Abstract:PurposeAccurate 2D profile measurements at submillimeter precision are necessary for proton beam commissioning and periodic quality assurance (QA) purposes and are currently performed at our institution with a commercial scintillation detector (Lynx PT) with limited means for independent checks. The purpose of this work is to create an independent dosimetry system consisting of an in-house optical scanner and a BaFBrI:Eu2+ storage phosphor dosimeter by: (a) determining the optimal settings for the optical scanner, (b) measuring 2D proton spot profiles with the storage phosphors and (c) comparing them to similar measurements using a commercial scintillation detector. MethodsAn in-house two-dimensional (2D) laboratory optical scanner was constructed and spatially calibrated for accurate 2D photostimulated luminescence (PSL) dosimetry. Square 5 x 5 cm2 BaFBrI:Eu2+ dosimeter samples were uniformly irradiated with line scans performed to determine the physical and electronic scanner settings resulting in the highest signal-to-noise ratios (SNR) at a sub-millimeter spatial resolution. The resultant spatial resolution of the scanner was then quantitatively assessed by measuring (a) line pairs on a standard x-ray lead bar phantom and (b) modulation transfer functions. Following this, 2D proton spot profiles from a Mevion S250i Hyperscan proton unit were obtained at 1, 10, 20, 30, 40 and 50 monitor unit (MU) settings at maximum energy (E0 = 227.1 MeV) and compared to baseline profiles from a commercial scintillation detector, where 1 MU is calibrated to deliver 1 Gy absolute proton dose-to-water under reference conditions, i.e. 41 × 41 proton spots uniformly spaced by 0.25 cm within a 10 × 10 cm2 square field size at maximum energy (227.1 MeV) in water at depth of 5 cm at isocenter. The dosimetric system's sensitivities to (a) ±1 mm positional shifts and (b) ±0.3 mm beam lateral spread changes were quantitatively evaluated through a Gaussian fitting of the crossline and inline plots of the respective artificially shifted beam profiles. ResultsThe physical scanner settings of (a) Δτ = 27 ms time interval between data samples, (b) vx = 1.235 cm/s scanning speed, (c) 1% laser transmission (0.02 mW power) and (d) (Δx, Δy) = (0.33 mm, 0.50 mm) pixel sizes with electronic settings of (a) 300 microseconds time constant, (b) normal dynamic reserve, (c) 24 dB/oct low pass filter slope and (d) 160 Hz chopping frequency resulted in the highest SNR while maintaining sub-millimeter spatial resolution. The BaFBr0.85I0.15:Eu2+ storage phosphor dosimeters were linear from 1 – 50 MU and their profiles did not saturate up to 150 MU. The scanner was able to detect lateral displacements of ±1 mm in both the crossline and inline directions and ±0.3 mm beam spread changes that were artificially introduced by varying the incident proton energy. Specific to our proton unit, proton energy changes of ±1 MeV can also be detected indirectly via beam spread measurements. ConclusionOur combined dosimetric system including an in-house laboratory optical scanner and reusable BaFBr0.85I0.15:Eu2+ storage phosphors demonstrated a sufficient spatial resolution and dosimetric accuracy to support its use as an independent proton spot measurement dosimeter system. Its wide dynamic range allows for other versatile applications such as proton halo measurements.

Implementation of Sphinx/Lynx as daily QA equipment for scanned proton and carbon ion beams

Repurposing DailyQA3 for an efficient and spot position sensitive daily quality assurance tool for proton therapy

Evaluation of a prototype array for daily quality assurance in spot scanning proton therapy

Commissioning and clinical implementation of an independent dose calculation system for scanned proton beams

Dosimetric commissioning and quality assurance of scanned ion beams at the Italian National Center for Oncological Hadrontherapy

Implementation of novel measurement-based patient-specific QA for pencil beam scanning proton FLASH radiotherapy

Characterization of pixelated silicon detectors for daily quality assurance measurements in proton therapy

Development of a three-dimensional scintillation detector for pencil beam verification in proton therapy patient-specific quality assurance

Proton 3D dose measurement with a multi-layer strip ionization chamber (MLSIC) device

An integrated system for measuring 3D dose distributions of carbon-ion pencil beams in regular QA practice

Feasibility of using a transmission ion chamber for QA tests of medical linear accelerators

Significant acceleration of development by automating quality assurance of a medical particle accelerator safety system using a formal language driven test stand

A comprehensive pre‐clinical treatment quality assurance program using unique spot patterns for proton pencil beam scanning FLASH radiotherapy

Performance of a Scintillation Imaging System for Relative Dosimetry in Pencil Beam Scanning Proton Therapy

Proton-counting radiography for proton therapy: a proof of principle using CMOS APS technology

Development of a storage phosphor imaging system for proton pencil beam spot profile determination

Spread-out Bragg peak measurements using a compact quality assurance range calorimeter at the Clatterbridge Cancer Centre

A Multi-Layer Strip Ionization Chamber (MLSIC) Device for Proton Pencil Beam Scan Quality Assurance.

Dose-Area Product Determination and Beam Monitor Calibration for the Fixed Beam of the Shanghai Advanced Proton Therapy Facility

Characterization and performances of a monitoring ionization chamber dedicated to IBA-universal irradiation head for Pencil Beam Scanning

Implementation of an ionization chamber array for linear accelerator monthly dosimetry QA