Abstract:This study aims to characterize airborne particles emitted from a metal additive manufacturing machine and related levels of occupational exposure. To achieve this, a complete measurement methodology was deployed around a direct energy deposition machine. Different operating conditions were investigated, based on configurations of two materials and two injection nozzles. Two replicates were performed for each condition. Airborne particles emitted during repeated manufacturing cycles were measured simultaneously at the source, in the near field, in the far field and on the operator. Real-time instruments were used to characterize the machine emissions (10 nm–10 µm) associated with respirable and inhalable samplers and cascade impactors. Measurements were made during both the manufacturing process and transient operating phases. In parallel, personal exposure to hexavalent chromium was assessed. The number of particles measured for the different machining phases show that high levels of particles (> 5 × 105 # cm−3, 0.3–1.3 mg m−3 inhalable particles, 0.2–6 µg m−3 CrVI) were emitted in the machine enclosure. The size distributions indicate that more than 90% of the particles are smaller than 250 nm. Occupational exposure to CrVI was found to be below the LOQ of 0.098 µg m−3 for the two alloys investigated. During the machining process, near-field number and mass concentrations were ∼ 104 # cm−3, and below 0.04 mg m−3, respectively. Far-field number concentrations were also on the order of 104 # cm−3 throughout the whole monitoring period. The transient phase of door opening was found to result in high levels of exposure (> 105 # cm−3), which were also detected in the near-field, confirming the need to implement preventative actions. To address this issue, a collective protective measure, consisting of setting a time delay of about 8 min between the end of the manufacturing process and opening of the door, could be employed. This collective measure should also be accompanied by the wearing of personal protective equipment by the operator when an intervention in the machine enclosure is necessary.

Collection and characterization of aerosols from metal cutting techniques typically used in decommissioning nuclear facilities

Aerodynamic diameter and radioactivity distributions of radioactive aerosols from activated metals cutting for nuclear power plant decommissioning

Characteristics of radioactive aerosols during the pre-decommission phase of the experimental shielding reactor

Aerosol, Gas, and Swarf Production during Underwater Cutting of Reactor Core Internals Using Electron Discharge Machining

Performance assessment of HEPA filter against radioactive aerosols from metal cutting during nuclear decommissioning

Sampling for Characterizing Radioactive Aerosol From Activated Metal During Cutting With Plasma Arc Torch for Internal Dose Assessment

Investigation of aerosol generation through laser cleaning of various surfaces and optimization of mist & spray scavenging

Application of Plasma Arc Cutting Technology in Dismantling of Large Metal Components in Containment Building

Laser cutting study of zirconium alloys for nuclear decommissioning

Numerical investigation on improved spray system for efficient aerosol removal during the decommissioning of Fukushima Daiichi nuclear power plants

Development of a Multi-technique Characterization Portfolio for Stainless Steels Exposed to Magnox Reprocessing Liquors

Research on aerosol particles formed by laser interaction with various metals

Size-separated particle fractions of stainless steel welding fume particles - A multi-analytical characterization focusing on surface oxide speciation and release of hexavalent chromium

62 Evaluating the Potential Exposure to Metal Fine and Nano Particles Generated During Wire and Powder Laser Metal Deposition

Characterizing particle emissions from a direct energy deposition additive manufacturing process and associated occupational exposure to airborne particles

Evaluation of the Potential Airborne Release of Carbon Nanofibers During the Preparation, Grinding, and Cutting of Epoxy-Based Nanocomposite Material

29 Fugitive Emissions from Carbon Dioxide Laser Cutting Activities

Evaluation of Potential Occupational Exposure and Release of Nanoparticles in Semiconductor-Manufacturing Environments

Determination of Airborne Release Fractions from Loose Powder Contamination Under Impact Stress

Numerical Simulation and Experiments Study on Laser Ablation Decontamination for Strontium and Cesium from Contaminated 316L Stainless Steels in Spent Nuclear Fuel Reprocessing

Source Apportionment of Particulate Matter in a Metal Workshop