[Postmortem slitlamp study of the vitreous body. 3. Relation to histology, biomicroscopy and clinical applications].

G. Eisner

DOI: https://doi.org/10.1007/BF00406515

Abstract:

What problem does this paper attempt to address?

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

ZH Huang,HB Lu,DM Jiang,K Zeng,B Liu,JQ Zhang,XB Wang

DOI: https://doi.org/10.1243/095440704773599944

2004-01-01

Abstract:A stabilized diesel-methanol blend was realized and a study on the performance and emissions of the diesel-methanol blend was carried out in a compression ignition engine. The study showed that the engine thermal efficiency increases and the diesel equivalent b.s.f.c. decreases with increase in the oxygen mass fraction (or methanol mass fraction) of the diesel-methanol blends due to an increased fraction of premixed combustion phase, oxygen enrichment and improvement in the diffusive combustion phase. Further increase in the fuel delivery advance angle will achieve a better engine thermal efficiency when the diesel engine is operated using the diesel-methanol fuel blends. A marked reduction in the exhaust CO and smoke can be achieved when operating with the diesel-methanol blend. There is not a large variation in the exhaust hydrocarbon with the addition of methanol in diesel fuel. NOx increases with increase in the mass of methanol added; methanol addition to diesel fuel was found to have a strong influence on the NOx concentration at high engine loads rather than at low engine loads, and a flat NOx-smoke trade-off curve exists when operating with the diesel-methanol fuel blends.
Combustion and Emission Characteristics of a DI Diesel Engine Fueled by Diesel-Methanol Blends

张俊强,卢红兵,王锡斌,蒋德明

DOI: https://doi.org/10.3321/j.issn:1006-8740.2004.02.016

2004-01-01

Abstract:The economy and power performances, combustion and emission characteristics of diesel-methanol blended fuels with different blend proportions (0, 15%, 20%) in a DI diesel engine have been studied. The various characteristics of blended fuels are recorded and compared with neat diesel fuel in order to study the influence of different quantities of methanol. The tests were carried out using the method of equal excess air coefficient. The results show that under the conditions of same engine speed and equal excess air coefficient,the brake thermal efficiency of diesel-methanol blended fuels is higher than that of neat diesel fuel due to the improvement of combustion caused by the properties of diesel-methanol blended fuels . Smoke emissions decrease dramatically and CO emissions reduce too with the increase of methanol content. NOx emissions, however, increase and reach the maximum value at a 10%～15% content of methanol.
Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

黄佐华,卢红兵,蒋德明,曾科,刘兵,张俊强,王锡斌

DOI: https://doi.org/10.3321/j.issn:1000-0909.2003.06.004

2003-01-01

Abstract:A stabilized diesel/methanol blend was realized and the combustion characteristics and heat release analysis of the diesel/methanol blend was carried out in a DI diesel engine. The study showed that the increase of methanol mass fraction of diesel/methanol blends will result in the increase of heat release rate in premixed burning phase and shorten the combustion duration of diffusive burning phase. Ignition delay increases with the increase of methanol mass fraction and the behavior is more obviously at low engine load and high engine speed. Rapid burn duration varies less with methanol mass fraction and the total combustion duration decreases with the increase of methanol mass fraction. At a low engine speed, the centre of heat release curve tends to be close to the top-dead-centre with the increase of methanol mass fraction at all engine loads and fuel delivery advance angles, and the maximum rate of pressure rise and the maximum rate of heat release increase with the increase of methanol mass fraction. At a high engine speed, the centre of heat release curve closes to the top-dead-centre with the increase of methanol mass fraction at high engine load and will depart from the top-dead-centre at low engine load, and the maximum rate of pressure rise and the maximum rate of heat release gives an increasing trend with the increase of the methanol mass fraction and a slight decreasing trend with further increasing of methanol mass fraction. Maximum cylinder gas pressure increases with the increase of methanol mass fraction when oxygen mass fraction is less than 6%, and then it remains a constant value or drops slightly with a further increase of oxygen mass fraction. Maximum mean gas temperature remains almost unchangeable versus methanol mass fraction.
Experimental Study of Cetane Number on Methanol/Biodiesel Combustion Characteristics

Ruina Li,Zhong Wang,Mingdi Li,Yang Zhao,Peiyong Ni,Shuai Liu

DOI: https://doi.org/10.11715/rskxjs.R201403058

2014-01-01

Abstract:Cetane number improver was added into methanol/biodiesel cetane number blends of 45.5,49.5,and 54.5 were obtained respectively. Utilizing 186,F diesel engine,the indicator diagram of diesel,methanol/biodiesel was measured at speed of the maximum torque and rated speed. The combustion process was studied. Results show that when cetane number of methanol/biodiesel increased from 45.5 to 54.5 at rated condition,the ignition delay period decreased from 12°,CA to 10°,CA,the combustion duration increased from 33°,CA to 36°,CA,the maximum cylin-der pressure increased from 7.75,MPa to 8.39,MPa,and the maximum rate of instantaneous heat release increased from 39.97,kJ/(°,CA) to 42.68,kJ/(°,CA). At maximum torque condition,the ignition delay period decreasedfrom 12°,CA to 9°,CA,the combustion duration increased from 31°,CA to 35°,CA,the maximum cylinder pressure in-creased from 8.08,MPa to 8.48,MPa,and the maximum rate of instantaneous heat release increased from 36.13,kJ/(°,CA) to 41. 37,kJ/(°,CA).
Experimental investigation of emissions from a single-cylinder diesel engine using methanol–diesel blends

Mohammed Qays Kadhim,Petr Platonovich Oshchepkov

DOI: https://doi.org/10.3389/fenrg.2024.1449652

IF: 3.4

2024-09-23

Frontiers in Energy Research

Abstract:This study examines the effects of methanol–diesel blends on the emissions of a diesel engine, concentrating on carbon monoxide (CO), carbon dioxide (CO 2 ), nitrogen oxides (NOx), hydrocarbons (HCs), and particulate matter (PM). Using a single-cylinder four-stroke diesel engine at varying torque settings (2 N m–6 N m), significant reductions in CO, CO 2 , HC, and PM emissions were observed with increasing methanol content. CO emissions reduced by up to 81.8%, CO 2 by up to 64.2%, HC by up to 80.4%, and PM by up to 23.5% with the MD11 blend. NOx emissions initially increased but decreased by up to 20% at higher torques with the same blend. These results highlight the environmental benefits of methanol–diesel blends and the need for effective NOx reduction strategies.

energy & fuels
Study on Particulate Structure Characteristics of Diesel Engines Fueled with a Methanol/Biodiesel Blend

Ruina Li,Zhong Wang,Chunyi Tang,Xin Meng

DOI: https://doi.org/10.1021/acsomega.0c04371

IF: 4.1

2021-02-23

ACS Omega

Abstract:Methanol and biodiesel are both alternative fuels of diesel engines. In order to study the effects of methanol on the microstructure of particulates produced from the diesel engine fueled with a methanol/biodiesel blend, the methanol/biodiesel blend fuels with 0, 10, and 20% methanol were prepared (named B100, BM10, and BM20, respectively). SEM and TG experiments have been carried out, and the structural and oxidative characteristics of particulates for the methanol/biodiesel blend were investigated. The results showed that the average diameters of B100, BM10, and BM20 particulates were 35, 32.6, and 31.2 nm, respectively. With the increase of methanol blending ratio, the H<sub>2</sub>O and SOF (soluble organic fraction) contents were increased and the soot content in particulates was reduced slightly. In addition, the activation energy of the particulate pyrolysis reaction was reduced with the increase of methanol mixing ratio, and the oxidative reaction of particulates was easier to carry out.This article has not yet been cited by other publications.

chemistry, multidisciplinary
Experimental investigation of Performance, Emission, and Combustion characteristics of a diesel engine using blends of Waste Cooking Oil-Ethanol biodiesel with MWCNT nanoparticles

M. Sonachalam,V. Manieniyan,Senthilkumar R,Ramis M. K,Mahammadsalman Warimani,Raman Kumar,Ankit Kedia,T.M.Yunus Khan,Naif Almakayeel

DOI: https://doi.org/10.1016/j.csite.2024.105094

IF: 6.268

2024-09-10

Case Studies in Thermal Engineering

Abstract:In this study, blends of 5% and 10% ethanol with waste cooking oil biodiesel are mixed with Multi-Walled Carbon Nanotubes (MWCNT) at a concentration of 30 ppm. MWCNTs, known for their high surface area and unique properties, are added to potentially enhance combustion efficiency and reduce emissions. These blends are then tested in a diesel engine to evaluate their performance, emission and combustion characteristics using Design of experiment technique. After conducting various experiments and analyses, the blend of 20% biodiesel, 10% ethanol, and 30 ppm MWCNT was identified as the most optimal due to its favorable engine characteristics. Brake Thermal Efficiency (BTE) was increased from 3.1% to 3.4% with the addition of MWCNTs, indicating enhanced fuel efficiency. Moreover, average Fuel Consumption is decreased from 2.2% to 2.5%, suggesting improved fuel utilization. Using MWCNT 30 ppm in B20 ethanol blends (MWCNT 30 ppm B20+E10) resulted in 35% reduction in nitrogen oxide (NOx) emissions, 37% reduction in CO emissions and 39% reduction in HC emissions. Hence MWCNTs demonstrated effectiveness in mitigating harmful exhaust emissions The optimized values for all parameters fall within acceptable ranges, indicated successful optimization using Response surface methodology. Additionally, statistical analysis reveals that the machine learning- XGBoost model outperformed all other advanced machine learning models across all tested metrics, including MSE, MAE, and R-square.

thermodynamics
Study on Combustion and Emission Characteristics of a Diesel Engine Fuelled with Ethanol/Diesel/Methyl Ester Blends

Bang-quan HE,Jian-xin WANG

DOI: https://doi.org/10.3321/j.issn:1000-0909.2005.04.008

2005-01-01

Abstract:The feasibility of methyl ester as an additive for the ethanol-diesel blends was investigated, and the comparisons in combustion and emission characteristics of a diesel engine fuelled with diesel, ethanol/diesel/methyl ester, ethanol/methyl ester and pure methyl ester were made respectively. The results showed that methyl ester could be used as an additive for ethanol/diesel blends, and oxygenated fuels could significantly reduce the exhaust smoke at the medium and high loads compared to that of diesel operation. Blend containing 30% volume of ethanol and 70% volume of methyl ester gave the lowest smoke emission. However, ignition delay and total hydrocarbon (THC) emissions would be increased along with high value of pressure rise rate and NO_x at medium and high loads with the use of ethanol/diesel blends.
Preparation and Emission Characteristics of Ethanol-Diesel Fuel Blends

RD Zhang,H He,XY Shi,CB Zhang,BQ He,JX Wang

2004-01-01

Abstract:The preparation of ethanol-diesel fuel blends and their emission characteristics were investigated. Results showed the absolute ethanol can dissolve in diesel fuel at an arbitrary ratio and a small quantity of water (0.2%) addition can lead to the phase separation of blends. An organic additive was synthesized and it can develop the ability of resistance to water and maintain the stability of ethanol-diesel-trace amounts of water system. The emission characteristics of 10%, 20%, and 30% ethanol-diesel fuel blends, with or without additives, were compared with those of diesel fuel in a direct injection(DI) diesel engine. The experimental results indicated that the blend of ethanol with diesel fuel significantly reduced the concentrations of smoke, hydrocarbon(HC), and carbon monoxide (CO) in exhaust gas. Using 20% ethanol-diesel fuel blend with the additive of 2% of the total volume, the optimum mixing ratio was achieved, at which the bench diesel engine testing showed a significant decrease in exhaust gas. Bosch smoke number was reduced by 55%, HC emission by 70%, and CO emission by 45%, at 13 kW/1540 r/min. However, ethanol-diesel fuel blends produced a few ppm acetaldehydes and more ethanol in exhaust gas.
Emission analysis of diesel and butanol blends in research diesel engine

Nivin Joy,K. N. Balan,Beemkumar Nagappan,Sajin Justin Abraham baby

DOI: https://doi.org/10.1080/10916466.2019.1702680

IF: 1.695

2019-12-28

Petroleum Science and Technology

Abstract:This study is aimed at reducing NOx, Smoke, HC, CO emissions from single-cylinder, four-stroke, and water cooled diesel engine. The research engine is fueled with diesel and two blends of butanol and diesel at atmospheric conditions. Neat diesel is termed as D100, 10%, and 20% Volume of butanol dispersed in D100 is termed as D90B10 and D80B20 respectively. The chemical and physical properties of D100, D90B10 and D80B20 fall within the limits of ASTM standards. Results revealed that enhanced chemical properties and higher latent heat of vaporization of butanol lowered the CO, HC, smoke, and NOX emissions of diesel fueled research diesel engine.

energy & fuels,engineering, chemical, petroleum
Effects of Methanol Addition on the Combustion Process of the Methanol/Diesel Dual-Fuel Based on an Optical Engine

Jinping Liu,Guangzhao Guo,Mingrui Wei

DOI: https://doi.org/10.3390/en16247946

IF: 3.2

2023-12-08

Energies

Abstract:The combustion process of traditional diesel engines is mainly determined by the injection timing of diesel. There is a trade-off relationship between the soot and NOx (nitrogen oxides) during this combustion process, making it difficult to reduce these two emissions simultaneously. The use of methanol can not only solve the above problem, but also replace some fossil fuels. However, the effects of methanol injection into the intake duct on the flame propagation in diesel/methanol dual-fuel engines is not yet clear, and there is relatively little research on it. The effects of methanol addition on the combustion process of diesel/methanol dual fuel (DMDF) were achieved based on a modified optical engine in this paper. One injector is installed on the intake inlet to inject methanol, and the other injector is installed in the cylinder to inject diesel in two stages before the top dead center of compression. There are three tests conducted separately in this paper. Firstly, the effects of the methanol ratio (40%, 50%, 60%, and 70%) on the combustion process are investigated, with the total heat remaining unchanged. Secondly, the effects of the pre-injection mass of diesel (20%, 30%, 40%, and 50%) on the combustion process are investigated, which keeps the total diesel mass unchanged. Finally, the effects of the total mass of diesel on the combustion process are investigated while maintaining the mass of methanol unchanged. The dual-fuel combustion process is recorded by a high-speed camera. A combustion analyzer and other equipment were used to analyze the combustion. The results showed that CA10 is delayed, the pressure and the heat release rate (HRR) are reduced, and the number of pixels of the KL factor (KL) decreases significantly with the increasing methanol ratio. CA10 and CA50 are advanced, the pressure and HRR decrease, and the KL increases when the mass of pre-injected diesel increases. CA10 and CA50 are advanced, respectively, and CA90 is postponed due to the increase in diesel mass. The pressure and HRR increase, and the KL increases when the total mass of diesel increases.

energy & fuels
Emission Characteristics Using Methyl Soyate-Ethanol-Diesel Fuel Blends on A Diesel Engine

X Shi,Y Yu,H He,S Shuai,J Wang,R Li

DOI: https://doi.org/10.1016/j.fuel.2005.03.001

IF: 7.4

2005-01-01

Fuel

Abstract:A blend of 20% (v/v) ethanol/methyl soyate was prepared and added to diesel fuel as an oxygenated additive at volume percent levels of 15 and 20% (denoted as BE15 and BE20). We also prepared a blend containing 20% methyl soyate in diesel fuel (denoted as B20). The fuel blends that did not have any other additive were stable for up to 3 months. Engine performance and emission characteristics of the three different fuels in a diesel engine were investigated and compared with the base diesel fuel. Observations showed that particulate matter (PM) emission decreased with increasing oxygenate content in the fuels but nitrogen oxides (NOx) emissions increased. The diesel engine fueled by BE20 emitted significantly less PM and a lower Bosch smoke number but the highest NOx among the fuel blends tested. All the oxygenate fuels produced moderately lower CO emissions relative to diesel fuel. The B20 blend emitted less total hydrocarbon (THC) emissions compared with base diesel fuel. This was opposite to the fuel blends containing ethanol (BE15, BE20), which produced much higher THC emission.
Diesel Emission Improvements by the Use of Oxygenated DME/diesel Blend Fuels

Y Wang,LB Zhou,HW Wang

DOI: https://doi.org/10.1016/j.atmosenv.2005.12.016

IF: 5

2006-01-01

Atmospheric Environment

Abstract:A kind of oxygenate fuel, DME, has been proposed and tested for use with diesel fuel as a means of reducing exhaust emissions. The addition of DME to diesel fuel results in the decrease of the lower calorific value, aromatics fraction and kinematic viscosity of blend fuels. Simultaneously, cetane number, C/H ratio and oxygen content of the blends are enhanced, which has some favorable effects on the combustion and emission of the blends with 10%, 20% and 30% DME by mass. The study on the performance and emissions of the diesel/DME blend is conducted in a DI engine. The emission characteristics of four fuels are determined in a diesel engine. At high loads, the blends reduce smoke significantly with a little penalty on CO and HC emissions compared to diesel fuel. NOx and CO2 emissions of the blends are decreased somewhat. At low loads, the blends have slight effects on smoke reduction due to overall leaner mixture. The results indicate the potential of diesel reformation for clean combustion in diesel engines.
A comparative study of combustion and emission characteristics of dual-fuel engine fueled with diesel/methanol and diesel–polyoxymethylene dimethyl ether blend/methanol

Hao Chen,Jingjing He,Zhanming Chen,Limin Geng

DOI: https://doi.org/10.1016/j.psep.2021.01.007

IF: 7.8

2021-03-01

Process Safety and Environmental Protection

Abstract:In this study, a comparative study of the combustion characteristics and performances of a dual-fuel engine fueled with diesel/methanol and diesel–polyoxymethylene dimethyl ether blend/methanol was conducted. All the experiments were conducted on a heavy-duty common rail diesel engine at an engine speed of 1800 r/min. The engine loads were fixed at low, medium, and heavy loads, with the brake mean effective pressure at 0.42 MPa, 0.7 MPa and 0.9 MPa, respectively. Methanol substitution ratio (MSR) was defined as the torque output contributed by methanol to the total torque output, and in this study, three MSRs (0 %, 20 %, and 40 %) were defined. Diesel–polyoxymethylene dimethyl ether (PODE) blend was defined as P50 (50 % diesel and 50 % PODE by volume) to clarify the effect of PODE addition on engine performance. The results showed that the dual-fuel engine fueled with P50/methanol had a higher peak cylinder pressure, lower first peak heat release rate (HRR), and higher second peak HRR than the dual-fuel engine fueled with diesel/methanol. Both the ignition delay and combustion duration of the dual-fuel engine decreased when the pilot fuel injection changed from diesel to P50. Moreover, both NOx emissions and particulate matter produced by the P50/methanol engine were lower than those produced by the diesel/methanol engine for the specific MSR and engine load.

engineering, environmental, chemical
Diesel/methanol dual-fuel combustion: An assessment of soot nanostructure and oxidation reactivity

Xiaochen Wang,Jianbing Gao,Hao Chen,Zhanming Chen,Peng Zhang,Zhenbin Chen,Xiaochen Wang,Jianbing Gao,Hao Chen,Zhanming Chen,Peng Zhang,Zhenbin Chen

DOI: https://doi.org/10.1016/j.fuproc.2022.107464

IF: 8.129

2022-12-01

Fuel Processing Technology

Abstract:The use of renewable methanol partly substituting diesel fuel can support the transition to low-carbon engines, in the form of diesel/methanol dual-fuel combustion. Particulate filters are still required for diesel/methanol dual-fuel combustion engines to meet the emission standard. Their periodical regeneration depends on the soot oxidation reactivity and nanostructure. We therefore assessed the influences of premixing methanol on soot oxidation reactivity and nanostructure at both engine loads. The results showed that increasing methanol substitution ratio shifted thermogravimetric profiles towards low temperature direction. The average activation energies of M20 and M40 samples (the methanol substitutions of 20% and 40%) dropped by 41.1–43.9 kJ/mol and 53.2–99.7 kJ/mol compared to diesel one at both engine loads, respectively. With an increase in methanol substitution ratio, a notable reduction in primary particle size was observed, with the shorter and more tortuous fringes as well as larger separation distance between the stacked fringes. The increasing trend in soot oxidation reactivity with methanol addition correlated well with the changes in primary particle size and fringe parameters, which means that soot oxidation reactivity highly depends on its morphology and nanostructure. It can be expected from the results that diesel/methanol dual-fuel operation has the advantages in engine fuel economy improvement regarding the regeneration of particulate filters.

energy & fuels,engineering, chemical,chemistry, applied
Mitochondrial multiorgan disorder syndrome (MIMODS) due to a compound heterozygous mutation in the ACAD9 gene☆

J. Finsterer,S. Zarrouk-Mahjoub

DOI: https://doi.org/10.1016/j.ymgmr.2017.07.009

IF: 2.082

2017-07-28

Molecular Genetics and Metabolism Reports

Abstract:
Experimental study on macro spray, combustion and emission characteristics of biodiesel and diethyl carbonate blends

L. Zhao,X. Zhu,R. Zhao,J. Tian,D. Qian,Q. Lin

DOI: https://doi.org/10.1007/s13762-024-05935-8

2024-08-20

International Journal of Environmental Science and Technology

Abstract:Biodiesel has a higher viscosity and poorer atomization effect compared to traditional diesel fuel, resulting in lower combustion efficiency. This study investigated the effects of exhaust gas recirculation and a diethyl carbonate additive on the combustion and emission of biodiesel blends. Biodiesel was blended with DEC (90% volume biodiesel + 10% volume DEC: B90DEC10). Experiments were conducted at various brake mean effective pressures (BMEP: 0.2, 0.6, 1.0, 1.6, and 2.0 MPa) and EGR rates (0, 5, and 15%) on a direct injection and high pressure common rail diesel engine that met Euro VI emission standards. The results revealed that the viscosity and atomization effects of B90DEC10 were improved, and the premixed combustion period was longer and the heat release rate (HRR) was higher compared to traditional diesel. The maximum HRR of B90DEC10 was 20% higher than that of diesel at 0.6 MPa. Compared to diesel, the particulate matter emissions of B90DEC10 were reduced by 92%, and total hydrocarbons and carbon monoxide emissions were significantly reduced. However, there was an increase of 8–20% in nitrogen oxide emissions. At an EGR rate of 15%, the NO x emissions of B90DEC10 were reduced by 45%, while having minimal impact on PM emissions and brake thermal efficiency. Therefore, it was concluded that B90DEC10 is a potential alternative to diesel, and the combustion performance and emissions control were optimized when using a higher EGR rate (15%).

environmental sciences
Potential improvement in conventional diesel combustion mode on a common rail direct injection diesel engine with PODE/WCO blend as a high reactive fuel to achieve effective Soot-NOx trade-off

Inbanaathan Papla Venugopal,Dhinesh Balasubramanian,Amudhan Rajarajan

DOI: https://doi.org/10.1016/j.jclepro.2021.129495

IF: 11.1

2021-12-01

Journal of Cleaner Production

Abstract:Many countries in and around the world have conducted various studies on biodiesel usage over common rail direct injection (CRDI) diesel engines, among which waste cooking oil (WCO) biodiesel has made a major impact on diesel engine research because of its cost-efficient nature and elimination of waste disposal. The deposits of carbon and very high viscosity are some of the key factors which deteriorate the usage of raw WCO biodiesel. Lower volume proportionate blends of WCO biodiesel produce excellent combustion characteristics reducing hydrocarbon (HC), carbon mono oxide (CO), and soot emissions, but they seem to promote the formation of nitrous oxides (NOx). As a solution to overcome this problem, polyoxymethylene dimethyl ether (PODE) with lower viscosity, higher oxygen content, high cetane number, showing better combustion characteristics with a good soot-NOx trade-off is selected for the present research work. The novelty of the current research work shows the reduction of soot and NOx emissions using PODE/WCO/Diesel blends by varying the proportions in a conventional combustion mode of a CRDI diesel engine without any modifications which was lagging by the previous researches. A trans-esterified WCO biodiesel is blended with diesel in varying volumes as 10, 20, and 30%. The chemical properties of the blend fuels were determined using ASTM standards. The investigation was carried out and it was found that W20 blend fuel showed a highest reduction of 21.11%, 23.51%, and 22.45% of CO, HC, and soot emissions respectively with a rise of 6.39% of NOx emissions. W20 blend with a good soot-NOx trade-off was selected in which PODE was blended in varying proportions such as 10, 20, and 30% respectively. The properties of the test fuels were determined and the further investigation was carried out. This second stage of reduction was done in determining the fuel with excellent soot-NOx trade-off without compromising the performance of the engine. It was found that W20P20 blend fuel showed the highest reduction of 33.86%, 50.78%, and 80.86% of HC, CO, and Soot emissions with a slight increase of 0.78% of NOx emissions. Brake Thermal Efficiency was found better for W20P20 fuel in comparison with W20 fuel. Thus, two stages of reduction in emissions were carried out with the aim of meeting the stringent emissions norms in the conventional diesel combustion technique.

environmental sciences,green & sustainable science & technology,engineering, environmental
Environmental and performance impacts of 2-ethylhexyl nitrate and ethanol in diesel blends: A comprehensive study

Mahir Husain Salmani,Inayat Hussain,Sanaur Rehman,Himansh Kumar

DOI: https://doi.org/10.1063/5.0199235

IF: 2.847

2024-07-01

Journal of Renewable and Sustainable Energy

Abstract:This study investigates the performance and emissions of a compression ignition engine fueled with blends of ethanol and petroleum diesel with 2-EHN (2 ethylhexyl nitrate) as a cetane improver. Three blends, named E20 (20% ethanol with 80% diesel), E20A (20% ethanol, 0.1% 2-EHN, and 79.9% petroleum diesel), E20B (20% ethanol, 0.2% 2-EHN, and 79.8% petroleum diesel), and petroleum diesel were analyzed for their brake thermal efficiency (BTHE), specific fuel consumption, net heat release rate, indicated thermal efficiency, and emissions of carbon monoxide (CO), CO2, hydrocarbon (HC), and NOx. The experiments were conducted at variable loading conditions and at compression ratio of 16.5. Results showed that at no load conditions, petroleum diesel exhibited higher indicated power (IP) compared to E20, E20A, and E20B. However, at full load conditions, blend E20B showed higher IP compared to petroleum diesel, E20, and E20A. The blend E20B at a compression ratio of 16.5 showed the highest BTHE of 27%, compared to petroleum diesel (25%) under full load conditions, making it a better performing fuel. However, at higher loads and compression ratio of 16.5, the blends E20A and E20B exhibited emissions of CO, HC, CO2, and NOx that were significantly higher than diesel and E20 at all load conditions. Specifically, at full load conditions and compression ratio of 16.5, the emissions for each fuel were as follows: CO emission for E20, E20A, and E20B was around 0.01%, much less than petroleum diesel (0.1%); HC emission for E20 (15 ppm), E20A (17 ppm), E20B (10 ppm) was much higher than petroleum diesel (2.5 ppm); CO2 emission for E20, E20A, and E20B was about 13% less than petroleum diesel (15%); and NOx emission for E20, E20A, and E20B was around 150 ppm, comparable with petroleum diesel (140 ppm). These results imply that further improvements are required in using ethanol blended alternate fuel in diesel engines with 2-EHN (cetane improver) to reduce emissions with improved performance.

energy & fuels,green & sustainable science & technology
Effect of various ethanol/diesel cosolvents addition on combustion and emission characteristics of a CRDI heavy diesel engine

Jichao Liang,Quanchang Zhang,Qixin Ma,Zheng Chen,Zunqing Zheng

DOI: https://doi.org/10.1016/j.egyr.2021.12.011

IF: 5.2

2022-01-01

Energy Reports

Abstract:Solubility between ethanol and diesel impedes the application of ethanol in diesel engines. The objective of the experiment is to compare combustion and emission characteristics of ethanol/diesel fuels using biodiesel, n-pentanol, tetrahydrofuran (THF) as cosolvents respectively on a diesel engine under variable engine loads, exhaust gas recirculation (EGR) rates, and injection timings. The results show: All tested blends increase the indicated thermal efficiency (ITE) except at low load, and THF/ethanol/diesel fuel exhibits a higher ITE. The Coefficient of Variations of Indicated Mean Effective Pressure (COVIMEP) of ethanol/diesel blends is higher than that of diesel at low load. Under EGR conditions, ethanol/diesel blends run at lower COVIMEP, especially for biodiesel/ethanol/diesel fuel. At higher loads, all ethanol/diesel blends can decrease carbon monoxide (CO) emissions, especially for THF/ethanol/diesel fuel. Excessive retard of injection timing will increase CO and total hydrocarbon (THC) emissions of ethanol/diesel fuels. The soot emissions of THF/ethanol/diesel fuel are lower than those of n-pentanol/ethanol/diesel fuel under higher EGR rates. The effect of injection timing on soot emissions becomes more pronounced at slightly higher EGR rates. Compared to diesel, biodiesel/ethanol/diesel fuel increases nitrogen oxide (NOx) emissions, especially at medium-low load, whereas n-pentanol/ethanol/diesel and THF/ethanol/diesel fuels reduce NOx at low and high loads, slightly increase NOx emissions at medium loads. In conclusion, THF may be a more promising ethanol/diesel cosolvent compared with high alcohols and biodiesel in terms of fuel economy and emissions, especially under EGR and heavy load conditions.

[Postmortem slitlamp study of the vitreous body. 3. Relation to histology, biomicroscopy and clinical applications].

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Combustion and Emission Characteristics of a DI Diesel Engine Fueled by Diesel-Methanol Blends

Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

Experimental Study of Cetane Number on Methanol/Biodiesel Combustion Characteristics

Experimental investigation of emissions from a single-cylinder diesel engine using methanol–diesel blends

Study on Particulate Structure Characteristics of Diesel Engines Fueled with a Methanol/Biodiesel Blend

Experimental investigation of Performance, Emission, and Combustion characteristics of a diesel engine using blends of Waste Cooking Oil-Ethanol biodiesel with MWCNT nanoparticles

Study on Combustion and Emission Characteristics of a Diesel Engine Fuelled with Ethanol/Diesel/Methyl Ester Blends

Preparation and Emission Characteristics of Ethanol-Diesel Fuel Blends

Emission analysis of diesel and butanol blends in research diesel engine

Effects of Methanol Addition on the Combustion Process of the Methanol/Diesel Dual-Fuel Based on an Optical Engine

Emission Characteristics Using Methyl Soyate-Ethanol-Diesel Fuel Blends on A Diesel Engine

Diesel Emission Improvements by the Use of Oxygenated DME/diesel Blend Fuels

A comparative study of combustion and emission characteristics of dual-fuel engine fueled with diesel/methanol and diesel–polyoxymethylene dimethyl ether blend/methanol

Diesel/methanol dual-fuel combustion: An assessment of soot nanostructure and oxidation reactivity

Mitochondrial multiorgan disorder syndrome (MIMODS) due to a compound heterozygous mutation in the ACAD9 gene☆

Experimental study on macro spray, combustion and emission characteristics of biodiesel and diethyl carbonate blends

Potential improvement in conventional diesel combustion mode on a common rail direct injection diesel engine with PODE/WCO blend as a high reactive fuel to achieve effective Soot-NOx trade-off

Environmental and performance impacts of 2-ethylhexyl nitrate and ethanol in diesel blends: A comprehensive study

Effect of various ethanol/diesel cosolvents addition on combustion and emission characteristics of a CRDI heavy diesel engine