Abstract:The urgent need for carbon dioxide (CO 2 ) capture technologies motivates this chemical engineering study, which systematically investigates the influence of macroscopic and microscopic structure on the CO 2 absorption performance of hydrophobic alumina (Al 2 O 3 ) hollow fiber membrane (A-HFMs) contactors. Six different A-HFMs prepared using the non-solvent-induced phase separation (NIPS) method with select solvents followed by sintering at 1300°C were then tested for chemical CO 2 absorption in an A-HFM contactor using a monoethanolamine (MEA) solution. The hydrophobicity of the coatings applied on the A-HFM surfaces was confirmed by the water contact angle and thermogravimetric (TGA) analysis. Pearson's statistical analysis of a correlation matrix revealed the strength of relationships between nine variables, including outer diameter (mm), inner diameter (mm), percentage of sponge layer (%), pore size (nm), maximum pore size (nm), mechanical strength (MPa), surface porosity (m −1 ), overall porosity (%), and CO 2 absorption flux (mol m −2 s −1 ). Building upon these findings, this study unveils a novel non-linear function linking three specific microscopic characteristics— pore size, surface porosity, and a geometric sponge layer factor—to CO 2 absorption flux, offering valuable insights for optimizing hydrophobic A-HFM design and enhancing CO 2 capture efficiency. The A-HFM, characterized by the combination of three factors (higher pore size, increased surface porosity, and a thicker sponge layer), achieved a CO 2 absorption flux of 6.36 ×10 −3 mol m −2 s −1 at room temperature, showcasing its exceptional performance in capturing CO 2 . The resulting empirical morphological factor provides a novel approach for enhancing the performance of CO 2 absorption through A-HFM design optimization.

CO2 capture based on Al2O3 ceramic membrane with hydrophobic modification

CO2 capture using superhydrophobic ceramic membrane: Preparation and performance analysis

Preparation and Modification of Ceramic Membrane and Its Application in Oil/Water Wastewater Treatment

Study on Co2 Removal in Air by Hydrogel Membranes

Superhydrophobic Ceramic Membrane Coupled with a Biphasic Solvent for Efficient CO2 Capture

Fabrication and Characterization of Superhydrophobic Polypropylene Hollow Fiber Membranes for Carbon Dioxide Absorption

CO2 Capture using a Superhydrophobic Ceramic Membrane Contactor

Study on design strategies and on new structure-performance relationships for CO 2 capture in gas-liquid hollow fiber membrane contactors

Fabrication of Cost-Effective and Antifouling Al2O3-SiO2 Membrane for Efficient Oil Emulsion Separation

Fabrication and Performance Evaluation of Industrial Alumina Based Graded Ceramic Substrate for CO2 Selective Amino Silicate Membrane

In Situ-Grown Al2O3 Nanoflowers and Hydrophobic Modification Enable Superhydrophobic SiC Ceramic Membranes for Membrane Distillation

Ceramic membrane with double catalytic layer for efficient peroxymonosulfate activation and dissolved organic matter (DOM) membrane fouling control

Hydrophobic interface-assisted casting of Al-supported, CaO-based sorbent pellets for high-temperature CO 2 capture

Hierarchical porous AlOOH hollow microspheres for efficient CO2 capture

ScienceDirect The 7 th International Conference on Applied Energy – ICAE 2015 CO 2 capture using a superhydrophobic ceramic membrane contactor

Chemical-grafting of graphene oxide quantum dots (GOQDs) onto ceramic microfiltration membranes for enhanced water permeability and anti-organic fouling potential

Ceramic Membrane with Protein-Resistant Surface Via Dopamine/diglycolamine Co-Deposition

Superhydrophobic Alumina Hollow Ceramic Membrane Modi Fi Ed by TiO2 Nanorod Array for Vacuum Membrane Distillation

Ceramic Membranes with Mussel-Inspired and Nanostructured Coatings for Water-in-oil Emulsions Separation

Hydrophilic modification of Al2O3 microfiltration membrane with nano-sized γ-Al2O3 coating

Optimization of preparation process and characterization for hydrophobic α-Al2O3 ceramic membrane