Abstract:Carbon nanotube field-effect transistors (CNT FETs) have been demonstrated to exhibit high performance only through low-temperature fabrication process and require a low thermal budget to construct monolithic three-dimensional (M3D) integrated circuits (ICs), which have been considered a promising technology to meet the demands of high-bandwidth computing and fully functional integration. However, the lack of high-quality CNT materials at the upper layer and a low-parasitic interlayer dielectric (ILD) makes the reported M3D CNT FETs and ICs unable to provide the predicted high performance. In this work, we demonstrate a multilayer stackable process for M3D integration of high-performance aligned carbon nanotube (A-CNT) transistors and ICs. A low-kappa (similar to 3) interlayer SiO2 layer is prepared from spin-on-glass (SOG) through processes with a highest temperature of 220 C-degrees, presenting low parasitic capacitance between two transistor layers and excellent planarization to offer an ideal surface for the A-CNT and device fabrication process. A high-quality A-CNT film with a carrier mobility of 650 cm(2) V-1 s(-1) is prepared on the ILD layer through a clean transfer process, enabling the upper CNT FETs fabricated with a low-temperature process to exhibit high on-state current (1 mA mu m(-1)) and peak transconductance (0.98 mS mu m(-1)). The bottom A-CNT FETs maintain pristine high performance after undergoing the ILD growth and upper FET fabrication. As a result, 5-stage ring oscillators utilizing the M3D architecture show a gate propagation delay of 17 ps and an active region of approximately 100 mu m(2), representing the fastest and the most compact M3D ICs to date.

Laminated three-dimensional carbon nanotube integrated circuits

Monolithic Three‐dimensional Integration of Aligned Carbon Nanotube Transistors for High‐performance Integrated Circuits

Fabrication of Three-dimensional Thermally Conductive Carbon Fibers/Carbon Nanotubes Network Reinforce Epoxy Composites

Towards 3-D Carbon-Based Heterogeneous Interconnects

Electrical Modeling of Three-Dimensional Carbon-Based Heterogeneous Interconnects

Speeding up carbon nanotube integrated circuits through three-dimensional architecture

Carbon Nanotube with Chemically Bonded Graphene Leaves for Electronic and Optoelectronic Applications

Cellulose‐Nanofiber‐Enabled 3D Printing of a Carbon‐Nanotube Microfiber Network

Three-Dimensional Flexible Complementary Metal-Oxide-Semiconductor Logic Circuits Based on Two-Layer Stacks of Single-Walled Carbon Nanotube Networks.

3D Assembly of Carbon Nanotubes for Fabrication of Field-Effect Transistors Through Nanomanipulation and Electron-Beam-Induced Deposition

Monolithic Three-Dimensional Integration of Carbon Nanotube Circuits and Sensors for Smart Sensing Chips

Single Carbon Fibers with a Macroscopic-Thickness, 3D Highly Porous Carbon Nanotube Coating

Carbon Nanotube Field‐Effect Transistors: Towards Entire‐Carbon‐Nanotube Circuits: the Fabrication of Single‐Walled‐Carbon‐Nanotube Field‐Effect Transistors with Local Multiwalled‐Carbon‐Nanotube Interconnects (adv. Mater. 13/2009)

Fabrication and Electrical Characterization of Densified Carbon Nanotube Micropillars for IC Interconnection

Carbon Nanotube Integrated Circuit Technology: Purification, Assembly and Integration

Multilevel, Multicomponent Microarchitectures of Vertically-Aligned Carbon Nanotubes for Diverse Applications

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration

Three-dimensional metal-graphene-nanotube multifunctional hybrid materials.

Carbon Nanotube Electronics: Recent Advances

Carbon nanotube-based flexible electronics

Towards Future VLSI Interconnects Using Aligned Carbon Nanotubes