Abstract:Pulsed thermography is a commonly used non-destructive testing method and is increasingly studied for the assessment of advanced materials such as carbon fibre-reinforced polymer (CFRP). Different processing approaches are proposed to detect and characterize anomalies that may be generated in structures during the manufacturing cycle or service period. In this study, matrix decomposition using Robust PCA via Inexact-ALM is investigated as a pre- and post-processing approach in combination with state-of-the-art approaches (i.e., PCT, PPT and PLST) on pulsed thermography thermal data. An academic sample with several artificial defects of different types, i.e., flat-bottom-holes (FBH), pull-outs (PO) and Teflon inserts (TEF), was employed to assess and compare defect detection and segmentation capabilities of different processing approaches. For this purpose, the contrast-to-noise ratio (CNR) and similarity coefficient were used as quantitative metrics. The results show a clear improvement in CNR when Robust PCA is applied as a pre-processing technique, CNR values for FBH, PO and TEF improve up to 164%, 237% and 80%, respectively, when compared to principal component thermography (PCT), whilst the CNR improvement with respect to pulsed phase thermography (PPT) was 77%, 101% and 289%, respectively. In the case of partial least squares thermography, Robust PCA results improved not only only when used as a pre-processing technique but also when used as a post-processing technique; however, this improvement is higher for FBHs and POs after pre-processing. Pre-processing increases CNR scores for FBHs and POs with a ratio from 0.43% to 115.88% and from 13.48% to 216.63%, respectively. Similarly, post-processing enhances the FBHs and POs results with a ratio between 9.62% and 296.9% and 16.98% to 92.6%, respectively. A low-rank matrix computed from Robust PCA as a pre-processing technique on raw data before using PCT and PPT can enhance the results of 67% of the defects. Using low-rank matrix decomposition from Robust PCA as a pre- and post-processing technique outperforms PLST results of 69% and 67% of the defects. These results clearly indicate that pre-processing pulsed thermography data by Robust PCA can elevate the defect detectability of advanced processing techniques, such as PCT, PPT and PLST, while post-processing using the same methods, in some cases, can deteriorate the results.

Pulsed Thermography Inspection of Composite Anticorrosive Coatings: Defect Detection and Analysis of Their Thermal Behavior through Computational Simulation

Carbon fiber composites inspection and defect characterization using active infrared thermography: numerical simulations and experimental results

Statistical and Machine Learning-Based Imaging with Long Pulse Thermography for the Detection of Non-standardised Defects in CFRP Composites

Characterizing Influence Parameters in Pulsed Phase Thermography for Defect Detection in Sheet Metal Parts

Inspection of defects in composite structures using long pulse thermography and shearography

Pulsed Infrared Thermography to Inspect the Internal Defects of Composite Insulators

Robust Principal Component Thermography for Defect Detection in Composites

Defect Detection and Depth Estimation in Composite Materials for Pulsed Thermography Images by Nonuniform Heating Correction and Oriented Gradient Information

Thermal Nondestructive Testing of Composite and Metal Parts Manufactured by Additive Technologies

Detection of corrosion under insulation on aerospace structures via pulsed eddy current thermography

Numerical Modelling of the Heat Source and the Thermal Response of an Additively Manufactured Composite during an Active Thermographic Inspection

Improved Non-Destructive Testing of Carbon Fiber Reinforced Polymer (CFRP) Composites Using Pulsed Thermograph

Eddy Current Pulsed Thermography for Steel Corrosion Characterization

Applications of Thermography and Ultrasonics for Detection of Debonding in Carbon Fibre Reinforced Composite Panels

Distance Effect in Transient Thermography for Internal Defects Detection in Composites

Automated Impact Damage Detection Technique for Composites Based on Thermographic Image Processing and Machine Learning Classification

Fusion of Polarization Degree and Thermal Parameters for Enhanced Nondestructive Testing of Coated Metals

INFRARED THERMOGRAPHY TECHNIQUE FOR DAMAGE DETECTION ON COMPOSITE MATERIALS UNDER LOW-ENERGY IMPACT

Accurate Depth Determination of Defects in Composite Materials Using Pulsed Thermography

A Comparison among Different Ways to Investigate Composite Materials with Lock-In Thermography: The Multi-Frequency Approach

Data Enhancement via Low-Rank Matrix Reconstruction in Pulsed Thermography for Carbon-Fibre-Reinforced Polymers