TRPM7 is required for ovarian cancer cell growth, migration and invasion.

Jing Wang,Q. Liao,Yi Zhang,Hui Zhou,Chenhui Luo,Jie Tang,Ying Wang,Yan Tang,Mingxuan Zhao,Xueheng Zhao,Qiong-Yu Zhang,Ling Xiao

DOI: https://doi.org/10.1016/j.bbrc.2014.10.118

2014-11-28

Abstract:

What problem does this paper attempt to address?

Effect of Curing Conditions on Property of High Performance Concrete with Composite Mineral Admixture

Lingli Gong,Nanguo Jin,Xianglin Gu,Xianyu Jin

DOI: https://doi.org/10.4028/www.scientific.net/kem.400-402.409

2009-01-01

Abstract:In this paper, the development of cubic compressive strength of concrete with the age was studied first. Four kinds of concrete, which were made from the mixes by using 0%, 20%, 30% and 40% Composite Mineral Admixture (CMA) as the replacement of the cement for each kind of concrete, were used in the study. Test results showed that the concrete with 30% CMA had the best properties compared with others both under standard-curing condition and steam-curing condition. Furthermore, the normal concrete (without CMA) and the high performance concrete (with 30% CMA) were chosen as the main materials in comparative tests to study the effect of curing conditions on the property of high performance concrete, such as the basic mechanical properties, the property against chloride penetration, and the property against carbonization. The results indicated that the curing temperature would increase the concrete strength in early age but not in long term. The curing condition would affect the property of concrete against carbonization but not the property of concrete against chloride penetration obviously.
Effect of Curing Regime on the Mechanical Strength, Hydration, and Microstructure of Ecological Ultrahigh-Performance Concrete (EUHPC)

Zhiwu Zuo,Jiachen Zhang,Beixing Li,Chuqi Shen,Gongfeng Xin,Xiao Chen

DOI: https://doi.org/10.3390/ma15051668

IF: 3.4

2022-02-23

Materials

Abstract:This paper investigates the effect of curing regimes (standard and steam curing) on the mechanical strength, hydration, and microstructure of ecological ultrahigh-performance concrete (EUHPC). The flowability, compressive strength, flexural strength, hydration, porosity, pore size distribution, and microstructure of UHPC with different contents of supplementary materials (silica fume, fly ash, and ground granulated blast furnace slag) were assessed. The test results showed that the compressive strength of EUHPC under steam curing was increased considerably compared to that under standard curing, while the flexural strength was mildly decreased. The steam curing could decrease the porosity of EUHPC, which ranged between 7% and 9% for standard curing, and between 3.5% and 5% for steam curing. The aperture of EUHPC was below 20 nm, mainly located in the range of 10 nm to 20 nm under standard curing, while it was less than 10 nm for steam curing. C–S–H gel was produced under steam curing, while unhydrated fly ash, mineral powder, and Ca(OH)2 crystal were observed in the amorphous C–S–H gel. The microstructure of EUHPC under steam curing was denser than that under standard curing, and the interfacial transition zones under both curing regimes were compact.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Effects of Steel Fiber and Specimen Geometric Dimensions on the Mechanical Properties of Ultra-High-Performance Concrete

Haozhen Fang,Mingen Gu,Shufeng Zhang,Haibo Jiang,Zhuangcheng Fang,Jiaxin Hu

DOI: https://doi.org/10.3390/ma15093027

IF: 3.4

2022-04-21

Materials

Abstract:Ultra-high-performance concrete (UHPC) is an advanced concrete with superior mechanical strength, ductility and durability properties. However, the influence of steel fiber on its constitutive laws and the specimen geometric dimension effect on its strength had not been paid enough attention. To investigate the effect of steel fibers on the properties of UHPC, specimens with different fiber volume contents and fiber types were tested. Meanwhile, the mechanical properties of UHPC at different ages from 3 days to 28 days were conducted. Moreover, specimens with various geometric dimensions were also prepared to study the effect of specimen geometric dimensions (dog-bone-shaped, prism and cylinder specimens) on the properties of UHPC. The results indicated that elastic modulus, tensile peak stress and the corresponding strain increased as the fiber volume content and curing age increased. Specimens with hooked-end fibers exhibited better tensile performance than those with straight fibers. Furthermore, different geometric dimensions of specimens significantly influenced the tensile properties of UHPC. Based on the experimental results, conversion factors were suggested for the transformation of strength obtained from specimens with different geometric dimensions to reference specimens. In addition, both compressive and tensile constitutive laws were proposed to generate the stress–strain relationship of UHPC.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Effects of alternating positive and negative temperature curing on the mechanical properties of ultra-high performance concrete

Jincen Guo,Zhixiang Zhou,Zhongya Zhang,Junhua Tang,Xin Li,Yang Zou

DOI: https://doi.org/10.1016/j.cscm.2023.e02752

IF: 4.934

2023-12-04

Case Studies in Construction Materials

Abstract:The Tibetan region is characterized by long winters and large diurnal temperature variations. Using prefabricated bridges combined with a small amount of cast-in-place concrete joints can address the challenging construction environment. To extend the bridge construction window for concrete in the joint, the performance of Ultra-High Performance Concrete (UHPC) under alternating positive and negative temperature environments was investigated. The effects of curing conditions (-10°C to 10°C and natural curing), different proportions of sulfoaluminate cement (0% / 6%), different concrete materials (UHPC/NC), and the presence of antifreeze admixtures on the macro-strength and late-stage microstructure of UHPC were explored. The results indicated that the slump expansion of the prepared UHPC in this study exceeds 600 mm. Alternating temperature environments significantly degrade the mechanical properties of UHPC without antifreeze admixtures. However, for self-made UHPC with antifreeze admixtures, the formed early structure can prevent freeze-thaw damage as long as the critical antifreeze strength is reached. After the temperature rebounded, the later-stage strength of UHPC can continue to develop and reach the compressive strength of samples that had not been exposed to low-temperature curing. The appropriate addition of sulfate aluminate cement positively affected the early compressive strength (1 day) and elastic modulus of UHPC. It also reduces the drying shrinkage of UHPC.

construction & building technology,materials science, multidisciplinary,engineering, civil
Effect of steel fiber distribution on the mechanical properties of UHPC caused by vehicle-bridge coupling vibration

Shunfeng Wang,Long Yu,Fei Yang,Linglin Xu,Kai Wu,Geert De Schutter,Zhenghong Yang

DOI: https://doi.org/10.1016/j.compositesb.2022.110201

2022-10-01

Abstract:With the acceleration of infrastructure construction, the risk of being exposed to vehicle-bridge coupling vibration is getting more common for the unhardened cementitious materials, which also intensifies the stress on the concrete and leads to the presence of micro-cracks at early age. In order to simulate vehicle-bridge coupling vibration in the actual construction sites, the properties and microstructure evolution of ultra-high performance concrete (UHPC) were evaluated systematically by fixing the specimens on an electric vibration table immediately after casting. The vibration parameters considered in this work involve the frequency and the amplitude according to the in-site monitor data. The heterogeneous distribution of air voids and steel fiber was determined by X-CT on cylindrical specimens with diameter of 70 mm and height of 100 mm quantitatively. In the early hydration, the position and distribution of steel fibers in the UHPC matrix could be able to move freely, which has significant impact on the mechanical properties. The compressive strength and drying shrinkage of UHPC specimens gradually increase with increasing the amplitude and frequency. However, a large amplitude and frequency would be detriment to the flexural and tensile strength due to changes in the angle and spatial distribution of steel fiber although the total porosity only varies slightly. Increasing amplitude and frequency promotes the presence of coarser air bubble and reduction of steel fibers inclination angle. This study is helpful for the design and application of UHPC in the actual construction sites, which could avoid the material failure during construction.
Analysis of the behavior of ultra high performance concrete at early age

Lin Wan,Roman Wendner,Benliang Liang,Gianluca Cusatis

DOI: https://doi.org/10.1016/j.cemconcomp.2016.08.005

IF: 9.93

2016-11-01

Cement and Concrete Composites

Abstract:Ultra high performance concretes (UHPCs) are cementitious composite materials with high level of performance characterized by high compressive strength, high tensile strength and superior durability. These are reached by a low water-to-binder ratio, optimized aggregate size distribution, thermal activation, and fiber reinforcement. In the past couple of decades, more and more UHPCs have been developed and found their ways into practice. Thus, the demand for computational models capable of describing and predicting relevant aging phenomena to assist design and planning is increasing. This paper presents the early age experimental characterization as well as the results of subsequent simulations of a typical UHPC matrix. Performed and simulated tests include unconfined compression, splitting (Brazilian), and three-point-bending tests. The computational framework is constructed by coupling a hygro-thermo-chemical (HTC) theory and a comprehensive mesoscale discrete model with formulated aging functions. The HTC component allows taking into account various types of curing conditions with varying temperature and relative humidity and predicting the level of concrete aging. The mechanical component, the Lattice Discrete Particle Model (LDPM), permits the simulation of the failure behavior of concrete at the length scale of major heterogeneities. The aging functions relate the mesoscale LDPM mechanical properties in terms of aging degree, defined in this work as the ratio between the quasi-static elastic modulus at a certain age and its asymptotic value. The obtained results provide insights into UHPC early age mechanisms yielding a computational model for the analysis of aging UHPC structures.

construction & building technology,materials science, composites
Study on the Dynamic Fracture Mechanical Properties of Ultra High-Performance Concrete under the Influence of Steel Fiber Content

Jun Zhang,Xiongfei Zhan,Zhenpeng Yu,Zili Dai,Xiaoqing Du

DOI: https://doi.org/10.1016/j.jobe.2024.110540

IF: 7.144

2024-01-01

Journal of Building Engineering

Abstract:Ultra-high performance concrete (UHPC) is characterized by its ultra-high strength and durability, making it suitable for use in large-span bridges, super high-rise buildings, and other special structures. These types of structures often have high requirements for crack control, making the exploration of UHPC's fracture mechanics properties of significant importance. Therefore, this paper sets up four steel fiber contents (0%, 0.6%, 1.2% and 1.8%) and four strain rates (10-5/s, 10-4/s, 10-3/s and 10-2/s), totaling 16 working conditions. The hydraulic servo system combined with digital image correlation (DIC) technology was used to conduct fracture mechanics tests on UHPC three-point bending beams. The test results show that the unstable fracture load of UHPC increases with the increase of strain rate and steel fiber content, and increasing the steel fiber content can enhance the strain rate effect of UHPC to a certain extent. Additionally, combined with the J-criterion model, this study proposed a dynamic criterion for the unstable fracture load of UHPC considering the influence of steel fiber content. The initial fracture toughness, unstable fracture toughness, and fracture energy of UHPC are significantly more affected by steel fiber content than by strain rate. Through DIC technology, the analysis of UHPC crack propagation shows that UHPC without steel fibers experiences rapid crack expansion in the Pre-90% to Peak stage, with less influence from the strain rate. However, UHPC with steel fibers exhibits a more uniform crack growth rate, with the crack emergence phase gradually lagging as the strain rate increases. For UHPC without steel fibers, the crack opening displacement (COD) at the unstable fracture load point surges suddenly, while the COD development in UHPC with steel fibers is slower. At lower strain rates, an increase in steel fiber content leads to an earlier sudden increase phase in UHPC's COD; at higher strain rates, the influence of steel fiber content on the sudden increase phase of UHPC's COD is more scattered. The research results of this paper provide a theoretical basis for the calculation and analysis of the dynamic response of UHPC structures under seismic loads.
A New Insight into the Design Compressive Strength of Ultra-High Performance Concrete

Masoud Pourbaba,Rajesh Chakraborty,Majid Pourbaba,Abdeldjelil Belarbi,Jung Heum Yeon

DOI: https://doi.org/10.3390/buildings13122909

IF: 3.324

2023-11-23

Buildings

Abstract:Compressive strength is one of the most critical mechanical properties of various types of concrete and is the main input variable for structural concrete design. Recently, with the advances in concrete technology, applications of fiber-reinforced concrete (FRC), including ultra-high performance concrete (UHPC), have grown rapidly. These new types of concrete are well known to exhibit superior mechanical characteristics such as compressive strength, fracture toughness, and durability compared to conventional concrete and thus are popularly used in urgent repair jobs where compressive strength is an important parameter to determine the required curing time until open to the public. Considering the importance of compressive strength in practice, this study aims to evaluate the effect of age and maturity on the compressive strength characteristics of three different types of concrete, namely UHPC with micro and macro steel fibers, FRC, and plain concrete, and to propose a new design strength criterion for UHPC. To this end, 180 concrete cube specimens were tested at 12 different ages between 3 and 126 days. The results indicated that irrespective of the type and presence of fibers, UHPC gained more than 90% of their ultimate compressive strength after only 21 days, while FRC and plain concrete specimens required a longer time (i.e., 28 days) to achieve 90% of their ultimate strength. Therefore, UHPC may adopt a 21-day compressive strength as a design input instead of a 28-day compressive strength commonly required for structural concrete specified by many codes of practice. Moreover, the obtained experimental results were compared with existing compressive strength predictive models in the codes of practice.

construction & building technology,engineering, civil
Early Age Shrinkage and Mechanical Effect of Ultra-High-Performance Concrete Composite Deck: A Case Study with In Situ Test and Numerical Simulation

Zhiguo Ma,Yue Li,Zhensheng Cao,Shaoqiang Zhang,Shengjun Hou,Jilin Liu,Xin Ruan

DOI: https://doi.org/10.3390/ma15103628

IF: 3.4

2022-05-20

Materials

Abstract:For the Honghe Bridge project located in Yunnan Province, Southwest China, a steel/ultrahigh-performance concrete (UHPC) composite deck is used in the suspension bridge with a 700 m main span, and the steel stud connectors are used in the 50 mm–thick UHPC layer. To investigate the shrinkage behavior of UHPC and the relevant influence, the in situ time-dependent strain is measured continuously, and within the 20-day curing time, the material behavior is summarized based on test results. This paper proposes a prediction model for UHPC shrinkage which is refined from the widely used B3 model for normal concrete material, and the parameter values are modified and optimized by experimental comparison. Combining the numerical model and the finite element analysis model of the composite deck, the detailed mechanical state in structural parts is studied. For the practical construction, the simulation results indicate that the small thickness of UHPC above the stud and weak bond strength can influence the eventual structural performance greatly. In the discussion of stress distribution at different locations of the deck, the potential crack on the edge and the corner of the UHPC–steel interface and the mechanical damage on the stud connector around are also indicated.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Cracking Performance in the Hogging-Moment Regions of Natural Curing Steel-UHPC and Steel-UHTCC Continuous Composite Beams

Jian-ping Lin,Linquan Lin,Zhongxin Peng,Rongqiao Xu,Guannan Wang

DOI: https://doi.org/10.1061/(ASCE)BE.1943-5592.0001820

2022-01-01

Journal of Bridge Engineering

Abstract:High-performance concretes without steam curing have great potential to improve crack resistance in the hogging-moment regions of continuous steel-concrete composite beams. This paper conducts experiments to investigate the cracking resistance of hogging-moment regions of prefabricated composite beams consisting of steel-NSCs (normal-strength concretes), natural curing steel-UHPCs (ultrahigh performance concretes), or steel-UHTCCs (ultrahigh toughness cementitious composites). The tensile strengths of natural curing UHPCs and UHTCCs are first measured because the concretes are usually in the tensile state in hogging-moment regions. Flexural tests are then conducted to investigate several important parameters of steel-NSC/-UHPC/-UHTCC composite beams: deflections, initial cracking loads, crack propagation, interlayer slips, and flexural bearing capacity. It is demonstrated that relative to traditional composite beams, steel-UHPC composite beams without steam curing can effectively improve the hogging-moment bending performance such as increasing cracking load, reducing interfacial slips, and concrete slab crack width. Moreover, it is found that although the steel-UHTCC composite beams are not as good as the steel-UHPC composite beams in terms of initial cracking loads but have better performance in controlling crack widths and lengths. The effect of prestressing on steel-UHPC composite beams under hogging moment is also studied and demonstrated to be influential in further increasing the cracking performance in hogging-moment regions.
Experimental Study of Flexural Performance of UHPC-NC Laminated Beams Exposed to Fire

Tieming Zhou,Xingwang Sheng

DOI: https://doi.org/10.3390/ma15072605

2022-04-01

Abstract:In recent decades, reinforced-concrete bridges have experienced premature deterioration and other problems during service due to severe environmental effects such as fire and corrosion. Previous studies have shown that the use of ultra-high-performance concrete (UHPC) can improve the durability of bridge structures. In this study, four-point bending tests were conducted on twelve UHPC-NC laminated beams with different UHPC-layer heights and at different temperatures in order to evaluate their flexural performance under fire conditions. The test variables were the UHPC heights (20 mm, 50 mm, 80 mm) and temperatures (20 °C, 200 °C, 400 °C, 600 °C), and the effects on the flexural load capacity of UHPC-NC laminated beams under the influence of these factors were investigated. The test results show that the increase in temperature causes the concrete color to change from grayish blue to white and leads to a significant decrease in the flexural load capacity of the stacked beams. The height of the UHPC layer has an important effect on the stiffness of the stacked beams and delays the formation of local cracks, thus improving the durability of the stacked beams.
High temperature and freeze-thaw study of strengthened concrete with ultra-high-performance concrete

Ming-Gin Lee,Wei-Chien Wang,Yung-Chih Wang,Yu-Cheng Kan,Shu-Lan Lin,Li-Chi Cheng

DOI: https://doi.org/10.1016/j.cscm.2024.e03339

IF: 4.934

2024-06-01

Case Studies in Construction Materials

Abstract:This study investigates the effectiveness of using ultra-high-performance concrete (UHPC) to strengthen concrete members subjected to high temperature and freeze-thaw conditions. Initially, the physical and mechanical properties of UHPC were examined. Subsequently, the durability of UHPC was evaluated through high temperature and freeze-thaw tests, assessing compressive strength, flexural strength, and splitting tensile strength. The study examined the reinforcing effects of different repair materials and thicknesses, including plain concrete and UHPC with varying fibre content. Results indicate that UHPC demonstrates high strength, ductility, and durability. However, under high temperature conditions exceeding 400°C for 2 hours, UHPC experienced bursting. Nonetheless, its strength remained relatively stable after 1000 freeze-thaw cycles, demonstrating excellent durability and resistance. Additionally, applying a 2-cm thickness of UHPC to strengthen concrete members resulted in significant retrofitting effects, enhancing the structural integrity of damaged buildings.

construction & building technology,materials science, multidisciplinary,engineering, civil
Spectrum of congenital heart disease detected echocardiographically in prenatal life.

L. Allan,D. Crawford,R. Anderson,M. Tynan

DOI: https://doi.org/10.1136/hrt.54.5.523

1985-11-01

Abstract:The spectrum of congenital heart disease seen in a series of 72 fetal anomalies detected echocardiographically differed from that seen in infancy. This reflects the selection of patients for referral for fetal echocardiography and the high rate of natural fetal loss that occurs when severe cardiac defects are present.
Compressive Strength Development of High-Volume Fly Ash Ultra-High-Performance Concrete under Heat Curing Condition with Time

Pham Sy Dong,Nguyen Van Tuan,Le Trung Thanh,Nguyen Cong Thang,Viet Hung Cu,Ju-Hyun Mun

DOI: https://doi.org/10.3390/app10207107

2020-10-13

Applied Sciences

Abstract:This research investigated the effect of fly ash content on the compressive strength development of ultra-high-performance concrete (UHPC) at different curing conditions, i.e., the standard curing condition and the heat curing. A total of 20 mixtures were prepared to cast specimens to measure the compressive strength at different ages from 3 days to 180 days. Additionally, 300 specimens were prepared to estimate the appropriate heat curing period at the early ages in terms of enhancing the 28-day compressive strength of UHPC with high content of fly ash (FA). From the regression analysis using test data, empirical equations were formulated to assess the compressive strength development of UHPC considering the FA content and maturity function. Test results revealed that the preference of the addition of FA for enhancing the compressive strength of UHPC requires the early heat curing procedure which can be recommended as at least 2 days under 90 °C. Moreover, the compressive strength of UHPC with FA under heat curing mostly reached its 28-day strength within 3 days. The proposed models based on the fib 2010 model can be a useful tool to reliably assess the compressive strength development of UHPC with high-volume fly ash (HVFA) (up to 70% fly ash content) under a heat curing condition that possesses a different performance from that of normal- and high-strength concrete. When 50% of the cement content was replaced by FA, the embodied CO2 emission for UHPC mixture reduced up to approximately 50%, which is comparable to the CO2 emission calculated from the conventional normal-strength concrete.
Mechanical and Drying Shrinkage Performance Study of Ultra-High-Performance Concrete Prepared from Titanium Slag under Different Curing Conditions

Jinxin Wang,Jun Li,Yan Gao,Zhongyuan Lu,Li Hou

DOI: https://doi.org/10.3390/ma17174201

IF: 3.4

2024-08-27

Materials

Abstract:This research investigates the effects of various curing regimes, the incorporation of titanium slag, and the utilization of quartz sand on the strength properties and shrinkage behavior of ultra-high-performance concrete (UHPC). By using low-heat silicate cement to prepare UHPC, this study conducted standard curing and steam curing, and comprehensively analyzed the macro and micro performance of UHPC under different curing conditions. The findings indicate that the application of steam curing markedly enhances the mechanical attributes of UHPC while efficiently decreasing its drying shrinkage. In the comparative tests, we found that the compressive strength of concrete that had undergone 2 days of steam curing was 9.15% higher than that of concrete cured for 28 days under standard conditions. In addition, under the same curing conditions, titanium slag sand had higher mechanical properties than quartz sand. Under standard curing conditions, the 28-day compressive strength of UHPC using titaniferous slag aggregate was 12.64% higher than that of UHPC using standard sand. Through the data analysis of XRD, TG, and MIP, we found that the content of Ca(OH)2 in the hydration products after steam curing was reduced compared to the standard curing conditions, and the pore structure had been optimized. The UHPC prepared with titanium slag sand has greater advantages in mechanical properties and drying shrinkage, and has a smaller pore structure than the UHPC prepared with quartz sand. Moreover, the use of titanium slag sand offers ecological and economic benefits, making it a more sustainable and cost-effective option for high-performance construction applications.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Study of ultra-high-performance concrete containing multivariate supplementary cementitious materials: experiments and modeling

Qidong Wang,Minghua Yang,Xudong Wang,Hongxin Liu,Changshun Zhou,Chenhui Jiang

DOI: https://doi.org/10.1080/1536383X.2023.2189239

IF: 2.06

2023-03-16

Fullerenes Nanotubes and Carbon Nanostructures

Abstract:In this paper, the effects of partial replacement of cement by metakaolin (MK) and different supplementary cementitious materials (SCMs) were investigated on the compressive strength and elasticity modulus of ultra-high-performance concrete (UHPC) at different ages, and the laws of the effects of MK alone, MK and conventional SCMs on the mechanical properties of UHPC were quantitatively analyzed at the macroscopic level. The results showed that the compressive strength of UHPC reached the maximum value when the MK doping amount reached 10%, and its compressive strength at 7, 28 and 90 days increased by 21%, 28% and 18.2%, respectively. Furthermore, the elasticity modulus of UHPC also showed a similar trend. When MK and Blast furnace slag or Fly ash were compounded, the mechanical properties (compressive strength and elasticity modulus) of UHPC were significantly enhanced in the later stage, showing sound synergistic effects. Based on the experimental test data, a model for predicting the elasticity modulus of UHPC based on the change of time and SCMs was proposed with good reliability.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology,physics, atomic, molecular & chemical
Influence and Mechanism of Curing Methods on Mechanical Properties of Manufactured Sand UHPC

Chengfang Yuan,Shiwen Xu,Ali Raza,Chao Wang,Di Wang

DOI: https://doi.org/10.3390/ma15186183

IF: 3.4

2022-09-06

Materials

Abstract:The mechanical properties of ultra-high performance concrete (UHPC) made of manufactured sand (MS) under four curing methods (steam, standard, sprinkler and saturated Ca(OH)2) were investigated via compressive, flexural and uniaxial tensile tests, and the bond strength of steel fiber and manufactured sand UHPC (MSUHPC) matrix. Based on the analysis of the microstructure, the influence mechanism of curing methods on the mechanical properties of materials was explored. The results showed that the early compressive strength of MSUHPC under steam curing (SM) is much higher than that of the other three curing methods, but the difference gradually decreases with the increase of age. The compressive strength of MSUHPC under SM is higher than that of river sand UHPC (RSUHPC). The bending strength and compressive strength of MSUHPC under different curing methods are similar, and the bending strength of 28 days steam cured samples is the highest. The uniaxial tensile properties of MSUHPC did not show significant difference under standard curing (SD), sprinkler curing (SP) and saturated Ca(OH)2 curing (CH), and the uniaxial tensile properties of MSUHPC under SM are slightly better than RSUHPC. The ultimate bond strength and fiber pullout energy of steel fiber and MSUHPC increase with the development of age. The bond strength and fiber pullout work of SM is higher than those of the other three curing methods, but there are lower increases in the later stage than that of the other three curing methods.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
The mechanism of curing regimes on the macroscopic properties and microstructure of ultra-high performance concrete with lightweight aggregates

Kai-zheng Guo,Gao-zhan Zhang,Yang Li,Jun Yang,Qing-jun Ding

DOI: https://doi.org/10.1016/j.jobe.2023.108236

IF: 7.144

2023-12-03

Journal of Building Engineering

Abstract:The internal curing effect of lightweight aggregates (LWA) enables ultra-high performance concrete (UHPC) to achieve lightweight and high-strength, but the performance and microstructure evolution mechanism of lightweight ultra-high performance concrete (L-UHPC) under different external curing regimes is still unclear. In this paper, L-UHPC was prepared using LWA from industrial waste, and the effect of water absorption of LWA on the properties of L-UHPC was investigated. Based on this, the evolution of performance and microstructure of L-UHPC under different curing regimes was investigated using nitrogen adsorption method, X-ray diffractometer, scanning electron microscope and nanoindentation techniques. The study shows that the best internal curing effect is achieved when the LWA is pre-wetted with water for 24 h. External thermal curing significantly improves the performance of L-UHPC, with dry heat curing having the best effect. The coupling effect of internal and external curing improves the density of the interface transition zone and reduces porosity, resulting in L-UHPC compressive strength >155 MPa and density <2100 kg/m 3 .

construction & building technology,engineering, civil
Age-dependent Size Effect and Fracture Characteristics of Ultra High Performance Concrete

Lin Wan,Roman Wendner,Gianluca Cusatis

DOI: https://doi.org/10.48550/arXiv.1608.08786

2016-09-14

Abstract:This paper presents an investigation of the age-dependent size effect and fracture characteristics of an ultra high performance concrete (UHPC). The study is based on a unique set of experimental data connecting aging tests for two curing protocols of one size and scaled size effect tests of one age. Both aging and size effect studies are performed on notched three point bending tests. Experimental data is augmented by state of the art simulations employing a recently developed discrete element based early-age computational framework. The framework is constructed by coupling a hygro-thermo-chemical (HTC) model and the Lattice Discrete Particle Model (LDPM) through a set of aging functions. The HTC component allows taking into account variable curing conditions and predicts the maturity of concrete. The mechanical component, LDPM, simulates the failure behavior of concrete at the length scale of major heterogeneities. After careful calibration and validation the mesoscale HTC-LDPM model is uniquely posed to perform predictive simulations. The ultimate flexural strengths from experiments and simulations are analyzed by the cohesive size effect curve (CSEC) method, and the classical size effect law (SEL). The fracture energies obtained by LDPM, CSEC, SEL, and cohesive crack analyses are compared and an aging formulation for fracture properties is proposed. Based on experiments, simulations, and size effect analyses, the age-dependence of size effect and the robustness of analytical size effect methods are evaluated.

Materials Science
XRD INVESTIGATIONS ON COMPRESSIVE STRENGTH GAIN OF UHPC SUBJECTED TO VARIOUS CURING TECHNIQUES

Aysha Haroon,T. Hemalatha

DOI: https://doi.org/10.14455/10.14455/isec.2022.9(1).mat-33

2022-06-01

Proceedings of International Structural Engineering and Construction

Abstract:Ultra High Performance Concrete (UHPC) is a relatively novel structural material which can be regarded as an advanced cementitious material with great stiffness, very high mechanical strength, and, extraordinary toughness in a broad sense. Even after cracking, the existence of tiny steel fibers confers the capacity to withstand deformations and, resist flexural and tensile stresses. Curing procedure is a key characteristic to enrich the qualities of the toughened concrete due to the inclusion of the mineral admixtures and a small water to binder ratio. If the process of curing is flawlessly completed, properties such as durability, volume stability, water tightness, strength, abrasion resistance, and resistance to freezing and thawing is highly enhanced. The impact of conventional water curing, hot air curing and, steam curing on the compressive strength of UHPC is explored in this study. UHPC cubes of side 70 mm are cast and the samples are subjected to water curing at 25°C, steam curing at 70°C temperature and, 75% RH and, hot air curing at 200°C. The cured samples are tested for compressive strength at different ages. The powders acquired after crushing the cubes are used for X-ray diffraction (XRD) studies. The variation in the compressive strength when subjected to different types of curing is analyzed using XRD studies, based on the products formed during hydration.

TRPM7 is required for ovarian cancer cell growth, migration and invasion.

Effect of Curing Conditions on Property of High Performance Concrete with Composite Mineral Admixture

Effect of Curing Regime on the Mechanical Strength, Hydration, and Microstructure of Ecological Ultrahigh-Performance Concrete (EUHPC)

Effects of Steel Fiber and Specimen Geometric Dimensions on the Mechanical Properties of Ultra-High-Performance Concrete

Effects of alternating positive and negative temperature curing on the mechanical properties of ultra-high performance concrete

Effect of steel fiber distribution on the mechanical properties of UHPC caused by vehicle-bridge coupling vibration

Analysis of the behavior of ultra high performance concrete at early age

Study on the Dynamic Fracture Mechanical Properties of Ultra High-Performance Concrete under the Influence of Steel Fiber Content

A New Insight into the Design Compressive Strength of Ultra-High Performance Concrete

Early Age Shrinkage and Mechanical Effect of Ultra-High-Performance Concrete Composite Deck: A Case Study with In Situ Test and Numerical Simulation

Cracking Performance in the Hogging-Moment Regions of Natural Curing Steel-UHPC and Steel-UHTCC Continuous Composite Beams

Experimental Study of Flexural Performance of UHPC-NC Laminated Beams Exposed to Fire

High temperature and freeze-thaw study of strengthened concrete with ultra-high-performance concrete

Spectrum of congenital heart disease detected echocardiographically in prenatal life.

Compressive Strength Development of High-Volume Fly Ash Ultra-High-Performance Concrete under Heat Curing Condition with Time

Mechanical and Drying Shrinkage Performance Study of Ultra-High-Performance Concrete Prepared from Titanium Slag under Different Curing Conditions

Study of ultra-high-performance concrete containing multivariate supplementary cementitious materials: experiments and modeling

Influence and Mechanism of Curing Methods on Mechanical Properties of Manufactured Sand UHPC

The mechanism of curing regimes on the macroscopic properties and microstructure of ultra-high performance concrete with lightweight aggregates

Age-dependent Size Effect and Fracture Characteristics of Ultra High Performance Concrete

XRD INVESTIGATIONS ON COMPRESSIVE STRENGTH GAIN OF UHPC SUBJECTED TO VARIOUS CURING TECHNIQUES