Abstract:Statement of problem: The accuracy of digital waxing-guided trial restoration protocols that have been implemented with ceramic veneers has not been reported. Purpose: The purpose of this in vitro study was to evaluate the accuracy of 3 digital trial restorations fabricated from digital waxing for ceramic veneers. Material and methods: A uniform 0.3-mm digital waxing added to the facial surface of 30 maxillary central typodont incisors was created in a software program. The trial restorations were fabricated on typodont teeth with autopolymerizing acrylic resin by using a silicone index based on 3-dimensionally printed casts designed from the digital waxing. The 30 maxillary central incisors were divided into 3 groups: the depth cutter (0.5 mm, Komet) (DC) group, the round bur (1.5 mm, Diatech) (RB) group, and the specially designed calibrated depth bur (laser mark of 0.5 mm, Gaofeng) (CD) group. The 3 groups were randomly prepared with a random number table by 2 experienced prosthodontists aiming to produce an even facial clearance of 0.5 mm. The dimensional differences in the standard tessellation language (STL) files between the surfaces of the original teeth, digital waxing, trial restorations, and prepared teeth in the software program were measured and analyzed at the same 9 points on the labial surface. One-way ANOVA with a post hoc test was used to identify significant discrepancies between trial restorations and waxing and differences in the reduction depth of typodont teeth (RDT) and the reduction depth (RD) among the 3 techniques (α=.05). The mean relative differences (MRDs) were calculated to determine the accuracy (%). Results: The thickness of the trial restorations was significantly greater than that of the digital waxings, with a discrepancy of 0.20 ±0.14 mm, especially at the cervical site. With the use of a trial restoration, the RDTs of the middle (-0.01 ±0.11 mm) and cervical locations (0.09 ±0.20 mm) showed significantly smaller preparation depths than did the other locations. Significant differences in RD were found among the 3 guided techniques (P<.05). Group DC presented the most accurate result of 0.51 ±0.08 mm with an MRD of 2%, whereas the results of 0.57 ±0.10 mm with an MRD of 14% and 0.60 ±0.11 mm with an MRD of 20% were obtained from group RB and group DC, respectively. Conclusions: The trial restoration was significantly thicker than its corresponding waxing. The DC technique presented the most accurate reduction result among the 3 protocols examined.

Dentin Exposure after Tooth Preparation for Laminate Veneers: A Microscopical Analysis to Evaluate the Influence of Operators' Expertise

Evaluation of the ceramic laminate veneer-tooth interface after different resin cement excess removal techniques

Comparing Marginal Microleakage of Three Different Dental Materials in Veneer Restoration Using a Stereomicroscope: an in Vitro Study.

3D Evaluation of Accuracy of Tooth Preparation for Laminate Veneers Assisted by Rigid Constraint Guides Printed by Selective Laser Melting.

Stress distribution on teeth restored with veneers using various incisal preparation designs: A 3D finite element analysis study

Prophylometric and SEM analyses of four different finishing methods

Comparative Evaluation of Two Different Preparation Designs and Materials on the Fracture Resistance of Laminate Veneers: An In Vitro Study

Influence of Operator, Tool, Dental Loupes, and Tooth Position on Enamel Loss and Composite Remnants After Removal of Composite Attachments for Orthodontic Clear Aligners: An Experimental Study Using 3D Profilometry

A Light Microscopic Study Comparing Pulp Histological Alterations Following Tooth Preparation Using a High-speed Handpiece and an Er: YAG Laser

Comparative Study Of Electric Handpiece And Air-Turbine Handpieces After Tooth Prepare For Veneer

Analysis of Edge Morphology of Partial Veneers Made by Different Processing Techniques and Materials

The effect of veneer on the marginal fit of the copings using different materials

A comparative evaluation of marginal fit and microleakage of computer-aided design/computer-aided manufacturing-milled zirconia and prefabricated posterior occlusal veneers: An in vitrostudy

Accuracy of three digital waxing-guided trial restoration protocols for controlling the depths of tooth preparation for ceramic veneers

[Morphology accuracy evaluation of direct composite occlusal veneer using two types of modified stamp-technique]

Investigation on the Effectiveness of Digital Scanning Combined with Reverse Engineering Technology in Demonstrating Full Crown Tooth Preparation

Comparison of the Marginal and Internal Fit of Ceramic Laminate Veneers Fabricated with Four Different Computer-Aided Manufacturing Techniques

Effect of Tooth Preparation Design on Marginal Adaptation of Composite Resin CAD-CAM Onlays

Effect of preparation design and scan pattern on the accuracy of intraoral scans for complete arch laminate veneers under simulated intraoral variables

Comparison of Two Post Preparation Methods in Mandibular Second Molars with a C-shaped Root Canal Configuration.

Marginal, internal fit and microleakage of zirconia infrastructures: an in-vitro study