markus Piller,Antonio M Castilla,Giulia Terragni,Jerome Alozy,Etiennette Auffray,Rafael Ballabriga,Michael Campbell,Bernd Deutschmann,David Gascon,Alberto Gola,Stefano Merzi,Alicja Michalowska-Forsyth,Michele Penna,Sergio Gómez Fernández,Nicolaus Kratochwil

DOI: https://doi.org/10.1088/1361-6560/ad42fe

IF: 3.5

2024-04-25

Physics in Medicine and Biology

Abstract:Objective. The efficient usage of prompt photons like Cherenkov emission is of great interest for the design of the next generation, cost-effective, and ultrahigh-sensitivity TOF-PET scanners. With custom, high power consuming, readout electronics and fast digitization the prospect of sub-300 ps FWHM with PET-sized BGO crystals have been shown. However, these results are not scalable to a full system consisting of thousands of detector elements. Approach. To pave the way toward a full TOF-PET scanner, we examine the performance of the FastIC ASIC with Cherenkov-emitting scintillators (BGO), together with one of the most recent SiPM detector developments based on metal trenching from FBK. The FastIC is a highly configurable ASIC with 8 input channels, a power consumption of 12 mW/ch and excellent linearity on the energy measurement. To put the timing performance of the FastIC into perspective, comparison measurements with high-power consuming readout electronics are performed. Main results. We achieve a best CTR FWHM of 330 ps for 2x2x3 mm3 and 490 ps for 2x2x20 mm3 BGO crystals with the FastIC. In addition, using 20 mm long LSO:CeCa crystals, CTR values of 129 ps FWHM have been measured with the FastIC, only slightly worse to the state-of-the-art of 95 ps obtained with discrete HF electronics. Significance. For the first time, the timing capability of BGO with a scalable ASIC has been evaluated. The findings underscore the potential of the FastIC ASIC in the development of cost-effective TOF-PET scanners with excellent timing characteristics.

engineering, biomedical,radiology, nuclear medicine & medical imaging
Characterization of TOF-PET Detectors Based on Monolithic Blocks and ASIC-Readout

Efthymios Lamprou,Andrea Gonzalez-Montoro,Gabriel Canizares,Victor Ilisie,John Barrio,Filomeno Sanchez,Antonio J. Gonzalez,Jose Maria Benlloch

DOI: https://doi.org/10.48550/arXiv.1806.08715

2018-06-22

Abstract:The aim of this work is to show the potential capabilities of monolithic crystals coupled to large SiPM arrays, to be considered as detector blocks for PET scanners enabling Time Of Flight (TOF) capabilities. Monolithic blocks allow one to decode the 3D photon impact position. This approach, along with TOF information, can be of high interest in clinical Positron emission tomography (PET) applications where a typical ring configuration is used. In this manuscript, we evaluate an ASIC- based readout for digitizing all signals coming from analog photosensors. Validation results with one-to-one coupling resulted in a Coincidence Time Resolution (CTR) of 202 ps FWHM. Providing timing resolution when using detectors based on monolithic crystals is however challenging. The wide distribution of scintillation light on the photosensors causes a poor SNR, which makes the system sensible to false triggering and to time walk errors. In this direction, we present a calibration method, designed to correct all recorded timestamps and also to compensate variations in time-paths among all channels. Thereafter, a CTR improvement nearing 45% is observed for all measurements. Moreover, we show a novel approach that describes the use of averaging methods to assign a single timestamp to each gamma impact. This approach results in a further improvement of the CTR in the range of 100 ps FWHM, reaching a time resolution of 585 ps FWHM when using a large 50x50x10 mm3 LYSO scintillator coupled to an 8x8 SiPM (6x6 mm2) array. These pilot studies show detector capabilities regarding TOF information when using monolithic scintillators.

Instrumentation and Detectors
Investigation of the Time Performance of a LYSO Array for TOF-PET

Liu Jun-Hui,Xu Jiong-Hui,Cheng Feng-Feng,Li Dao-Wu,Zhang Zhi-Ming,Wang Bao-Yi,Wei Long

DOI: https://doi.org/10.48550/arXiv.1507.04429

2015-07-16

Abstract:Positron Emission Tomography (PET) using time-of-flight information, which can greatly improve the quality of the reconstructed image, has recently become an exciting topic. In this work, 3.2mm*3.2mm*25mm finger-like LYSO crystals were used to make a 5*5 array, coupled to the Hamamatsu H8500 photomultiplier tube (PMT) as a detector. A fast leading-edge discriminator was designed for the LYSO-H8500 detector. Average coincidence time resolution FWHM of 330 ps was obtained for the LYSO detector with a reference BaF2 detector, whose time resolution for 511 keV {\gamma}-rays was FWHM 150 ps. Time resolution FWHM of 294 ps was calculated for the LYSO detector, and coincidence time resolution of FHWM 415 ps can be expected for two identical LYSO detectors.

Instrumentation and Detectors

Angioplasty standard of practice.

Sub-100 ps coincidence time resolution for positron emission tomography with LSO:Ce codoped with Ca

Nanocrystalline Lead Halide Perovskites to Boost Time‐of‐Flight Performance of Medical Imaging Detectors

On timing-optimized SiPMs for Cherenkov detection to boost low cost time-of-flight PET

Low power implementation of high frequency SiPM readout for Cherenkov and scintillation detectors in TOF-PET

Evaluation of cerium doped lutetium oxyorthosilicate (LSO) scintillation crystals for PET

Timing limits of ultrafast cross-luminescence emission in CsZnCl-based crystals for TOF-CT and TOF-PET

INVESTIGATION OF LSO SCINTILLATORS FOR HIGH-RESOLUTION PET DETECTORS

Ionizing photon interactions modulate the optical properties of crystals with femtosecond scale temporal resolution

Measurement of intrinsic rise times for various L(Y)SO and LuAG scintillators with a general study of prompt photons to achieve 10 ps in TOF-PET

A Novel TOF-PET Detector Based on SiPM and Cherenkov Radiation

Analog electro-optical readout of SiPMs achieves fast timing required for time-of-flight PET/MR

Study of optical reflectors for a 100ps coincidence time resolution TOF-PET detector design

Advances in heterostructured scintillators: toward a new generation of detectors for TOF-PET

Electronics method to advance the coincidence time resolution with bismuth germanate

Towards time-of-flight PET with a semiconductor detector

Optimization of Dual Mode Readout of Sensl SiPM for TOF PET Detectors

Effectiveness of three age estimation methods based on dental and skeletal development in a sample of young Brazilians.

Performance evaluation of the FastIC readout ASIC with emphasis on Cherenkov emission in TOF-PET

Characterization of TOF-PET Detectors Based on Monolithic Blocks and ASIC-Readout

Investigation of the Time Performance of a LYSO Array for TOF-PET