Phosphorus-doped lithium- and manganese-rich layered oxide cathode material for fast charging lithium-ion batteries

Yuqiong Kang,Xingang Guo,Zhiwu Guo,Jiangang Li,Yunan Zhou,Zheng Liang,Cuiping Han,Xiangming He,Yun Zhao,Naser Tavajohi,Baohua Li

DOI: https://doi.org/10.1016/j.jechem.2021.04.026

IF: 13.1

2021-11-01

Journal of Energy Chemistry

Abstract:Owing to their high theoretical specific capacity and low cost, lithium- and manganese-rich layered oxide (LMR) cathode materials are receiving increasing attention for application in lithium-ion batteries. However, poor lithium ion and electron transport kinetics plus side effects of anion and cation redox reactions hamper power performance and stability of the LMRs. In this study, LMR Li1.2Mn0.6Ni0.2O2 was modified by phosphorus (P)-doping to increase Li+ conductivity in the bulk material. This was achieved by increasing the interlayer spacing of the lithium layer, electron transport and structural stability, resulting in improvement of the rate and safety performance. P5+ doping increased the distance between the (003) crystal planes from ~0.474 nm to 0.488 nm and enhanced the structural stability by forming strong covalent bonds with oxygen atoms, resulting in an improved rate performance (capacity retention from 38% to 50% at 0.05 C to 5 C) and thermal stability (50% heat release compared with pristine material). First-principles calculations showed the P-doping makes the transfer of excited electrons from the valence band to conduction band easier and P can form a strong covalent bond helping to stabilize material structure. Furthermore, the solid-state electrolyte modified P5+ doped LMR showed an improved cycle performance for up to 200 cycles with capacity retention of 90.5% and enhanced initial coulombic efficiency from 68.5% (pristine) or 81.7% (P-doped LMR) to 88.7%.

chemistry, physical,engineering, chemical, applied,energy & fuels

What problem does this paper attempt to address?

The problem that this paper attempts to solve is the poor kinetic performance and insufficient structural stability of lithium - rich manganese - based layered oxide (LMR) cathode materials in lithium - ion batteries during high - rate charging and discharging. Specifically, the article points out that although LMR materials have a relatively high theoretical specific capacity and a relatively low cost, their poor lithium - ion and electron transport kinetics as well as the side effects of anion and cation redox reactions limit their power performance and stability. In addition, the article also mentions that LMR materials have problems of poor intrinsic electronic conductivity and structural stability, which hinder their commercial applications.

To improve these problems, the authors propose a method to modify Li₁.₂Mn₀.₆Ni₀.₂O₂ through phosphorus - doping (P - doping). Phosphorus - doping can increase the inter - layer spacing of the material, improve the electron - transport performance and enhance the structural stability, thereby significantly improving the rate performance and safety of the material. The experimental results show that P⁵⁺ - doping increases the (003) crystal - plane spacing from approximately 0.474 nm to 0.488 nm, and by forming strong covalent bonds with oxygen atoms, enhances the structural stability of the material. These improvements have significantly increased the capacity retention rate of the material at different rates (from 38% to 50%), and the thermal stability has also been improved (heat release is reduced by 50%). In addition, based on first - principles calculations, P - doping makes it easier for excited electrons to transfer from the valence band to the conduction band, and P can form strong covalent bonds to help stabilize the material structure. Further research shows that the solid - state - electrolyte - modified P⁵⁺ - doped LMR material can still maintain a capacity retention rate of 90.5% after 200 cycles, and the initial Coulomb efficiency is increased from 68.5% (undoped) or 81.7% (P - doped LMR) to 88.7%.

In summary, this research aims to improve the kinetic performance and structural stability of lithium - rich manganese - based layered oxide cathode materials through phosphorus - doping technology to meet the application requirements of fast - charging lithium - ion batteries.