Abstract:The SiC/Si composites were prepared via selective laser sintering (SLS) combined with reactive melt infiltration (RMI) of liquid Si, using fine SiC particles with original particle sizes of 0.05, 0.8 and 5 μm. A novel electrostatic spraying combined with phase inversion (ES-PI) method was developed to assemble SiC particles into spherical powders (40–60 μm in diameter) before SLS, enabling SiC with excellent flowability. Commercial coarse SiC microparticles (∼40 μm) were also adopted to prepare the SiC/Si reference composite for comparison. Then the effects of the fine original particle sizes of SiC on the microstructures, as well as mechanical performance of composites were studied. Compared to commercial SiC microparticles, the ES-PI SiC microspheres show superior sphericity and fluidity but a relatively high porosity. However, the pores in ES-PI SiC microspheres, which are potentially detrimental to mechanical properties of composites, will be totally filled and eliminated in the SiC/Si composites after RMI. The mechanical performance of the SiC/Si composites printed using the fine nano (0.05 μm) and submicron (0.8 μm) original particles was effectively improved than the reference composite. When printed using the ES-PI SiC microspheres with 0.05 μm original particles, the flexural strength of the SiC/Si composite was enhanced by 25 %. This is attributed to the cracks deflection as well as the fracture mode transition from transgranular to intergranular rupture by the use of nano- or submicro-sized original SiC particles. This work provides an effective solution for preparing high strength SiC/Si composites with fine nano- or submirco particle sizes for space-based lightweight optical mirror using SLS.

Effects of particle grading on properties of silica ceramics prepared by selective laser sintering

Improved mechanical properties of silica ceramic cores prepared by 3D printing and sintering processes

Improved precision and mechanical properties of 3D‐printed silica ceramics via sintering temperature optimization

Enhancing mechanical properties of selectively laser sintered SiC/Si composites printed using electrostatic spraying microspheres with fine particles

Particle size gradation design and performance enhancement of quartz cores for precision casting

Selective laser sintering of porous Al2O3-based ceramics using both Al2O3 and SiO2 poly-hollow microspheres as raw materials

Effects of raw material ratio and post-treatment on properties of soda lime glass-ceramics fabricated by selective laser sintering

Performance Optimization of Complicated Structural SiC/Si Composite Ceramics Prepared by Selective Laser Sintering

Effect of gradation on thermal and mechanical properties of reaction‐bonded silicon carbide ceramics

The Effect of Particle Distribution to the Sintering Properties of Al2o3 Ceramic Formed by Stereolithography

Fabrication of high-performance silica-based ceramic cores through selective laser sintering combined with vacuum infiltration

Effects Of Grain Grading On Microstructures And Mechanical Behaviors Of Pressureless Solid-State-Sintered Sic

Infiltration of silica slurry into silica-based ceramic cores prepared by selective laser sintering based on pre-sintering

Effects of carbon content on microstructure and mechanical properties of SiC ceramics fabricated by SLS/RMI composite process

Effects of AlN inorganic binder on the properties of porous Si3N4 ceramics prepared by selective laser sintering

A Reverse Particle Grading Strategy for Design and Fabrication of Porous SiC Ceramic Supports with Improved Strength

Improved mechanical properties of SiB6 reinforced silica-based ceramic cores fabricated by 3D stereolithography printing

Porous SiC Ceramics with Controllable Porosity Achieved by Micro-sized Powder through Recrystallization Sintering

The Effect of Particle Size Distribution on the Microstructure and Properties of Al2O3 Ceramics Formed by Stereolithography

Preparation of high-performance silica-based ceramic cores with B4C addition using selective laser sintering and SiO2–Al2O3 sol infiltration

Microstructure and properties evolution of silicon-based ceramic cores fabricated by 3D printing with stair-stepping effect control