Re-evaluating lipotoxic triggers in skeletal muscle: relating intramyocellular lipid metabolism to insulin sensitivity.

M. Bosma,S. Kersten,M. Hesselink,P. Schrauwen

DOI: https://doi.org/10.1016/j.plipres.2011.11.003

IF: 14.673

Progress in Lipid Research

Abstract:

What problem does this paper attempt to address?

Self-driving linear ultrasonic motor with double vibrators

鹿存跃,魏燕定,郭吉丰,胡金云,黎金良

DOI: https://doi.org/10.3785/j.issn.1008-973X.2009.08.022

2009-01-01

Abstract:A self-driving linear ultrasonic motor with double vibrators was developed. The stator consists of two vibrators and a mass. The mass is in the middle of the stator. Each vibrator is symmetrically connected with one side of the mass by a slender shaft. The bending vibrations of two vibrators inspire a wobbling motion of the mass. Therefore, the locus of particles on the driving head is an ellipse. The friction force between the mass and the leader drives the motor moving itself. The measured local bending resonant frequency of the mass is about 20 792 Hz, and that of the stator is about 40 420 Hz. Emulation results showed that when the local bending resonant mode of the mass is used as working mode, the vibration amplitude of the mass is large. Experimental results showed that the driving speed of the motor is high and the motor can work stably with little temperature rise when the mass working in the local bending resonant mode. But when the bending resonant mode of the stator is used as working mode, the temperature rise of the stator is high, therefore the motor cannot work stably. The characteristics of the prototype motor were measured experimentally. The maximum speed of the motor is about 598 mm/s, and the maximum driving force is over 1.94 N, when the phase difference of the applied two signals is 90° and the peak to peak driving voltage is 138 V at the frequency of 20.8 kHz.
Standing Wave-Type Bi-Directional Linear Moving Ultrasonic Motor Using Plates and Weak Links

Bo Wang,J. Y. Dai,Jifeng Guo

DOI: https://doi.org/10.1117/12.779873

2007-01-01

Abstract:A new trial of standing wave type bi-directional moving linear ultrasonic motor has been studied in this paper. Finite element modeling analysis revealed that by connecting three rectangular metal plates in different lengths together by two weak links, two bending vibration mode standing waves, i.e., one in sine wave and the other one in cosine wave, with nearly the same wavelength can be formed in the middle plate. With four pieces of PZT-4 piezoceramics mounted to the middle plates as driving elements, a new type of bi-directional linear moving ultrasonic motor of 60mm in length and 10mm in width has been designed, fabricated and characterized. The following performances have been achieved: maximum velocity 220nim/s, maximum output force 180gf, and resolution better than 0.2 mu m.
A linear ultrasonic motor with a hollowed and symmetrical stator

Jing Li,Fang Che,Jie Deng,Weishan Chen,Junkao Liu,Yingxiang Liu

DOI: https://doi.org/10.1016/j.ijmecsci.2023.108718

IF: 7.3

2023-09-13

International Journal of Mechanical Sciences

Abstract:A linear standing-wave ultrasonic motor with a hollowed and symmetrical stator is proposed in this study. The stator is cut from a cuboid block to produce a hollow and symmetrical structure, in which four thin-walled beams are formed on each end of the stator. Four driving feet are circumferentially installed at each end of the stator to guide the movement of the mover, and this design can simplify the guide rail and preload mechanism, which is beneficial to realize further miniaturization. Besides, the bi-directional motions are separately achieved by only using one sine signal to excite the same order vibration of the two groups of the thin-walled beams, which is conducive to the characteristic consistency of the bi-directional motions. Then, the finite element method is used to determine the parameters of the motor, the prototype is fabricated, and the output characteristics are tested. The experimental results show that the maximum no-load velocity, resolution, and maximum carrying load of the prototype in the forward motion were 30.86 mm/s, 0.5 μm and 39 mN, respectively; while that in the backward motion were 32.31 mm/s, 0.7 μm and 33 mN, respectively. This work sheds a new light on the design of the linear bi-directional standing-wave ultrasonic motors, simplifying the guide rail and preload mechanism and utilizing only one signal and the same order vibration to realize the bi-directional motions.

engineering, mechanical,mechanics
Development of a Radial-Torsional Vibration Hybrid Type Ultrasonic Motor with a Hollow and Short Cylindrical Structure

Jian Wang,Jifeng Guo

DOI: https://doi.org/10.1109/tuffc.2009.1138

IF: 3.267

2009-01-01

IEEE Transactions on Ultrasonics Ferroelectrics and Frequency Control

Abstract:A longitudinal-torsional hybrid-type ultrasonic motor has larger torque and lower revolution speed compared with other kinds of ultrasonic motors. It drives devices directly and precisely, so it is adaptable to many fields, especially aeronautics and astronautics, as a servo actuator. Due to the different sound propagation speeds of longitudinal and torsional vibrations in the stator, it is difficult to match resonant frequencies of longitudinal and torsional vibrations. In this paper, a new radial-torsional vibration hybrid-type ultrasonic motor is put forward, which utilizes longitudinal vibration derived from radial vibration by the Poisson effect. The short, hollow cylindrical structure easily makes resonant frequencies of first-order radial and torsional vibrations into degeneracy. First, the new structure of the motor is presented. Second, the principle of matching the resonant frequencies is developed, and the motor geometry is optimized by ANSYS software. Finally, a 60-mm diameter prototype is fabricated, which performs well. The no-load velocity and maximum torque are 25 r/min and 5 N.m, respectively. This kind of motor is small, light, and noiseless.
Design and Dynamic Simulation of a Novel Traveling Wave Linear Ultrasonic Motor

Lin Yang,Kaixi Yao,Weihao Ren,Liang Chen,Mojian Yang,Rongcheng Zhao,Siyu Tang

DOI: https://doi.org/10.3390/mi13040557

IF: 3.4

2022-03-31

Micromachines

Abstract:To overcome the problem of frequency consistency and simplify the design process of linear ultrasonic motor, a novel traveling wave linear ultrasonic motor with a ring-type stator is proposed in this paper. The combination of two orthogonal bending vibration modes with the same order is selected as the operating mode of the motor. A traveling wave along the side of the stator is utilized to drive the slider to move linearly. The stator adopts a ring symmetrical structure, which can effectively ensure that the resonance frequencies of the two vibration modes are consistent. Thus, we do not need to tune the frequencies of the two vibrations by constantly adjusting the shape of the stator or designing complex clamping parts to fix the stator without making any influence on the vibrations. Meanwhile, a three-dimensional finite element model of the motor is built. Using the model, we obtain the elliptical motion trajectories of the stator driving surface, the output performance of the motor, the sticking-slipping-separation contact characteristic between the stator and the slider and fabricate and measure a prototype of the proposed motor.

chemistry, analytical,nanoscience & nanotechnology,instruments & instrumentation,physics, applied
A Hollow Cylindrical Linear Nut-Type Ultrasonic Motor

Chen Zhuzi,Chen Yu,Zhou Tieying

DOI: https://doi.org/10.5755/j01.mech.22.6.13366

2017-01-01

Mechanika

Abstract:A hollow, linear, nut-type, ultrasonic motor based on two degenerate, 3rd-order bending modes in the section plane of cylinders is presented in this paper. The stator and rotor of the motor are both cylindrical and hollow, making the motor appropriate for applications where a light path, electric wire or optic fiber is required to pass through the motor. A new structure with four PZT plates bonded on the stator is proposed here. and the other had all eight sides bonded with PZT plates. The results show that the new design with four PZT plates has a higher mechanical quality factor, vibrates with larger amplitude, and has comparable performance to the stator with eight PZT plates. The motor with four PZT plates reached an upward speed of 0.95 mm/s when the load force was 3 g, and the maximum thrust force was 0.35 N.Two stators were fabricated and studied.
Localization effects of acetylcholine release from a synaptic vesicle at the neuromuscular junction.

T. Naka,N. Sakamoto

DOI: https://doi.org/10.1016/S0303-2647(99)00021-0

IF: 1.957

1999-08-01

Biosystems

Abstract:
Modeling and tests for a stator of a traveling-wave type spherical ultrasonic motor with 2-DOF

Ping FU,Run-jie SHEN,Guang-ju SHUAI,Ji-feng GUO,Xi-xing HU

DOI: https://doi.org/10.3969/j.issn.1000-3835.2013.14.003

2013-01-01

Abstract:A 2-DOF spherical traveling wave type ultrasonic motor is a kind of multi-DOF ultrasonic motors. The driving principle and basic structure of this kind of spherical ultrasonic motor were firstly introduced. Then, some basic problems of the motor were presented and the structure of the motor, the optimal structure of its stator and the tuning devices were explained. The stator with a big rake angle on its outer edge, a small rake angle on its inner edge and the tuning method of adjusting rake angles on its outer edge were presented. The contact model of the stator was built for calculation of its mechanical characteristics. Simulation and test results were verified each other for the stator. It was shown that the rotor diameter of the prototype motor is 45 mm and the stator diameter is 30mm, the maximum output torque is 120 mNm, the maximum rotating speed is 12 r/min. The results provided a foundation for design theory and performance improvement of a 2-DOF spherical traveling wave type ultrasonic motor.
A two-DOF linear ultrasonic motor utilizing the actuating approach of longitudinal-traveling-wave/bending-standing-wave hybrid excitation

Jiang Wu,Lipeng Wang,Fuxin Du,Guoteng Zhang,Jianye Niu,Xuewen Rong,Rui Song,Huijuan Dong,Jie Zhao,Yibin Li

DOI: https://doi.org/10.1016/j.ijmecsci.2023.108223

IF: 7.3

2023-02-16

International Journal of Mechanical Sciences

Abstract:Ultrasonic motors (USMs) have been extensively investigated for a few decades, but it is still required to improve their thrust force (or torque) density and/or power density for practical usage. According to conventional actuating methods, the dimensions of the transducers are difficult to greatly change after modal degeneration; this restricts the possibility of weight reduction. To tackle this problem, an actuating approach via longitudinal-traveling-wave (LTW) and bending-standing-wave (BSW) hybrid excitation is proposed and applied to a two-DOF linear ultrasonic motor in cross shape. Here, the driving force is generated with the LTW excited by modulating the phases according to the lengths of the transducers, while the elliptical motion shape is adjusted by tuning the BSW for optimal actuation. To assess the validity, a pair of Mason-circuit-based dynamic models were initially constructed to discuss three-dimensional vibration properties of the LTW and BSW on the cross-shaped transducer. Subsequently, a prototype with the size of 68 × 68 × 28 mm 3 was designed and fabricated to form a motor capable of horizontally moving in the x and y axes. Finally, the movement and load characteristics were evaluated experimentally. At 250 V voltage and 27.4 kHz frequency, the motor yielded the maximal thrust force, no-load sliding speed, and maximal output power of 42.1 N, 833 mm/s, and 7.7 W, respectively, along the x axis; and 40.2 N, 877 mm/s, 8.1 W, respectively, along the y axis. Moreover, the thrust force density and power density reach respectively 188.3 N/kg and 36 W/kg, exceeding the values of most conventional two-DOF linear USMs. These results demonstrate high actuating capability induced by the LTW/BSW hybrid excitation and provide a new method to design powerful two-DOF linear motors.

engineering, mechanical,mechanics
A dual-stator threaded linear ultrasonic motor with preload mechanism.

Lei You,Gaoren Zhang,Zhengxiang Yu,Yuhan Yang,Hongfei Qin,Menghui Liu,Zhongying Wang

DOI: https://doi.org/10.1063/5.0217944

IF: 1.6

2024-10-01

Review of Scientific Instruments

Abstract:The cylindrical ultrasonic motor, noted for its straightforward design, ease of miniaturization, and high precision, has significant potential in fields such as optics, healthcare, and precision engineering. However, miniaturization presents challenges, including diminished output force and complications in applying preloading stress. To address the reduced output force, this study presents a dual-stator, high-thrust cylindrical linear ultrasonic motor. This innovative motor features two stators, a mover, and a mechanism for applying preloading stress. A key design element is the parallel arrangement of the two stators along a threaded output shaft, separated by elastic components. This setup enables axial preloading via the threads' engagement. Simulations were conducted to refine the stators' parameters, assess their operational modes, and evaluate their in-plane paths. A prototype was subsequently built to test its impedance characteristics and mechanical performance. Test results showed that under a 200 Vpp drive, the single-stator motor generated a maximum force of 4.3 N, while the dual-stator configuration produced 6.8 N. After applying preloading stress, the output force of the dual-stator motor increased to 9.4 N.

Engineering,Medicine
A Novel Two-Degree-of-freedom Spherical Ultrasonic Motor Using Three Travelling-Wave Type Annular Stators

Jian Wang,Xi-xing Hu,Ban Wang,Ji-feng Guo

DOI: https://doi.org/10.1007/s11771-015-2646-z

2015-01-01

Journal of Central South University

Abstract:In order to promote the tolerance and controllability of the multi-degree-of-freedom (M-DOF) ultrasonic motor, a novel two-degree-of-freedom (2-DOF) spherical ultrasonic motor using three traveling-wave type annular stators was put forward. Firstly, the structure and working principle of this motor were introduced, especially a spiral spring as the preload applied component was designed for adaptive adjustment. Then, the friction drive model of 2-DOF spherical motor was built up from spatial geometric relation between three annular stators and the spherical rotor which was used to analyze the mechanical characteristics of the motor. The optimal control strategy for minimum norm solution of three stators’ angular velocity was proposed, using Moore-Penrose generalized inverse matrix. Finally, a 2-DOF prototype was fabricated and tested, which ran stably and controllably. The maximum no-load velocity and stall torque are 92 r/min and 90 mN·m, respectively. The 2-DOF spherical ultrasonic motor has compact structure, easy assembly, good performance and stable operation.
Study of a New Type Linear Ultrasonic Motor with Double-Driving Feet

Cunyue Lu,Tian Xie,Tieying Zhou,Yu Chen

DOI: https://doi.org/10.1016/j.ultras.2006.05.191

IF: 4.2

2006-01-01

Ultrasonics

Abstract:A new type linear USM with double-driving feet has been developed. The stator consists of eight piezoelectric ceramic plates and one brass plate. Piezoelectric ceramics plates are polarized along the thickness and are symmetrically bonded to the two surfaces of one rectangle brass plate. Double-driving feet are assembled on the same side of the brass plate. The working vibration mode is a composite in-plane bimode, which consists of the first longitudinal in-plane vibration mode and the second bending one. The basic size of the linear USM is determined carefully by FEA. The characteristics of the prototype motor were measured experimentally.
Statics Analysis of 3 DOF Spherical Traveling Wave Ultrasonic Motor Based on a Spiral Form of Spring

FU Ping,HU Xi-xing,GUO Ji-feng

DOI: https://doi.org/10.7631/issn.1000-2243.2014.02.0250

2014-01-01

Abstract:Three degree- of- freedom spherical traveling wave ultrasonic motor is a kind of multi degree- of- freedom motor. A novel type of traveling wave three degree- of- freedom spherical ultrasonic motor based on a spiral form of the spring was developed in this paper. In order to get its motion rule, statics analysis of the motor was to be discussed. The key issue of the self- regulation between the stators and the spherical rotor are solved by making use of the special- made spring. The preload between the stators and the spherical rotor is more smooth. The driving principle and basic structure of this kind of ultrasonic motor were introduced and the coordinate transformation model and position relation of rotor and stators of spherical ultrasonic motor were also set up. Then stress of rotor and contact force of rotor and stators on the contact circle were also analyzed. Through the force balance equation of its stator and rotor,relation of micro displacement of the center of rotor and axial compaction and preload force of stators were presented in this paper. Also the basic relation of this kind of spherical motor were given out. Through simulation,the mechanical characteristics of this type of motor is got. This article lays a theoretical foundation for control strategy of the motor. The diameter of prototype motor is 40 mm in rotor and 30 mm in stator and maximum holding torque is 0. 09 N·m,maximum speed is 90 r·min- 1. From the above discussion and practical experiments availability of devices is to be verified.
Kinetic Model of Three Degree-of-Freedom Traveling Wave Type Ultrasonic Motor

Ping Fu,Jifeng Guo

2008-01-01

Abstract:Three Degree-of-Freedom (3DOF) traveling wave type ultrasonic motor (USM) can move at three degrees. The principle and basic structure of 3DOF traveling-wave type USM are presented in this paper firstly. Then through coordinate conversion the distribution of the force on the contact area of rotor and stators can be obtained when the rotor rotates. Thus the motorpsilas driving and friction force can be calculated on the contact area. Also the driving and friction torque can be derived. By solving the equations of torque balance and force balance of stator the motorpsilas kinetic model can be deduced. By simulation structure parameters and stator velocity are analyzed and the model can be verified preliminarily.
A New Standing-Wave-type Linear Ultrasonic Motor Based on In-Plane Modes.

Yunlai Shi,Chunsheng Zhao

DOI: https://doi.org/10.1016/j.ultras.2010.11.006

IF: 4.2

2011-01-01

Ultrasonics

Abstract:This paper presents a new standing-wave-type linear ultrasonic motor using combination of the first longitudinal and the second bending modes. Two piezoelectric plates in combination with a metal thin plate are used to construct the stator. The superior point of the stator is its isosceles triangular structure part of the stator, which can amplify the displacement in horizontal direction of the stator in perpendicular direction when the stator is operated in the first longitudinal mode. The influence of the base angle θ of the triangular structure part on the amplitude of the driving foot has been analyzed by numerical analysis. Four prototype stators with different angles θ have been fabricated and the experimental investigation of these stators has validated the numerical simulation. The overall dimensions of the prototype stators are no more than 40 mm (length) × 20 mm (width) × 5 mm (thickness). Driven by an AC signal with the driving frequency of 53.3 kHz, the no-load speed and the maximal thrust of the prototype motor using the stator with base angle 20° were 98 mm/s and 3.2N, respectively. The effective elliptical motion trajectory of the contact point of the stator can be achieved by the isosceles triangular structure part using only two PZTs, and thus it makes the motor low cost in fabrication, simple in structure and easy to realize miniaturization.
Two Degree of Freedom Spherical Ultrasonic Motor With Three Traveling-wave Stators

HU Xi-xing,GUO Ji-feng

DOI: https://doi.org/10.13334/j.0258-8013.pcsee.2010.09.011

2010-01-01

Abstract:A novel type of 2DOF (two degree of freedom) spherical ultrasonic motor with three traveling-wave type stators was developed.Its structure and driving principle are introduced,especially a spiral form of the spring was presented.The key issue of the self-regulation between the stators and the spherical rotor was solved,and the errors caused by processing and installation were overcomed by making use of the special-made spring.Ensured that the preload between the stators and the spherical rotor was more uniform and smooth.The mathematics model of the motor was established based on the Friction Drive Model,and the analytical expression of mechanical characteristics calculation was deduced.The features of the mechanical characteristics were acquired by make the minimum Euclidean norm as a target.The developed motor has φ40 mm rotor,the maximum output torque reaches 0.12N·m,the maximun speed is 90r/min,and the performance is consistent in all directions.This type spherical motor has many advantages of compact structure,convenient installation,prominent performance.It has significant application in many field,such as robotics manipulator's joint,CCD working stage.
Optimization research of stator with two degree-of-freedom traveling-wave spherical ultrasonic motor

Ping FU,Xi-xing HU,Ji-feng GUO

DOI: https://doi.org/10.3969/j.issn.1003-3076.2015.05.006

2015-01-01

Abstract:The driving principle and basic structure of this kind of spherical ultrasonic motor are firstly introduced.Then optimal structure of stator is analyzed. By the established finite element model the stator vibration modal analysis is carried out and the resonance frequency can be calculated. And then according to the optimization conditions for dip angle of stator,the structure of the stator is optimized. Through ANSYS software the modal analysis and the harmonious response analysis in different dip angles of stator can be completed. So relation between resonance frequency of stator and dip angle can be deduced. Finally test of designed stator is carried out by laser vibration test system. The best angle of the stator can be determined and the significant experimental data can also be obtained.The test results show that the optimized stator is more in line with the actual operation characteristics,which is a more accurate guide for the motor design.
Modeling and Performance Evaluation of 2dof Spherical Traveling-Wave Type Ultrasonic Motor

Xixing Hu,Jifeng Guo,Runjie Shen

2008-01-01

Abstract:The objective of our research is to investigate the performance evaluation of traveling-wave ultrasonic motor with two-degree of freedom (2DOF-USM). The space structure of 2DOF-USM is introduced briefly. The mathematic model of the motor is established based on friction drive mechanism. Through relation of space location, calculating the driving force and friction force at arbitrary point of contact area, the analytical expressions of the mechanical characteristics are deduced. The influence of model parameter on motor characteristics is presented through simulation. The validity of the model is verified by means of comparing the simulation results and the experimental ones. This article lays a theoretical foundation for spherical traveling-wave type ultrasonic motorpsilas well performance and trajectory control next step. The maximum output torque of developed motor reaches 0.10 Nmiddotm, the maximum speed is 90 rpm.
Single stator 3-DOF ultrasonic motor and its control

Weiqing Huang,Zhirong Li,Chunsheng Zhao

DOI: https://doi.org/10.1109/ULTSYM.2004.1418194

2004-01-01

Abstract:A three degree-of-freedom (DOF) ultrasonic motor (USM) with single cylinder-shaped stator and a spherical rotor was developed using one first order longitudinal and two second order bending nature vibration modes of the cylinder. Control strategies for two DOF trajectory following are studied and applied to the prototype USM. Vibration amplitude control is employed for speed regulation. Our first trajectory following strategy is the step-by-step interpolation. The second strategy is vector decomposition control. Three pulse width modulation (PWM) methods were investigated for the exciting source voltage regulation. These methods were compared and experimentally verified by several experiments. The vector control method takes several advantages, such as small trajectory following error, smooth moving and hence low noise.
Contact Mode and Force Transferring Model of Cylindrical Ultrasonic Motors with Bending Vibration Modes

WANG Jian,GUO Jifeng,LU Cunyue,WANG Wenhao,TIAN Jianchuang

DOI: https://doi.org/10.3321/j.issn:0371-0025.2007.06.005

2007-01-01

Acta Acustica

Abstract:Cylindrical ultrasonic motors can be widely used in many fields such as zoom and focus system of cameras, electric curtain and micro-driver of MEMS.This work concentrates on single-point and double-point contact modes between the stator and the rotor,which are proved by the theory and the experiment,then put forward a conception of the critical pre-pressure and the force transferring relation in two different contact modes mentioned above,moreover analyze the mechanical characteristics and the efficiency of the motors.Simulated results are confirmed by experimental ones.The proposed model is useful to analyze the relation between the motor characteristics and the pre-pressure. Finally theφ14 mm prototype was fabricated.Its maximum torque is 0.11 Nm,the no-load speed is about 300 r/min.

Re-evaluating lipotoxic triggers in skeletal muscle: relating intramyocellular lipid metabolism to insulin sensitivity.

Self-driving linear ultrasonic motor with double vibrators

Standing Wave-Type Bi-Directional Linear Moving Ultrasonic Motor Using Plates and Weak Links

A linear ultrasonic motor with a hollowed and symmetrical stator

Development of a Radial-Torsional Vibration Hybrid Type Ultrasonic Motor with a Hollow and Short Cylindrical Structure

Design and Dynamic Simulation of a Novel Traveling Wave Linear Ultrasonic Motor

A Hollow Cylindrical Linear Nut-Type Ultrasonic Motor

Localization effects of acetylcholine release from a synaptic vesicle at the neuromuscular junction.

Modeling and tests for a stator of a traveling-wave type spherical ultrasonic motor with 2-DOF

A two-DOF linear ultrasonic motor utilizing the actuating approach of longitudinal-traveling-wave/bending-standing-wave hybrid excitation

A dual-stator threaded linear ultrasonic motor with preload mechanism.

A Novel Two-Degree-of-freedom Spherical Ultrasonic Motor Using Three Travelling-Wave Type Annular Stators

Study of a New Type Linear Ultrasonic Motor with Double-Driving Feet

Statics Analysis of 3 DOF Spherical Traveling Wave Ultrasonic Motor Based on a Spiral Form of Spring

Kinetic Model of Three Degree-of-Freedom Traveling Wave Type Ultrasonic Motor

A New Standing-Wave-type Linear Ultrasonic Motor Based on In-Plane Modes.

Two Degree of Freedom Spherical Ultrasonic Motor With Three Traveling-wave Stators

Optimization research of stator with two degree-of-freedom traveling-wave spherical ultrasonic motor

Modeling and Performance Evaluation of 2dof Spherical Traveling-Wave Type Ultrasonic Motor

Single stator 3-DOF ultrasonic motor and its control

Contact Mode and Force Transferring Model of Cylindrical Ultrasonic Motors with Bending Vibration Modes