Abstract:Solid electrolytes (SEs) are vital for all-solid-state batteries (ASSBs) since they replace the flammable liquid electrolytes to make the ASSBs safer and compacter. 1 In order to boost the energy density of ASSBs, a practical SE is not only expected possessing high ionic conductivity, but also good compatibility with both cathode and anode to allow the use of high-voltage cathode and Li metal. 2, 3 However, most of the developed SEs show limitations on directly contact with either high-voltage cathode materials or Li metal. As such, SE modification is required to address the interfacial issues between SE and electrodes. In this work, fluorinated sulfide- and halide-based SEs are proposed to stabilize the SE/Li metal and SE/high-voltage cathode interfaces, respectively. Our results firstly show that fluorinated argyrodite Li 6 PS 5 Cl (LPSCl) can enhance the interfacial stability toward the Li metal anode. 4 The in-situ formed interface between Li and LPSCl 1−x F x are of highly fluorinated and condense, which enables ultrastable Li plating/stripping behavior over 250 hrs at a high current density of 6.37 mA cm −2 and a cutoff capacity of 5 mAh cm −2 . The Li metal treated by the LPSCl 1−x F x SE is then demonstrated to deliver good durability and rate capability in full cells. Other than anode side improvement, F is introduced into a superionic conductor Li 3 InCl 6 to widen the oxidation limit to over 6 V (vs. Li/Li + ). 5 Both experimental and computational results identify that F-containing passivating interphases are generated to contribute to the enhanced oxidation stability of Li 3 InCl 6-x F x and stabilization the surface of cathodes at high cut-off voltages. The optimized composition Li 3 InCl 4.8 F 1.2 is directly matched with bare high-voltage LiCoO 2 , enabling ASSBs to stably operate at room temperature at a cut-off voltage of 4.8 V (vs Li/Li + ). Our studies provide a new strategy of interface engineering by introducing F in SEs, realizing the good compatibility between SE and electrodes and opening up the applications of ASSBs. Re ferences Manthiram, A., Yu, X. W., Wang, S. F. Lithium battery chemistries enabled by solid-state electrolytes. Nat. Rev . Mater. 2, 1-16 (2017). Wang, C. H., Liang, J. W., Zhao, Y., Zheng, M. T., Li, X. N., Sun, X. L. All-solid-state lithium batteries enabled by sulfide electrolytes: from fundamental research to practical engineering design. Energy Environ. Sci. 14, 2577-2619 (2021). Li, J. C., Ma, C., Chi, M. F., Liang, C. D., Dudney, N. J. Solid Electrolyte: the Key for High-Voltage Lithium Batteries. Adv. Energy Mater. 5, 1401408 (2015). Zhao, F. P., et al. Ultrastable Anode Interface Achieved by Fluorinating Electrolytes for All-Solid-State Li Metal Batteries. ACS Energy Lett. 5, 1035-1043 (2020). Zhang, S. M., et al. Advanced High-Voltage All-Solid-State Li-Ion Batteries Enabled by a Dual-Halogen Solid Electrolyte. Adv. Energy Mater. 11, 2100836 (2021).

Water‐Stable Sulfide Solid Electrolyte Membranes Directly Applicable in All‐Solid‐State Batteries Enabled by Superhydrophobic Li + ‐Conducting Protection Layer

Highly Conductive Sulfide Solid-State Electrolytes for All-Solid-State Li Battery

Ultrathin Superhydrophobic Coatings for Air‐Stable Inorganic Solid Electrolytes: Toward Dry Room Application for All‐Solid‐State Batteries

Superior All‐Solid‐State Batteries Enabled by a Gas‐Phase‐Synthesized Sulfide Electrolyte with Ultrahigh Moisture Stability and Ionic Conductivity

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

Interface Engineering Via Fluorinated Solid Electrolytes for All-Solid-State Li Batteries

Enhancing Moisture Stability of Sulfide Solid-State Electrolytes by Reversible Amphipathic Molecular Coating

In situ formed interfacial layer for all-solid-state lithium batteries with sulfide electrolyte films

Boosting the Interfacial Stability of the Li6PS5Cl Electrolyte with a Li Anode via In Situ Formation of a LiF-Rich SEI Layer and a Ductile Sulfide Composite Solid Electrolyte

The Contact Interface Engineering of All-Sulfide-Based Solid State Batteries Via Infiltrating Dissoluble Sulfide Electrolyte

Solid-State Plastic Crystal Electrolytes: Effective Protection Interlayers For Sulfide-Based All-Solid-State Lithium Metal Batteries

High Ionic Conductive, Mechanical Robust Sulfide Solid Electrolyte Films and Interface Design for All‐Solid‐State Lithium Metal Batteries

Surface molecular engineering to enable processing of sulfide solid electrolytes in humid ambient air

Surface Coating Enabling Sulfide Solid Electrolytes with Excellent Air Stability and Lithium Compatibility

Enabling high-performance all-solid-state lithium batteries with high ionic conductive sulfide-based composite solid electrolyte and ex-situ artificial SEI film

Sulfide-based Solid Electrolyte and Electrode Membranes for All-Solid-state Lithium Batteries

A Dual-Halogen Electrolyte for Protective-Layer-free All-Solid-state Lithium Batteries

Sulfide Solid Electrolyte Thin Film with High Ionic Conductive from Slurry-Casting Strategy for All-Solid-state Lithium Batteries

Thin and Flexible Solid Electrolyte Membranes with Ultrahigh Thermal Stability Derived from Solution-Processable Li Argyrodites for All-Solid-State Li-Ion Batteries

High-Performance Li-SeS x All-Solid-State Lithium Batteries.