Abstract:The increasing global demand has prompted the development of more innovative ways to enhance the drilling of oil wells at lower costs, and avoid operational problems that affect the speed of drilling oil wells. The numerical cuttings trajectories simulation has been done to include the effect of cuttings collisions using commercial ANSYS FLUENT 2019 R3 CFD software. The (Eulerian-Eulerian) model was used to verify the cuts transport behavior due to the existence of liquid and solid phases. In this simulation, the mind transport rate is checked by changing the operational parameters which including (drilling mud flow rate and temperature, cuttings size, inclination, drill pipe rotation and eccentricity). The results show that the high degree of agreement was observed between the numerical results with experimental studied by the researcher Yaacob, indicating the CFD analysis system's dependability and capacity to mimic the drilling operation. The use of (Eulerian-Eulerian) model is found reliable in interpreting the phenomena of multiphase flow for understanding the mechanism of influence of parameters associated with the process of drilling oil wells on the lifting capacity. Increasing the flow velocity of the drilling mud transforms the flow pattern from laminar to turbulent, and the latter is one of the desired flow patterns during the flow that enable to increase the lifting capacity of the cuttings. The effect of the rotation speed of the drill pipe on the concentration of cuttings decreases when the flow rate of drilling fluid increases. the cuttings concentration when the flow velocity is 0.6 m/s reaches 48 % when the cuttings size is (0.5-1) mm and it attained to (60,57.52) % when the cuttings size is ((3.5-4) ,(2.25-3),(1.5-2)) mm respectively for the same flow velocity. The increase in the temperature of the drilling fluid weakened the ability of the drilling fluid to move the cuttings. At the flow velocity is 1.2 m/s and the drilling angle is 0 ̊ (vertical well), the cuttings concentration attained to 30 % within the annular space, while the concentration becomes (41, 44, 54, 32) % at the drilling angle (30 ̊, 45 ̊, 60 ̊, 90 ̊) respectively at the same stated flow velocity.

Determining whether the swirling jet is applicable in bottom-hole cleaning: A CFD study

Numerical Simulation of Effective Hole Cleaning by Using an Innovative Elliptical Drillpipe in Horizontal Wellbore

Performance Analysis of the Vortex Cuttings Cleaner: Turbine Hydraulic Drive and Cuttings Transport in Wellbore Annulus

Application of Computational Fluid Dynamics for Investigation the Effect of the Hole Cleaning Parameters in Inclined and Horizontal Wells

Fluid simulation in a cyclone reverse circulation well washing device based on computational fluid dynamics

Numerical investigation of flow patterns in cuttings transport for extended-reach horizontal wells with rotation drillpipe

Numerical simulation and experimental study of hole cleaning

CFD investigation of flow hydrodynamics and optimization in an industrial‐scale annular lance with swirl flow

Numerical Analysis of Swirling-Abrasive Water Jet Flow in the Nozzle

Experimental investigation and CFD simulation of multiphase flow behavior in air reverse circulation drilling

Experimental and Numerical Study on Air Flow Behavior for a Novel Retractable Reverse Circulation Drill Bit of Casing-while-Drilling (CwD)

Analysis and application of cleaning tool structure in negative pressure reverse circulating wellbore

Flow Field Simulation of Swirling Abrasive Jet Nozzle for Hard Rock Breaking

Research on deposition particles carrying with washing tools during well cleaning

Numerical investigation into the abrasive particle movement characteristics inside the swirling impeller nozzle based on the coupled SPH-FEM method

Key Structural Parameters Analysis Of Effective Hydroclean Drill Pipe

Investigation of the Jet Characteristics and Pulse Mechanism of Self-Excited Oscillating Pulsed Jet Nozzle

Numerical investigation on horizontal wellbore hole cleaning with a four-lobed drill pipe using CFD-DEM method

Insight into dust control performance of a reverse circulation drill bit using multiphase flow simulation

Study on cuttings removal effect of Effective HydroClean Drill Pipe under different deviation conditions of drill pipe

Study on Cleaning Effect of Different Water Flows on the Pulsed Cavitating Jet Nozzle