Parenting Education-Reply.

T. Boat,Marshall L. Land,L. Leslie

DOI: https://doi.org/10.1001/jamapediatrics.2017.5665

2018-04-01

JAMA Pediatrics

Abstract:

What problem does this paper attempt to address?

High Performance Liquid Chromatography Method for Residues Analysis of Thidiazuron in Apple and Soil

Ji-Ye Hu,Ya-Qin Hu,Yang Chen,Tao Yang

DOI: https://doi.org/10.1007/s00128-011-0383-z

2011-01-01

Bulletin of Environmental Contamination and Toxicology

Abstract:A rapid, sensitive and reliable analytical method for thidiazuron residues in apple and soil was established. The residual levels of the pesticide in apple and soil were determined by high performance liquid chromatography (HPLC) with UV detector. Samples of apple and soil were extracted with acetonitrile-water solutions, and then cleaned up by Florisil or C-18 cartridges. The results showed good linearity (r(2) = 1.000) over the concentration range of 0.01-5.0 mg/L. Limits of quantification (LOQ) of the method were 0.01 mg/kg for both soil and apple. Recovery from the apple and soil samples were 83.36%-84.08% and 85.27%-89.83%, respectively, and the corresponding relative standard deviations (RSDs) of the recovery data were 0.155%-0.524% and 0.475%-4.79% for the three fortified levels (0.01, 0.1, 0.5 mg/kg). The analyte in the samples were further confirmed by electrospray ionization tandem mass spectrometry (ESI-MS/MS). It was demonstrated that the proposed method was simple and efficient, and particularly suitable for detecting thidiazuron residues in apple and soil.
HPLC Determination of Atrazine in Surface Water with SPE Packed with Molecularly Imprinted Polymer

高会云,何娟,刘德仓,吕瑞鹤,卢奎

2009-01-01

Abstract:The molecularly imprinted polymer (MIP's) of atrazine was synthesized and packed into the SPE column which was used for separation and enrichment of atrazine from the water samples. Conditions for the MIP-SPE, including solvents used for sample introduction, for use as eluant and their amounts required, were studied and optimized. Water sample was introduced directly onto the MIP-SPE column, and rinsed with CH3OH-H2O(1+ 4). After drying the column by suction, atrazine on the column was eluted with methanol, which was collected and used for HPLC determination. Multiple of enrichment of atrazine by the proposed MIP-SPE attained to a value of 82. Linearity range for the determination was between 1 to 200μg · L-1 and the detection limit (3S/N) found was 0.5μg · L-1 Test for recovery was made at concentration levels of 10 μg · L-1 and 100μg · L-1 of atrazine added as standard solution, values of recovery found were 96.0% [RSD (n=6) 1.8%] and 97.2%,[RSD (n=6) 3.1%] respectively.
Preparation for Determination of Atrazine and Napropamide in Water,soil and Wheat

Jin Shefeng,Z. Y. You,Jiajun Zhang,Shao-Ming Ying,Hong Yang

2012-01-01

Abstract:Preparation methods for simultaneous determination of pesticides atrazine and napropamide in water,soil and wheat by high performance liquid chromatography(HPLC)were developed for the first time.Water samples were exacted,purified and collected by solid-phase extraction LC-18 column.Soil samples were extracted by acetone-water(3∶1,V/V)and purified and collected by solid-phase extraction LC-18 column.Wheat samples were extracted by acetone-water(3∶1,V/V),and the extraction solution was extracted by petroleum ether and purified and collected by solid-phase extraction LC-18 column.The calibration curves of the methods were determined in the range of 0.05-8.0 mg·L-1 of both atrazine and napropamide,with the correlation coefficients(R2)being 1.000 0 and 1.000 0 respectively.The methods gave the limit of detection(LOD)in 0.02 and 0.03 mg·L-1 for atrazine and napropamide.The average recoveries at the three spiked levels ranged from 96.13%-102.30% and 94.94%-101.33% for water sample with the relative standard deviations(RSD)of 2.3%-2.6% and 1.9%-2.9%,94.19%-103.14% and 97.84%-104.51% for soil sample with RSD of 0.2%-3.2% and 2.2%-6.2%,and 98.57%-107.44% and 86.98%-102.91% for wheat samples with RSD of 2.6%-3.2% and 0.5%-8.1%,respectively.
A Capillary Optical Biosensor for Rapid Detection of Atrazine Residue in Water and Beverages

Qian Sun,Xiao-Li Su,Jason Millett,Yanbin Li

DOI: https://doi.org/10.13031/2013.22877

2007-01-01

Abstract:Atrazine has been widely used in agriculture and horticulture for a long time, and it may cause severe environmental and reverse human health problems. Detection of atrazine residue is usually performed using chromatographic methods, such as GC and HPLC. These methods are reliable and have adequate sensitivity or detection limits required by regulatory standards, but they require expensive instruments, well-equipped laboratory and extensive sample preparation and/or pre-concentration. Therefore, there is an urgent need for rapid and cost-effective technologies to detect low levels of atrazine residue.
Determination of Carbofuran,Carbaryl and Atrazine in Water by SPE-HPLC

HE Xiao-min,GE Hong-bo,LI Ai-min,MA Xian-feng,SONG Guo-qiang

2011-01-01

Abstract:A method was established for determination of carbofuran,carbaryl and atrazine in water samples by solid phase extraction(SPE) and high performance liquid chromatograph(HPLC) using methanol-water as the mobile phase with gradient elution.The detection was made on a diode array detector at 220 nm.Dichloromethane was selected as eluting solvent.The results indicated that the good linear ranges were 0.200 mg/L～5.00 mg/L for carbofuran,and 0.020 mg/L～5.00 mg/L for carbaryl and atrazine.The detection limits of the method were 0.24 μg/L,0.019 μg/L and 0.035 μg/L for carbofuran,carbaryl and atrazine,respectively.The average recoveries of spiked standard materials at two quantity levels were from 84.0 % to 103%,and RSD was from 1.6% to 8.5%.
High-performance liquid chromatographic determination of the herbicide imazapyr residues in water and soil.

W Liu,A Pusino,C Gessa

DOI: https://doi.org/10.1016/0048-9697(92)90130-K

1992-01-01

Abstract:A rapid method for determining residues of the herbicide imazapyr in water and soil is described. The soil samples were extracted with aqueous methanol and, after concentrating, the residue was estimated by HPLC with UV detection at 250 nm. Imazapyr dissolved in water was quantified by injecting the samples without any previous treatments. Analyses were performed without clean-up of soil and water samples. The pre-concentration of samples was required only at very low herbicide amounts. The maximum recovery was achieved by methanol/water (3:2 v/v) with both soils after three extraction procedures. The detection limits were 0.01 mg/l and 0.05 mg/kg in water and soil, respectively.
Rapid Extraction and Determination of Atrazine and Its Degradation Products from Microporous Mineral Sorbents Using Microwave-Assisted Solvent Extraction Followed by Ultra-Hplc-ms/ms

Erdan Hu,Hefa Cheng

DOI: https://doi.org/10.1007/s00604-013-0971-1

IF: 5.7

2013-01-01

Microchimica Acta

Abstract:We have evaluated three methods for the extraction of atrazine and six of its degradation products from microporous mineral sorbents. Soxhlet extraction and ultrasonic extraction, which work well on soils and sediments, recover only <15 % of the atrazine from a dealuminated Y zeolite. Closed-vessel microwave-assisted extraction, in contrast, gives much better recoveries. This is attributed to the accelerated mass transfer at elevated temperatures and the displacement by the solvent forced into the mineral micropores under elevated pressures. Under the optimized conditions, the recovery of atrazine from the hydrophilic Y zeolites (Si/Al ratios <8) is almost quantitative, and ∼77 % for the more hydrophobic ones. The extraction efficiencies for the degradation products of atrazine in the hydrophilic zeolites (74.1–100 %) are also higher than those in the hydrophobic ones (22.3–44.2 %). The extracted compounds were quantified by a combination of ultra-HPLC and tandem MS and resulted in detection limits between 0.04 and 1.41 mg kg−1 on a hydrophilic Y zeolite (Si/Al = 2.55), and of 0.09–2.35 mg kg−1 on a hydrophobic zeolite (Si/Al = 15). The method was applied to study the degradation of atrazine sorbed on dealuminated Y zeolites.
Rapid residue analysis of four triazolopyrimidine herbicides in soil, water, and wheat by ultra-performance liquid chromatography coupled to tandem mass spectrometry

Xingang Liu,Jun Xu,Yuanbo Li,Fengshou Dong,Jing Li,Wenchen Song,Yongquan Zheng

DOI: https://doi.org/10.1007/s00216-010-4606-7

2011-01-08

Analytical and Bioanalytical Chemistry

Abstract:A sensitive and effective method for simultaneous determination of triazolopyrimidine sulfonamide herbicide residues in soil, water, and wheat was developed using ultra-performance liquid chromatography coupled with tandem mass spectrometry. The four herbicides (pyroxsulam, flumetsulam, metosulam, and diclosulam) were cleaned up with an off-line C18 SPE cartridge and detected by tandem mass spectrometry using an electrospray ionization source in positive mode (ESI+). The determination of the target compounds was achieved in <2.0 min. The limits of detection were below 1 μg kg−1, while the limits of quantification did not exceed 3 μg kg−1 in different matrices. Quantitation was determined from calibration curves of standards containing 0.05–100 μg L−1 with r2 > 0.997. Recovery studies were conducted at three spiked levels (0.2, 1, and 5 μg kg−1 for water; 5, 10, and 100 μg kg−1 for soil and wheat). The overall average recoveries for this method in water, soil, wheat plants, and seeds at three levels ranged from 75.4% to 106.0%, with relative standard deviations in the range of 2.1–12.5% (n = 5) for all analytes.

chemistry, analytical,biochemical research methods
Simultaneous Determination of Florfenicol with Its Metabolite Based on Modified Quick, Easy, Cheap, Effective, Rugged, and Safe Sample Pretreatment and Evaluation of Their Degradation Behavior in Agricultural Soils.

Mingfei Xu,Mingrong Qian,Hu Zhang,Junwei Ma,Jianmei Wang,Huizhen Wu

DOI: https://doi.org/10.1002/jssc.201400919

IF: 3.614

2014-01-01

Journal of Separation Science

Abstract:A simple and simultaneous method for the determination of florfenicol and its metabolite florfenicol amine in agricultural soils using modified quick, easy, cheap, effective, rugged, and safe sample pretreatment and reversed-phase high-performance liquid chromatography with tandem mass spectrometry is presented. Florfenicol and its metabolite florfenicol amine residues in agricultural soils were extracted with alkalized acetonitrile and an aliquot was cleaned up with Si(CH2)3NH(CH2)2NH2 and C18 sorbent, which were powder materials. High-performance liquid chromatography with tandem mass spectrometry was applied to simultaneously determine the level of florfenicol and florfenicol amine in agricultural soils. Excellent linearity was achieved for florfenicol and florfenicol amine over a range of concentrations from 0.1-500 μg/L with coefficients more than 0.99. Average recoveries at four different levels (0.005, 0.05, 0.5, and 5.0 mg/kg) for florfenicol and florfenicol amine ranged from 73.6-94.9% with relative standard deviations of 2.9-12.5%. The limits of detection for florfenicol and florfenicol amine in agricultural soils were 2.0 μg/kg, and the limits of quantification were 6.0 μg/kg. Based on this method, the degradation behavior of florfenicol and its metabolite florfenicol amine in three soils (Nanchang, Hangzhou, and Changchun) under sterilized and native conditions was investigated and the transformation rate of florfenicol amine from florfenicol was evaluated.
A surface-enhanced infrared absorption spectroscopy (SEIRA) multivariate approach for atrazine detection

Felipe C.S. Trindade,Izabel G. de Souza Sobrinha,Goreti Pereira,Giovannia A.L. Pereira,Ivo M. Raimundo,Claudete F. Pereira

DOI: https://doi.org/10.1016/j.saa.2024.124867

IF: 4.831

2024-07-26

Spectrochimica Acta Part A Molecular and Biomolecular Spectroscopy

Abstract:A green, fast and effective multivariate method for the determination of atrazine (ATZ) was developed using conventional infrared equipment furnished with an attenuated total reflectance module (ATR-IR), providing limit of detection (LOD) and limit of quantification (LOQ) in the ranges from 1.9 to 4.6 μg/mL and from 5.6 to 14 μg/mL, respectively. Furthermore, the surface-enhanced infrared absorption (SEIRA) approach was investigated to improve the sensitivity of the measurements and detect ATZ at low concentrations, addressing the compatibility with reference methods. To this end, a substrate formed by silver selenide quantum dots stabilized with mercaptopropionic acid (Ag 2 Se/MPA), synthesized in aqueous medium by an one-pot synthesis, was used. The spectral data were investigated by univariate and multivariate calibrations, allowing to calculate the enhancement factor (EF) and the multivariate enhancement factor (MEF), respectively. The SEIRA strategy proved to be able to enhance the atrazine signal up to 86-fold, allowing the detection of ATZ at concentrations as low as 0.001 μg/mL.

spectroscopy
Evaluation of different QuEChERS procedures for the recovery of selected drugs and herbicides from soil using LC coupled with UV and pulsed amperometry for their detection

Rosa Maria De Carlo,Luca Rivoira,Lorenzo Ciofi,Claudia Ancillotti,Leonardo Checchini,Massimo Del Bubba,Maria Concetta Bruzzoniti

DOI: https://doi.org/10.1007/s00216-014-8339-x

Abstract:Seven quick, easy, cheap, effective, rugged and safe (QuEChERS)-based procedures, differing in both the extraction and clean-up steps, were investigated for the recovery of bentazone (BTZ), atrazine (ATZ), carbamazepine (CBZ), phenytoin (PNT) and its metabolite 5-(p-hydroxyphenyl-),5-phenylhydantoin (HPPH) from soil. Target analytes were chosen for their extensive use and/or occurrence in soil, as well as for their medium-high polarity characteristics (log K OW values in the range 0.88-2.80), which have been reported as a critical parameter for the recovery from soil with QuEChERS approaches. Liquid chromatography coupled with UV and pulsed amperometric (PA) detection at a glassy carbon electrode was used as instrumental technique. The recovery data obtained within each tested procedure were discussed for each compound investigated, highlighting different behaviour depending on the specific physicochemical characteristics of the analytes. The optimized QuEChERS conditions consisted of the extraction of analytes with CH3CN:H2O 70:30, 5 % CH3COOH, followed by a dispersive solid-phase extraction (d-SPE) clean-up step with C18 sorbent. This method, in which water is directly added to the soil together with acetonitrile and salts, allowed the rehydration step to be avoided, which can be as long as 30 min. Matrix effects were evaluated for both the detection techniques at different concentration levels, and they were below 24 % for both the detection technique used. The recoveries were evaluated at three concentration levels by a matrix-matched calibration and were in the ranges of 83-113 % (relative standard deviations (RSD) ≤ 14 %) and 88-109 % (RSD ≤ 11 %) for UV and PA detection, respectively, highlighting very good performances of the method, even for the more polar analytes. Method detection limits ranged from 4 μg/kg (BTZ) to 493 μg/kg (PNT) and from 4 μg/kg (HPPH) to 11 μg/kg (BTZ) for UV and PA detection, respectively. The method was finally compared with a microwave-assisted extraction procedure which provided less satisfactory extraction performances than the optimized QuEChERS procedure.
A Portable Polymer‐based Sensor Platform for the Detection of Atrazine

Ionela Raluca Comnea‐Stancu,Jacobus (Koos) Frederick van Staden,Raluca‐Ioana Stefan‐van Staden

DOI: https://doi.org/10.1002/slct.202400757

2024-04-28

ChemistrySelect

Abstract:This study presents the development of an innovative, simple, and cost‐effective electrochemical sensing platform that comprises a portable system equipped with a poly‐8 ANDSA/CPE. The poly‐8‐ANDSA/CPE exhibited a linear relationship between the square wave voltammetric (SWV) peak current amplitude and ATZ concentration within 0.1–100 μM. The limit of detection for ATZ was determined to be 30 nM. Spiked recovery results of 97.71 % to 102.73 % with RSD (%) values less than 5 % validated the method's applicability for atrazine detection from water samples. Despite being banned by the European Union (EU), Atrazine, a synthetic herbicide, was found in Europe's coastal waters. Given the widespread ban on atrazine in many countries, it is imperative to perform screenings to detect its presence in food and water samples, as it poses significant risks to both human health and aquatic ecosystems. This study presents the development of an innovative, simple, and cost‐effective electrochemical sensing platform that comprises a portable system equipped with a poly‐8‐Amino‐1‐naphthol‐3,6‐disulfonic acid (8‐ANDSA) customized carbon paste electrode (CPE). The poly‐8 ANDSA/CPE was acquired using the process of electrochemical polymerization, utilizing cyclic voltammetry (CV) over the potential domain of −0.8 V to 1.8 V for 25 sweep cycles. The poly‐8‐ANDSA/CPE exhibited a linear relationship between the square wave voltammetric (SWV) peak current amplitude and ATZ concentration within 0.1–100 μM. The limit of detection for ATZ was determined to be 30 nM. Spiked recovery results of 97.71 % to 102.73 % with RSD (%) values less than 5 % validated the method's applicability for atrazine detection from water samples. The favorable outcomes indicated that the portable system performs exceptionally well and validates the practicality of ATZ detection, facilitating on‐site detection in actual water samples.

chemistry, multidisciplinary
Rapid Multi-Residue Method for Simultaneous Determination of 1,3,5-Triazine Herbicides in Environmental Samples by Capillary GC-MS-EI Selective Ion Monitoring Method

Perumal E. Ravi,Perumal E. Thirugnanam,Jothi Ramalingam Rajabathar,Hamad Al-Lohedan,S. Jenifer,Muthusamy Karnan

DOI: https://doi.org/10.3390/separations10060363

2023-06-18

Separations

Abstract:A new multi-residue method using gas chromatography–mass spectrometry electron ionization selective ion monitoring mode (SIM) has been developed for the simultaneous determination of eight 1,3,5-triazine herbicides such as 1,3,5-triazine-2,4-diamine (atrazine), ametryn, prometryn, propazine, terbuthylazine, terbutryn, and simazine simetryn in water and soil samples. Quantification is done using lindane (gamma benzene hexachloride) as an internal standard. A specific Capillary DB-Wax column of 30 m length, 0.32 mm internal diameter, and 0.25 μm film thickness is used for the separation of eight 1,3,5-triazine-2,4-diamine. The method was applied for the determination of residues in groundwater and soil samples. The lowest detection limit by GC-MS-SIM (selective ion monitoring mode) is 0.1 pg/mL. Recovery in water samples is in the range of 93–103%, and in soil samples, 91–102% for different individual compounds. Forty-five groundwater and soil samples were collected in and around Kancheepuram district in Tamilnadu (India), and they were analyzed for the respective residues. A detailed discussion of the GC-MS analysis results has been presented.

chemistry, analytical
Determination of Triazine Herbicides in Fruits and Vegetables Using Dispersive Solid-Phase Extraction Coupled with Lc-Ms

Feng Ji,Lixia Zhao,Wei Yan,Qinzhong Feng,Jin-Ming Lin

DOI: https://doi.org/10.1002/jssc.200700610

IF: 3.614

2008-01-01

Journal of Separation Science

Abstract:A simple, rapid, and sensitive liquid chromatography-mass spectrometry (LC-MS) method was successfully developed for the determination of three chloro-s-triazine herbicides, viz. atrazine, simazine, and propazine, two thiomethyl-s-triazine ones, viz. ametryn and prometryn, and prometon in fruits and vegetables. The instrumental parameters affecting LC separation and MS detection were investigated and the best conditions were selected. Samples were extracted and purified by dispersive solid-phase extraction (dispersive-SPE) with a primary-secondary amine sorbent. Three typical representative samples (luffa, broad bean, and grape) were selected to investigate the effect of different matrices on pesticide recoveries and assay precision after spiking at 0.05 mg/kg. Matrix composition did not interfere significantly with the determination of these pesticides. The recoveries were, with a few exceptions, in the range of 80-110% with relative standard deviations less than 10% (n = 5). In addition, this method was also applied to 21 different kinds of agriculture products collected from the local market, and two of the six triazines could be detected and quantified.
A new, simple, efficient and robust multi-residue method based on pressurised-liquid extraction of agricultural soils to analyze pesticides by liquid chromatography coupled with a high resolution quadrupole time-of-flight mass spectrometer

Giovanni Caria,Nicolas Proix,Christian Mougin,Baghdad Ouddane,Sopheak Net

DOI: https://doi.org/10.1080/03067319.2021.1889531

2021-02-23

International Journal of Environmental Analytical Chemistry

Abstract:A new method for the analysis of pesticides in agricultural soils by using liquid chromatography coupled with a high-resolution quadrupole time-of-flight mass spectrometer (LC-QTOF-MS) has been developed. Twenty-four pesticides including herbicides, insecticides or fungicides have been studied. The linearity of the external calibration of the pesticides obtained from levels of concentration ranging from 0.010 to 400 µg/Lgives satisfactory results with the correlation coefficients higher than 0.99. The quantification limits of the equipment range from 0.010 to 1.250 µg/L and correspond to the lowest standard in the calibration range for which the residual deviation is less than 60%. An experimental design has been used to optimise the parameters of pressurised-liquid extraction (PLE) of pesticides in soils. The optimised conditions have been found by using methanol as extraction solvent at a temperature of 80°C, a pressure of 150 Bars and 2 extraction cycles of 5 minutes. The mean recoveries of pesticides (Mean) are higher than 72% with a relative standard deviation(RSD) less than 21%. These results demonstrate the good efficiency of PLE for the extraction of pesticides in agricultural soils of different nature. The LC-QTOF-MS is a sensitive, linear and robust instrument for the quantification of pesticides in unpurified soil extracts by external calibration. This analytical tool is not subjected to matrix effects of soil extracts.

chemistry, analytical,environmental sciences
Determination of avermectin in pharmaceutical wastewater by rapid resolution liquid chromatography-tandem mass spectrometry

LI Zaixing,WU Chunxu,ZHANG Jingxuan,LI Hui,JU Panpan,YU Xin

DOI: https://doi.org/10.13671/j.hjkxxb.2011.09.025

2011-01-01

Abstract:A method based on solid phase extraction-rapid resolution liquid chromatography-tandem mass spectrometry(SPE-RRLC-MS/MS) was developed to determine avermectin in pharmaceutical wastewater.Water samples were firstly purified through centrifugation and protein precipitation processes,and then the avermectin was enriched and purified with HLB SPE,separated through Agilent Plus C18 RRLC(rapid resolution liquid chromatography) using 0.1% formic acid solution and 50% to 90% methanol as mobile phase,and detected by mass spectrometry in positive ion mode with multiple reaction monitoring(MRM) using an electrospray ionization interface.The detection limit was 0.5 μg·L-1.The linear range was 0.1 μg·L-1 to 20 μg·L-1,with a coefficient of determination of 0.997.The recoveries at spiked concentrations of 0.1 μg·L-1,0.5 μg·L-1 and 4.0 μg·L-1 ranged from 73.31% to 111.03%,with a relative standard deviation(RSD) from 4.97% to 9.37%.The procedure provides a rapid,reliable and sensitive method for determination of avermectin in pharmaceutical wastewater.
Uptake and Removal Efficiency of Atrazine in Soil by Several Weeds

CHEN Jian-jun,LI Ming-rui,ZHANG Kun,LI Yuan

DOI: https://doi.org/10.11654/jaes.2014.12.013

2014-01-01

Abstract:Atrazine was the most commonly detected herbicide contaminating soil and water. Phytoremediation has been approved to a cost-effective technique. In this study, a pot experiment was carried out to compare the uptake and removal efficiency of atrazine in soil by seven weeds. Enrichment and transfer characteristics of atrazine in plants as well as relationships between the removal efficiency of atrazine and plant biomass, root growth were also investigated. Growing plants profoundly improved the removal efficiency of atrazine from soil. Compared with the control, the highest removal efficiency of atrazine was found in Pennisetum hydridumn with the removal efficiency being increased by 40.37%. The removal efficiency of atrazine was in order of P. hydridum﹥Saccharum arundinaceum﹥Lolium perenne L.﹥Festuca elata﹥Solanum nigrum L.﹥Gramineae﹥C. rotundus, and was significantly positively correlated with plant biomass(r=0.838)and ratio of root to shoot biomass(r=0.866). Seven weed plants did show absorption, enrichment and transfer of atrazine to some extents. The enrichment co-efficient and transfer coefficient of P. hydridum was the highest, which were 0.54 and 2.81, respectively, followed by those of S. arundi-naceum and F. elata. In sum, P. hydridum, S. arundinaceum and F. elata could be recommended for restoring atrazine contaminated soils.
Isotope fractionation of micropollutants during large-volume extraction: heads-up from a critical method evaluation for atrazine, desethylatrazine and 2,6-dichlorobenzamide at low ng/L concentrations in groundwater

Aileen Melsbach,Denis Pittois,Michael Bayerle,Martina Daubmeier,Armin H. Meyer,Kathrin Hölzer,Tom Gallé,Martin Elsner

DOI: https://doi.org/10.1080/10256016.2020.1812599

IF: 1.667

2020-09-24

Isotopes in Environmental and Health Studies

Abstract:Micropollutants are frequently detected in groundwater. Thus, the question arises whether they are eliminated by natural attenuation so that pesticide degradation would be observed with increasing residence time in groundwater. Conventional analytical approaches rely on parent compound/metabolite ratios. These are difficult to interpret if metabolites are sorbed or further transformed. Compound-specific stable isotope analysis (CSIA) presents an alternative for identifying degradation based on the analysis of natural isotope abundances in pesticides and their changes during degradation. However, CSIA by gas chromatography–isotope ratio mass spectrometry is challenged by the low concentrations (ng/L) of micropollutants in groundwater. Consequently, large amounts of water need to be sampled requiring enrichment and clean-up steps from interfering matrix effects that must not introduce artefacts in measured isotope values. The aim of this study was to evaluate the accuracy of isotope ratio measurements of the frequently detected micropollutants atrazine, desethylatrazine and 2,6-dichlorobenzamide after enrichment from large water volumes (up to 100 L) by solid-phase extraction with consecutive clean-up by HPLC. Associated artefacts of isotope discrimination were found to depend on numerous factors including organic matter content and extraction volume. This emphasizes the necessity to perform a careful method evaluation of sample preparation and sample pre-treatment prior reliable CSIA.

environmental sciences,chemistry, inorganic & nuclear
Quantitation of glyphosate, glufosinate, and AMPA in drinking water and surface waters using direct injection and charged-surface ultra-high performance liquid chromatography-tandem mass spectrometry

Alistair K Brown,Annemieke Farenhorst,Alistair K. Brown

DOI: https://doi.org/10.1016/j.chemosphere.2023.140924

IF: 8.8

2024-02-01

Chemosphere

Abstract:Herbicides glyphosate (N-(phosphonomethyl)glycine) and glufosinate (2-amino-4-(hydroxymethylphosphinyl)butanoic acid) and the main transformation product of glyphosate, aminomethanephosphonic acid (AMPA), are challenging to analyze for in environmental samples. The quantitative method developed by this study adapts previously standardized dechlorination procedures coupled to a novel charged surface C18 column, ultra-high performance liquid chromatography-tandem mass spectrometry, polarity switching, and direct injection. The method was applied to chlorinated tap water, as well as river samples, collected in the City of Winnipeg and rural Manitoba, Canada. Using only syringe filtration without derivatization, the validated method resulted in good accuracies in both tap and surface water, at both 2 and 20 μg L-1. Method limits of detection (MLD) and quantification (MLQ) ranged from 0.022/0.074 to 0.11/0.36 μg L-1, with precisions of 0.46-2.2% (intraday) and 1.3-7.3% (interday). The mean (SEM) of the pesticides in μg L-1 for tap water were 0.11 (0.007) (AMPA), glufosinate and glyphosate < MLDs; and for Red River water were 0.56 (0.045) (AMPA), glufosinate < MLQ, and glyphosate 0.40 (0.072). For the smaller tributaries, glufosinate was >MLD but < MLQ once and that was for Shannon Creek at 0.2 μg L-1. For the remaining rivers, the mean concentrations ranged from 0.31 to 3.1 μg L-1 for AMPA, and 0.087-0.53 μg L-1 for glyphosate. The method will be ideal for supporting monitoring and risk assessment programs that require high throughput sampling and quantitative methods capable of producing robust results that leverages chromatographic and mass spectrometric paradigms instead of being extraction technology focused.

environmental sciences
Possibilities and Limitations of Isocratic Fast Liquid Chromatography-Tandem Mass Spectrometry Analysis of Pesticide Residues in Fruits and Vegetables

Steven J. Lehotay

DOI: https://doi.org/10.1007/s10337-018-3595-0

2018-08-25

Chromatographia

Abstract:Currently, state-of-the-art analytical methods for multiclass, multiresidue monitoring of pesticides in foods use ultrahigh performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) for analysis of LC-amenable analytes. UHPLC-MS/MS for > 100 pesticides typically takes 10 min per injection using gradient elution in the reversed-phase mode, plus typically 3–5 min for re-equilibration between injections. Isocratic mobile-phase conditions eliminate need for the re-equilibration, and can greatly speed analysis time. In this study, fast isocratic LC-MS/MS was evaluated using a C18 analytical column of 3 cm × 4.6 mm i.d. with 3 µm particles and a mobile phase consisting of 10 mM ammonium formate at pH 3 in 47.5/47.5/5 (v/v/v) acetonitrile/methanol/water. Flow rate was 0.4 mL/min and injection volume was 50 µL. Sample preparation entailed a formate-buffered QuEChERS method for fruit and vegetable samples, typically yielding extract of 1.27 g/mL sample equivalent in 94/6 acetonitrile/water without additional cleanup. The analysis time was 2.6 min covering 88 diverse pesticide analytes each with three ion transitions (dwell times of 5 ms and 5 ms interscan delays). Validation experiments involving fortification of water, pear, tomato, cucumber, eggplant, and cilantro at 10 and 100 ng/g (n = 10 for each matrix and level) showed that the method achieved acceptable quantification with 70–120% recoveries and ≤ 25% RSD for 32–62 (36–70%) of the analytes depending on the matrix. Using regulatory identification criteria, only 6 false positives occurred above 10 ng/g among 4400 analyte/matrix/sample combinations, but false negatives varied depending on the pesticide/matrix pair, with results improving significantly for analytes with retention times > 1.3 min. This study demonstrated the feasibility and limits of isocratic LC-MS/MS for rapid screening of common commodities monitored for pesticide residues.Graphical Abstract

chemistry, analytical,biochemical research methods

Parenting Education-Reply.

High Performance Liquid Chromatography Method for Residues Analysis of Thidiazuron in Apple and Soil

HPLC Determination of Atrazine in Surface Water with SPE Packed with Molecularly Imprinted Polymer

Preparation for Determination of Atrazine and Napropamide in Water,soil and Wheat

A Capillary Optical Biosensor for Rapid Detection of Atrazine Residue in Water and Beverages

Determination of Carbofuran,Carbaryl and Atrazine in Water by SPE-HPLC

High-performance liquid chromatographic determination of the herbicide imazapyr residues in water and soil.

Rapid Extraction and Determination of Atrazine and Its Degradation Products from Microporous Mineral Sorbents Using Microwave-Assisted Solvent Extraction Followed by Ultra-Hplc-ms/ms

Rapid residue analysis of four triazolopyrimidine herbicides in soil, water, and wheat by ultra-performance liquid chromatography coupled to tandem mass spectrometry

Simultaneous Determination of Florfenicol with Its Metabolite Based on Modified Quick, Easy, Cheap, Effective, Rugged, and Safe Sample Pretreatment and Evaluation of Their Degradation Behavior in Agricultural Soils.

A surface-enhanced infrared absorption spectroscopy (SEIRA) multivariate approach for atrazine detection

Evaluation of different QuEChERS procedures for the recovery of selected drugs and herbicides from soil using LC coupled with UV and pulsed amperometry for their detection

A Portable Polymer‐based Sensor Platform for the Detection of Atrazine

Rapid Multi-Residue Method for Simultaneous Determination of 1,3,5-Triazine Herbicides in Environmental Samples by Capillary GC-MS-EI Selective Ion Monitoring Method

Determination of Triazine Herbicides in Fruits and Vegetables Using Dispersive Solid-Phase Extraction Coupled with Lc-Ms

A new, simple, efficient and robust multi-residue method based on pressurised-liquid extraction of agricultural soils to analyze pesticides by liquid chromatography coupled with a high resolution quadrupole time-of-flight mass spectrometer

Determination of avermectin in pharmaceutical wastewater by rapid resolution liquid chromatography-tandem mass spectrometry

Uptake and Removal Efficiency of Atrazine in Soil by Several Weeds

Isotope fractionation of micropollutants during large-volume extraction: heads-up from a critical method evaluation for atrazine, desethylatrazine and 2,6-dichlorobenzamide at low ng/L concentrations in groundwater

Quantitation of glyphosate, glufosinate, and AMPA in drinking water and surface waters using direct injection and charged-surface ultra-high performance liquid chromatography-tandem mass spectrometry

Possibilities and Limitations of Isocratic Fast Liquid Chromatography-Tandem Mass Spectrometry Analysis of Pesticide Residues in Fruits and Vegetables