[Problems in hemolytic anemias with pyruvate kinase deficiency. I. Clinical and hematologic picture in 4 patients].

V. Brabec,G. Jacobasch,J. Janele,B. Friedmann

1983-05-01

Abstract:

What problem does this paper attempt to address?

A Reconfigurable Convolution-in-Pixel CMOS Image Sensor Architecture

Ruibing Song,Kejie Huang,Zongsheng Wang,Haibin Shen

DOI: https://doi.org/10.1109/tcsvt.2022.3179370

IF: 5.859

2022-01-01

IEEE Transactions on Circuits and Systems for Video Technology

Abstract:The separation of the data capture and analysis in modern vision systems has led to a massive amount of data transfer between the end devices and cloud computers, resulting in long latency, slow response, and high power consumption. Efficient hardware architectures are under focused development to enable Artificial Intelligence (AI) at the resource-limited sensing devices. One of the most promising solutions is to enable Processing-in-Pixel (PIP) scheme. However, the conventional schemes suffer from the low fill-factor issue. This paper proposes a PIP based Complementary Metal-Oxide-Semiconductor (CMOS) sensor architecture, which allows convolution operation before the column readout circuit to significantly reduce the overall power consumption while improving the resource utilization of the succeeding deep learning accelerator. The simulation results show that the proposed architecture could support the computing efficiency up to 3.37 TOPS/W at the 8-bit weight configuration, which is four times as high as the conventional schemes after normalization. The transistors required for each pixel are only 3.5T, significantly improving the fill-factor.
A Two-Tap Indirect Time-of-Flight CMOS Image Sensor With Pump Gate Modulator for Low-Power Applications

Bing Zhang,Congzhen Hu,Junhua Lai,Youze Xin,Zhuoqi Guo,Zhongming Xue,Li Dong,Chi Wang,Shuyu Lei,Guohe Zhang,Li Geng

DOI: https://doi.org/10.1109/ted.2021.3123045

IF: 3.1

2021-01-01

IEEE Transactions on Electron Devices

Abstract:A 320 $\times $ 240 indirect time-of-flight (i-ToF) image sensor with a 5.6-$\mu \text{m}$ two-tap 1.5-V pump gate modulation pixel has been designed. Novel characteristics, such as the optimized pinned layer doping and potential buffer region (PBR) structure with pump gate modulator (PGM), are proposed to achieve a maximum lateral modulation electric field of 1500 V/cm under the front-side illumination (FSI) process. As a result, the proposed time-of-flight (ToF) sensor shows 200-mW power consumption and 54% demodulation contrast (DC) at 50-MHz modulation frequency, depth noise less than 1% with 940-nm illuminator from 0.3 to 3 m.

engineering, electrical & electronic,physics, applied
A 0.18 Μm High Resolution Bandpass Delta-Sigma Modulator for Acceleration Transducer Applications

Cao Tianlin,Han Yan,Zhang Shifeng,Han Xiaoxia,Chen Yaya

DOI: https://doi.org/10.1109/icsict.2016.7999072

2016-01-01

Abstract:This paper presents a low-power high-resolution band-pass ΔΣ modulator for acceleration transducer applications. The proposed band-pass ΔΣ modulator consists of a high-performance 6 th order feed-forward ΔΣ modulator with 1-bit quantization. The modulator is fabricated in 0.18 μm 1P6M CMOS process with a core area of 1.47 mm 2 . This modulator got 90.3 dB peak signal to noise plus distortion ratio(SNDR) and 97 dB dynamic range(DR) over 4-kHz bandwidth, while the intermediate frequency(IF) is shifting from 100 KHz to 200 KHz. The power dissipation is 5 mW under 3.3-V power supply.
Transverse Dynamic Modulation Transfer Function of Subpixel Push-Scanning Imaging by Linear CCD

WANG Ling,XU Zhi-hai,FENG Hua-jun,LI Qi

DOI: https://doi.org/10.3785/j.issn.1008-973x.2008.02.027

2008-01-01

Abstract:Subpixel imaging technique can reconstruct a new image whose resolution is twice times higher than the original images obtained by two CCDs with 1/2 pixel shift.The relative shift between the images and the CCD attributing to the high speed movement of an object degenerates the image quality.By introducing the velocity of relative movement into the model,the transverse dynamic modulation transfer function(MTF) of subpixel push-scanning CCD imaging was deduced from the definition of MTF.The results of numerical computation for the MTF of a CCD sensor show that the subpixel imaging technique can improve the transverse imaging quality of the linear push-scanning CCDs.
A Time-to-Digital Converter for Low-Power Consumption Single Slope Analog-to-Digital Converters in a High-Speed CMOS Image Sensor

Ziyi Li,Zhiyuan Gao

DOI: https://doi.org/10.3390/mi15050578

IF: 3.4

2024-04-28

Micromachines

Abstract:To reduce the power consumption of a TDC in high-speed applications, a TDC architecture applied to SS ADC is proposed to reduce redundant counting. This structure can remove the identical part between two rows of pixel signals in a CMOS image sensor by adjusting the start and stop signal of the TDC, which will reduce the number of flipping of D flip-flops in the TDC. This structure requires the simultaneous readout of two rows of pixels in the high-speed CMOS image sensor. In the 110 nm CMOS process, simulation results show that the designed 5-bit TDC achieves an effective number of bits (ENOB) at 4.72 bits and a figure-of-merit (FOM) at 104.7–162.3 fJ/step, with a power consumption ranging from 60 μW to 93 μW. Compared with traditional counting methods, the proposed TDC can reduce counting power consumption by 30%.

chemistry, analytical,nanoscience & nanotechnology,instruments & instrumentation,physics, applied
Identification of a Novel Abscisic Acid-Regulated Farnesol Dehydrogenase from Arabidopsis1[W][OA]

J. Bhandari,A. Fitzpatrick,D. Crowell

DOI: https://doi.org/10.1104/pp.110.157784

IF: 7.4

2010-08-31

PLANT PHYSIOLOGY

Abstract:In Arabidopsis (Arabidopsis thaliana), farnesylcysteine is oxidized to farnesal and cysteine by a membrane-associated thioether oxidase called farnesylcysteine lyase. Farnesol and farnesyl phosphate kinases have also been reported in plant membranes. Together, these observations suggest the existence of enzymes that catalyze the interconversion of farnesal and farnesol. In this report, Arabidopsis membranes are shown to possess farnesol dehydrogenase activity. In addition, a gene on chromosome 4 of the Arabidopsis genome (At4g33360), called FLDH, is shown to encode an NAD+-dependent dehydrogenase that oxidizes farnesol more efficiently than other prenyl alcohol substrates. FLDH expression is repressed by abscisic acid (ABA) but is increased in mutants with T-DNA insertions in the FLDH 5′ flanking region. These T-DNA insertion mutants, called fldh-1 and fldh-2, are associated with an ABA-insensitive phenotype, suggesting that FLDH is a negative regulator of ABA signaling.
6.9 A 0.35V 0.367TOPS/W Image Sensor with 3-Layer Optical-Electronic Hybrid Convolutional Neural Network

Xuecheng Wang,Zheng Huang,Tianyi Liu,Wanxin Shi,Hongwei Chen,Milin Zhang

DOI: https://doi.org/10.1109/isscc49657.2024.10454479

2024-01-01

Abstract:Traditional computer-vision technology that relies on image sensors coupled with cloud processing or on-chip Artificial Intelligence (AI) processors have encountered significant challenges in terms of power consumption, delays arising from data transmission, and/or memory access. In-sensor and near-sensor computing have been reported to solve this issue by applying pixel or array level feature extraction [2–6]. In [2, 4], capacitors are utilized for analog-domain Haar filtering to reduce the processing power consumption, but sacrificing the Fill Factor (FF) due to the use of the capacitor array [2], or complicated pixel-level logic [4]. An image sensor in introduced in [3] with Hog feature-based object detection, achieving both low power and high accuracy for the detection of up to three object classes. However, it does not work on more complex tasks. Convolutional Neural Networks (CNNs) [5, 6] offer enhanced accuracy in practical applications, but increase the power consumption and circuit complexity. Optical-domain processing [7] is capable of parallel information processing through an optical architecture based on free space. However, in [7] this is based on diffraction and requires coherent light as input, which constrains the practicality for edge computing. This paper presents a Pulse Width Modulation (PWM) pixel-based image sensor array that integrates an optical-electronic hybrid 3-layer convolutional processing unit. The first layer of the convolution is performed in the optical domain without introducing extra power consumption. The integration of optical convolution with electrical convolution offers the potential to leverage the energy-efficient advantages of optical convolution, while simultaneously providing the essential programmability needed to address multiple use-cases through reprogramming within a single device. A dual-mode Processing Element (PE) is proposed enables both acquisition mode and calculation mode. The integration of a sum/differential dual-counter design and the incorporation of two different pixel reset methods are employed in the co-design of PWM pixels and PEs to effectively mitigate computational power consumption.
A low power 10‐bit 1 MS/s cyclic analog to digital converter for complementary metal oxide semiconductors image sensors with comparator‐based switched‐capacitor technique

Ziyang Zhang,Kaiming Nie,Dongxing Fang,Jiangtao Xu

DOI: https://doi.org/10.1002/cta.4060

IF: 2.378

2024-05-10

International Journal of Circuit Theory and Applications

Abstract:This paper proposes a power‐optimised column‐parallel cyclic ADC for CMOS image sensor readout circuits. The design combines a 2.5‐bit/cycle architecture with a comparator shutdown technique based on the Comparator‐Based Switched Capacitor (CBSC) circuits, which reduces the operating time of the threshold detection comparator compared to conventional CBSC circuits. This paper proposes a power‐optimized column‐parallel cyclic analog to digital converter (ADC) for complementary metal oxide semiconductors (CMOS) image sensor readout circuits. The design combines a 2.5‐bit/cycle architecture with a comparator shutdown technique based on the comparator‐based switched‐capacitor (CBSC) circuits, which results in a significant reduction in the operating time of the threshold detection comparator compared with conventional CBSC circuits. This reduction in operating time leads to power savings as the threshold detection comparator can be shut down quickly. The paper also presents a comprehensive analysis of the nonideal factors of CBSC circuits and the coarse and fine conversion allocation scheme. The 10‐bit two‐stage comparator‐based cyclic ADC is designed in a 110 nm 1P4 M CMOS technology. Simulation results show that the effective number of bit (ENOB) is 9.7 bits, with each column consuming 103 μ W of power. The proposed cyclic ADC has a figure of merit (FOM) of 123 fJ/conv‐step. Compared with conventional structures, the proposed design reduces the power consumption of the ADC by 34.3% while maintaining the same level of performance.

engineering, electrical & electronic
A CMOS Time-of-Flight Image Sensor with High Dynamic Range Digital Pixel

Shanzhe Yu,Yacong Zhang,Fei Zhou,Wengao Lu,Shuyu Lei,Zhongjian Chen

DOI: https://doi.org/10.1109/asicon52560.2021.9620349

2021-01-01

Abstract:To widen measuring range and suppress background light, a CMOS time-of-flight image sensor with high dynamic range digital pixel is proposed. The sensing charge is quantized by extended-counting analogue-to-digital converter (ADC) which consists of pixel coarse quantization and column fine quantization. To maximize dynamic range in limited pixel area, the coarse quantization circuit is shared by 2×2 pixels, in which a novel up/down counter with a small number of transistors is proposed. Based on the pixel circuit, a 32×32 prototype TOF imager with 12μm-pitch digital pixel is designed in 0.11μm 1P4M CMOS image sensor technology. Simulation results show that a 104.6dB dynamic range of this ADC for wide measuring range is achieved at a frame rate of 50Hz.
A Low-Power i-ToF LiDAR With Nonlinearity Self-Calibration Technique

Youze Xin,Bing Zhang,Congzhen Hu,Yiyun Xie,Pengfei Hu,Ruipeng Yang,Yaoxin Li,Dan Li,Li Geng

DOI: https://doi.org/10.1109/tim.2023.3322502

IF: 5.6

2023-10-20

IEEE Transactions on Instrumentation and Measurement

Abstract:This article proposes a low-power indirect time-of-flight (i-ToF) vision system with a nonlinearity self-calibration technique. A pump gate modulator (PGM) technique is applied in the pixel to reduce the power consumption of pixel modulation. As a result, the pixel has a higher lateral electric field in a lower voltage swing of modulation, and the pixel can operate in the depletion state to achieve smaller load capacitance. To improve the nonlinearity of the sensor, nonlinearity self-calibration techniques are proposed. It includes the channel toggle technique and predistortion single-slope analog-to-digital converter (SS-ADC), which eliminates the quadratic nonlinearity in the readout channel and source follower (SF) nonlinearity in the pixel, respectively. Furthermore, it reduces the difficulty of nonlinear calibration of different batches of chips. The measured nonlinearity decreases greatly without back-end calibration, which is smaller than 0.8% within the distance range from 0.12 to 5 m. The receiver chip is fabricated in a 110-nm front-side illuminated (FSI) process with a pixel size. The chip power is only 130 mW.

engineering, electrical & electronic,instruments & instrumentation
A Low Power Multi-Mode Cmos Image Sensor with Integrated On-Chip Motion Detection

Xilin Liu,Milin Zhang,Jan Van der Spiegel

DOI: https://doi.org/10.1109/iscas.2013.6572366

2013-01-01

Circuits and Systems

Abstract:In this paper, we propose a novel low power multimode CMOS smart image sensor node with integrated focal-plane motion detection and video compression. An 80×80 image pixel array is fabricated in 0.5 μm 3M2P standard CMOS technology, occupying 3×3 mm2 silicon area. The proposed imager enables various operational modes, including 1) event generator mode, 2) motion tracking mode and 3) video output mode in full-resolution or compression by region of interest (ROI). An ultra low power focal-plane motion detection block, consisting of analog memory and dual-threshold comparator, is integrated in the pixel-level circuit for on-chip motion detection. A hardware-friendly motion tracking algorithm is developed that indicates ROIs according to a strategy based on the detection results. A 12-bit on-chip, off-array ADC is employed to convert the captured light intensity into digital readouts. In order to further reduce the power consumption, lower image resolution is used under the first two modes. A trade-off analysis between the image resolution and detection accuracy is proposed in this paper. In simulation, the total power consumption is 10μW at a frame rate of 30fps and a supply voltage of 3.3V in motion tracking mode. A compression ratio of 14% and an average PSNR of 42dB is achieved in compressive video output mode.
A 5.9μw Ultra-Low-Power Dual-Resolution CIS Chip of Sensing-with-Computing for Always-on Intelligent Visual Devices

Ziwei Li,Han Xu,Li Luo,Qi Wei,Fei Qiao

DOI: https://doi.org/10.1109/iscas51556.2021.9401338

2021-01-01

Abstract:In the intelligent IoT edge devices, power consumption is increasing due to the deployment of high-precision algorithms, which greatly limits the working time of the devices. The power of A/D conversion and data transmission has become the bottleneck of traditional visual system. In this paper, a new sensing-with-computing (Senputing) architecture is proposed to reduce this power bottleneck by combining imaging and BNN 1st-layer feature map computation. This Senputing architecture has two working modes, Normal-Sensor mode and Direct-Photocurrent-Computation mode with different resolutions (128×128 and 32×32). An ultra-low-power CMOS image sensor (CIS) chip with Senputing architecture is proposed to verify the feasibility. Our CIS chip is simulated with 180nm CMOS technology, the power of feature map computation is 5.9μW, and the frame rate is 208fps. The computation efficiency reaches to 8.23TOPs/W, which is 10.1 x higher than previous works.
Low Power Depth Estimation of Rigid Objects for Time-of-Flight Imaging

James Noraky,Vivienne Sze

DOI: https://doi.org/10.48550/arXiv.1810.01930

2019-03-26

Abstract:Depth sensing is useful in a variety of applications that range from augmented reality to robotics. Time-of-flight (TOF) cameras are appealing because they obtain dense depth measurements with minimal latency. However, for many battery-powered devices, the illumination source of a TOF camera is power hungry and can limit the battery life of the device. To address this issue, we present an algorithm that lowers the power for depth sensing by reducing the usage of the TOF camera and estimating depth maps using concurrently collected images. Our technique also adaptively controls the TOF camera and enables it when an accurate depth map cannot be estimated. To ensure that the overall system power for depth sensing is reduced, we design our algorithm to run on a low power embedded platform, where it outputs 640x480 depth maps at 30 frames per second. We evaluate our approach on several RGB-D datasets, where it produces depth maps with an overall mean relative error of 0.96% and reduces the usage of the TOF camera by 85%. When used with commercial TOF cameras, we estimate that our algorithm can lower the total power for depth sensing by up to 73%.

Image and Video Processing
Highly precise AMCW time-of-flight scanning sensor based on digital-parallel demodulation

Sung-Hyun Lee,Wook-Hyeon Kwon,Yoon-Seop Lim,Yong-Hwa Park

DOI: https://doi.org/10.48550/arXiv.2112.08556

IF: 4.729

2021-12-16

Signal Processing

Abstract:In this paper, a novel amplitude-modulated continuous wave (AMCW) time-of-flight (ToF) scanning sensor based on digital-parallel demodulation is proposed and demonstrated in the aspect of distance measurement precision. Since digital-parallel demodulation utilizes a high-amplitude demodulation signal with zero-offset, the proposed sensor platform can maintain extremely high demodulation contrast. Meanwhile, as all cross correlated samples are calculated in parallel and in extremely short integration time, the proposed sensor platform can utilize a 2D laser scanning structure with a single photo detector, maintaining a moderate frame rate. This optical structure can increase the received optical SNR and remove the crosstalk of image pixel array. Based on these measurement properties, the proposed AMCW ToF scanning sensor shows highly precise 3D depth measurement performance. In this study, this precise measurement performance is explained in detail. Additionally, the actual measurement performance of the proposed sensor platform is experimentally validated under various conditions.
A Priority-Based Selective Bit Dropping Strategy to Reduce DRAM and SRAM Power in Image Processing.

Xinghua Yang,Nanyang Huang,Yuanchang Chen,Fei Qiao,Huazhong Yang

DOI: https://doi.org/10.1587/elex.13.20160990

2016-01-01

IEICE Electronics Express

Abstract:By adopting the human visual system property, a priority-based selective bit dropping strategy to reduce DRAM (Dynamic Random Access Memory) and SRAM (Static Random Access Memory) power consumption is presented in this paper. The tradeoff between power consumption and output quality is explored as well. During the data flow in image processing, the original image data are first processed with our proposed strategy, from which the number of bit-'1' in lower part of each pixel is reduced. Then the approximate data are pushed into the DRAM and SRAM for further computation, where the refresh power consumption for DRAM is reduced due to the less bit-'1' in each data and the write power consumption for SRAM is also reduced due to the lower switch probability in write operation. The proposed strategy has been realized with digital logic circuits and the approximate image data are processed by the Discrete Cosine Transform (DCT) in simulation. The results show that 27.7% refresh power reduction on average for DRAM can be achieved and the SRAM also obtained 21.7% write power reduction with negligible overhead. As for the final output quality of the images, only 1.01 dB losses for Peak-Signal-Noise-Ratio (PSNR) is presented (about 3% lower than accurate processing) after the DCT processing.
Optical Readout Method Based on Time-Discrete Modulation for Micro-Cantilever Array Sensing

Xuhong Chu,Liquan Dong,Yuejin Zhao,Xiaomei Yu,Yun Feng

DOI: https://doi.org/10.3788/col201614.101102

IF: 2.56

2016-01-01

Chinese Optics Letters

Abstract:Noise and the resonance characteristics of the focal plane array ( FPA) are the most important factors that affect the performance of the optical readout infrared ( IR) FPA imaging system. This Letter presents a time-discrete modulation technology that eliminates the background and restrain noise, which effectively improves the image quality of the optical readout IR FPA imaging system. The comparative experiments show that this technology can reduce the noise equivalent temperature difference greatly and make the images sharper. Moreover, when the imaging system is influenced by the environment vibration, the images obtained from the imaging system with time-discrete modulation restore twice as fast as without time-discrete modulation.
Low-voltage 96 dB snapshot CMOS image sensor with 4.5 nW power dissipation per pixel

Arthur Spivak,Adam Teman,Alexander Belenky,Orly Yadid-Pecht,Alexander Fish

DOI: https://doi.org/10.3390/s120810067

Abstract:Modern "smart" CMOS sensors have penetrated into various applications, such as surveillance systems, bio-medical applications, digital cameras, cellular phones and many others. Reducing the power of these sensors continuously challenges designers. In this paper, a low power global shutter CMOS image sensor with Wide Dynamic Range (WDR) ability is presented. This sensor features several power reduction techniques, including a dual voltage supply, a selective power down, transistors with different threshold voltages, a non-rationed logic, and a low voltage static memory. A combination of all these approaches has enabled the design of the low voltage "smart" image sensor, which is capable of reaching a remarkable dynamic range, while consuming very low power. The proposed power-saving solutions have allowed the maintenance of the standard architecture of the sensor, reducing both the time and the cost of the design. In order to maintain the image quality, a relation between the sensor performance and power has been analyzed and a mathematical model, describing the sensor Signal to Noise Ratio (SNR) and Dynamic Range (DR) as a function of the power supplies, is proposed. The described sensor was implemented in a 0.18 um CMOS process and successfully tested in the laboratory. An SNR of 48 dB and DR of 96 dB were achieved with a power dissipation of 4.5 nW per pixel.
A Dual-Mode CMOS Image Sensor Based on In-Pixel Frame Differencing

Xu Ren,Liqiao Liu,Yandong He,Gang Du

DOI: https://doi.org/10.1109/iscas58744.2024.10558601

2024-01-01

Abstract:In this article, we introduce a dual-mode CMOS image sensor designed for pixel-level motion detection. A compact computational pixel structure is designed with a pitch of 8 mu m and a fill factor of 22.1%. We have implemented a current-mode motion detection module to generate motion signals and control the operation of the column-level analog-todigital converter (ADC) to optimize power efficiency. The data rate can be adjusted by tuning the threshold currents. A 128 x 128 image sensor is fabricated in a 0.18-mu m CMOS process. Test results indicate that the imager can output full image at 60 frames per second (fps). Of significant note are the substantial power consumption reductions achieved in both of the two motion detection modes, amounting to 30.7% and 60%, respectively. In data compression mode, a 3.02 pJ/pixel/frame Figure of Merit (FoM) is achieved.
A Low Power Up/Down Double-Data-Rate Counter For Cmos Image Sensors

Jingwei Wei,Sheng Xu,Dongmei Li

DOI: https://doi.org/10.1109/edssc.2019.8753979

2019-01-01

Abstract:A novel low power column level up/down double data-rate (DDR) counter for CMOS image sensors is proposed. To reduce the power consumption, a lowest bit circuit recording the parity information of the signal is designed. The proposed counter is suitable for the digital correlated double sampling operation. A 11-bit counter is realized with a 65nm CMOS process and the total power consumption in 500MHz clock is only 5.68 mu W which is 80.6% compared to a traditional up/down DDR counter.
An area‐effective and low‐power single‐slope ADC for DCG imaging CMOS image sensor

Rui Yang,Xiuyu Wang,Changju Liu,Biao Ma,Kaiming Nie,Jiangtao Xu

DOI: https://doi.org/10.1002/cta.4109

IF: 2.378

2024-05-28

International Journal of Circuit Theory and Applications

Abstract:This paper introduces a readout circuit structure tailored for high dynamic range CISs utilizing DCG imaging technology, using only one ADC for A/D conversion of HCG signals and LCG signals, which greatly reduces the area and power consumption of the readout circuit. Summary This paper introduces an area‐effective and low‐power readout circuit structure tailored for high dynamic range (HDR) CMOS image sensors (CISs) utilizing dual conversion gain (DCG) imaging technology. A switched capacitor amplifier, which is applied at the comparator input port of the column‐parallel single‐slope analog‐to‐digital converter (SS ADC), is proposed to compensate for the charge injection and clock feed‐through introduced when the pixel switches between high conversion gain (HCG) and low conversion gain (LCG) modes. The proposed SS ADC is supplemented by the integration of a configurable counter, and the counter is specifically crafted for performing the A/D conversion of the readout voltage within a DCG pixel. Compared to the conventional DCG readout circuit, the proposed readout circuit use only one ADC for A/D conversion of HCG signals and LCG signals, which greatly reduces the area and power consumption of the readout circuit. Simulation results under 110 nm CMOS technology illustrate that the proposed 10‐bit SS ADC has a DNL of +0.78/−0.91 LSB and an INL of +1.91/−1.69 LSB, with a SNR of 57.2 dB and a SNDR of 55.95 dB, corresponding to an ENOB of 9 bits. The power consumption of the proposed SS ADC is 56.4 μW per column with a conversion time of 12 μs, and the simulation results show that the power consumption is 23.35% lower than the conventional structure and the area is saved by 24.69%.

engineering, electrical & electronic

[Problems in hemolytic anemias with pyruvate kinase deficiency. I. Clinical and hematologic picture in 4 patients].

A Reconfigurable Convolution-in-Pixel CMOS Image Sensor Architecture

A Two-Tap Indirect Time-of-Flight CMOS Image Sensor With Pump Gate Modulator for Low-Power Applications

A 0.18 Μm High Resolution Bandpass Delta-Sigma Modulator for Acceleration Transducer Applications

Transverse Dynamic Modulation Transfer Function of Subpixel Push-Scanning Imaging by Linear CCD

A Time-to-Digital Converter for Low-Power Consumption Single Slope Analog-to-Digital Converters in a High-Speed CMOS Image Sensor

Identification of a Novel Abscisic Acid-Regulated Farnesol Dehydrogenase from Arabidopsis1[W][OA]

6.9 A 0.35V 0.367TOPS/W Image Sensor with 3-Layer Optical-Electronic Hybrid Convolutional Neural Network

A low power 10‐bit 1 MS/s cyclic analog to digital converter for complementary metal oxide semiconductors image sensors with comparator‐based switched‐capacitor technique

A CMOS Time-of-Flight Image Sensor with High Dynamic Range Digital Pixel

A Low-Power i-ToF LiDAR With Nonlinearity Self-Calibration Technique

A Low Power Multi-Mode Cmos Image Sensor with Integrated On-Chip Motion Detection

A 5.9μw Ultra-Low-Power Dual-Resolution CIS Chip of Sensing-with-Computing for Always-on Intelligent Visual Devices

Low Power Depth Estimation of Rigid Objects for Time-of-Flight Imaging

Highly precise AMCW time-of-flight scanning sensor based on digital-parallel demodulation

A Priority-Based Selective Bit Dropping Strategy to Reduce DRAM and SRAM Power in Image Processing.

Optical Readout Method Based on Time-Discrete Modulation for Micro-Cantilever Array Sensing

Low-voltage 96 dB snapshot CMOS image sensor with 4.5 nW power dissipation per pixel

A Dual-Mode CMOS Image Sensor Based on In-Pixel Frame Differencing

A Low Power Up/Down Double-Data-Rate Counter For Cmos Image Sensors

An area‐effective and low‐power single‐slope ADC for DCG imaging CMOS image sensor