Deformation Behaviour of Crushed Waste Rock under Lateral Cyclic Loading
Li Meng,Zhang Jixiong,Huang Peng,Sun Qiang,Yan Hao
DOI: https://doi.org/10.1007/s00603-021-02607-8
IF: 6.518
2021-01-01
Rock Mechanics and Rock Engineering
Abstract:Gangue (waste rock) is a kind of solid waste generated in coal mining, entry excavation and coal preparation (Du et al. 2019; Mohammadi et al. 2019; Xiao et al. 2020), and its discharge amount normally accounts for about 15% of coal production. Conventionally, gangue is transported to the surface and piled into a gangue hill, which usually induces the landslide or explosion hazard and causes serious damage to the ecological environment of the mining area (Adibee et al. 2013; Ju et al. 2019; Lappi and Ollikainen 2019; Xue et al. 2014). Besides, the roof above the coal seam loses its load-bearing capacity due to the extraction of the coal resource (Li et al. 2021; Xue et al. 2021). The roof mass subsides, fractures and caves due to its self-weight and the overburden stress. This strata movement gradually propagates to the overburden strata and finally leads to surface subsidence, soil and water loss, plant death and building collapses (Peng 2008; Zhang et al. 2019a, b, c). Therefore, many researchers proposed the concept of backfilling the mining goaf with crushed gangue in order to effectively eliminate the geological hazards and eco-environmental problems associated with mass mining and gangue accumulation (Guo et al. 2014; Junker and Witthaus 2013; Zhang et al. 2017a, b). However, the gangue backfilling material needs better compression performance with the increase of the mining depth and the in situ stress. It is of great necessity to improve the compactness of the gangue backfilling material. When the crushed gangue materials are filled into the coal mine goaf, the top part and the bottom part of the gangue backfilling material are surrounded by the roof and the floor, respectively, in the backfilling mining process. And because the crushed gangue materials are belonging to the porous medium, if we want to reduce the compressive deformation of gangue materials under the action of overlying strata, a certain lateral stress can be applied. Then the non-deformability of the gangue backfilling material can be improved by applying the lateral cyclic loading. Therefore, it is very important to study the deformation behaviour of crushed waste rock under lateral cyclic loading for effectively controlling the overlying strata movement and surface subsidence. The compressive characteristics of crushed gangue have been widely studied by laboratory experiments and numerical modelling (Li et al. 2020; Sreenivasa et al. 2020; Suchowerska et al. 2013; Weng et al. 2019; Wu et al. 2018; Yavuz 2004; Zhang et al. 2019a, b, c). Pappas and Mark (1993) investigated the mechanical characteristics of the rock fragmentations in the mining goaf and revealed the relation among the tangent modulus, the secant modulus and the compressive stress in the compression process. The stress–strain relation was described, using the formula given by Salamon and Terzaghi. Zhang et al. (2005) derived the relation among the compressive modulus, the axial stress and the axial strain based on compression test results and proposed the empirical formulae relating the compressive modulus, the strength of the rock fragmentation and porosity. Li et al. (2018) implemented an experimental approach to investigate the particle-crushing characteristics and acoustic emission characteristics of crushed gangue backfilling material during axial cyclic loading, which established the relationship between particle crushing and acoustic emission signals. At the same time, the relationship between particle crushing and AE signals was established. Yadav et al. (2020) expressed the stress–strain relation of the caved rock by the Salamon’s formula and found a numerical method simulating the compression process of the caved rocks in the mining * Jixiong Zhang cumtzjxiong@163.com