Sequence Note: Genetic Characterization of the V3 Loop Sequences of 21 HIV Type 1 Spanish Isolates from Hemophilia Patients

M. Ortíz,A. Bernal,V. Jiménez,M. Magallón,A. García‐Sáiz

DOI: https://doi.org/10.1089/AID.1998.14.1487

1998-11-01

Abstract:

What problem does this paper attempt to address?

Measuring the Refractive Index of Optical Adhesives at Cryogenic Temperatures.

Xintong Hou,Ni Yao,Lixing You,Hao Li,Wei Fang,Weijun Zhang,Zhen Wang,Limin Tong,Xiaoming Xie

DOI: https://doi.org/10.1364/ao.386265

IF: 1.9

2020-01-01

Applied Optics

Abstract:The development of photonic quantum information technologies requires research on the properties of optical adhesives at cryogenic temperatures. In the process of developing microfiber (MF)-coupled superconducting nanowire single-photon detectors (SNSPDs), we invented a cryogenic-temperature refractive index (RI) measurement method based on a kind of MF device. The device was put into the cryostat to observe the variance of MF transmittance with temperature. Then an RI–temperature relationship was established through the correspondence between the confinement conditions of MFs of various diameters in an optical adhesive– M g F 2 environment and transmittance–temperature curves. Using this method, we analyzed the thermal-optical properties of a commercial fluorinated acrylic optical adhesive and obtained the RI values of the adhesive at various temperatures. The results were successfully applied in the development of broadband and high-efficiency MF-coupled SNSPDs.
Measurement of Polarization Mode Couplings in Polarization-Maintaining Fibers Based on White Light Interference

HF Li,G Zhou,WC Jing,XM Man,YM Zhang

DOI: https://doi.org/10.1117/12.482026

2002-01-01

Abstract:In this paper, a novel method to measure the distributed polarization mode coupling in polarization-maintaining (PM) fibers is introduced. The measurement system is based on white light interference. A super luminescent diode is used as the broadband light source in the system. The whole test system is working on 1300nm wavelength. There are two main parts of the measurement equipment: polarization adjustment and a scanned Michelson interferometer. In order to improve the accuracy, a piezoelectric transducer (PZT) is-applied in the scanned Michelson interferometer. The maximum length of tested polarization-maintaining fiber is one kilometer, and the spatial resolution of this method reached 60 mm along the tested PM fiber. The degree of polarization mode coupling that could be detected is -75dB.
Verification of calibration methods for determining photon-counting detection efficiency using superconducting nano-wire single photon detectors

I Mueller,R D Horansky,J H Lehman,S W Nam,I Vayshenker,L Werner,G Wuebbeler,M White

DOI: https://doi.org/10.1364/OE.25.021483

2017-09-04

Abstract:In recent years several ways to radiometrically calibrate optical fiber-coupled detectors have been developed. However, fiber-coupled calibration methods for single photon detectors have not been compared by national metrology institutes in order to validate their equivalence or traceability to the international systems of units yet.. Here, we present the comparison of radiometric calibration methods traceable to a NIST cryogenic radiometer at the 'few-photon' level. The calibration methods are based on metrology grade optical power meters. The expanded (k = 2) relative standard uncertainties of the calibration methods for the detection efficiency are of the order of 0.5%. However, the results changed relatively by 10% with a different set of optical fibers and mating connectors. These results stress the importance of fiber-core dimensions and fiber-connector repeatability.
Traceable characterisation of fibre-coupled single-photon detectors

Luke Arabskyj,Philip Dolan,Adam Parke,Ted Santana,Simon Hall,Geiland Porrovecchio,Marek Smid,Marco Lucamarini,Christopher Chunnilall

DOI: https://doi.org/10.1088/1681-7575/ad70bc

2024-08-21

Metrologia

Abstract:The detection of single photons plays an essential role in advancing single-photon science and technologies. Yet, within the visible/near-infrared (vis/NIR) spectral region, accurate fibre-based optical power measurements at the few-photon level are not yet well-established. In this study, we report on a fibre-based setup, enabling traceable optical power measurements at the few-photon level in this spectral region. The setup was used to calibrate the detection efficiency (DE) of four single-photon avalanche diode (SPAD) detectors. The absolute standard uncertainties on the mean DE values ranged from 0.20% to 0.27% (k = 2). However, the standard deviation of DE values over repeat fibre couplings, which are at least twice these values, pose a challenge for the metrology of these devices and applications which require high accuracy and repeatability. We investigated the source of these variations by spatially mapping the response of a detector's fibre connector port, using a focused free-space beam, allowing us to estimate the detector's spatial non-uniformity. In addition, we realise a novel calibration approach for fibre-coupled SPADs in a free-space configuration, enabling a direct comparison between the fibre-based setup and the National Physical Laboratory's established free-space facility using a single SPAD. Finally, we investigated alternative coupling methods, testing the repeatability of different fibre-to-fibre connectors in addition to direct fibre-to-detector couplings: SPADs from three manufacturers were tested, with both single-mode and multi-mode fibre.

instruments & instrumentation,physics, applied
Note: an in Situ Method for Measuring the Non-Linear Response of a Fabry-Perot Cavity.

Wenhao Bu,Mengke Liu,Dizhou Xie,Bo Yan

DOI: https://doi.org/10.1063/1.4963361

IF: 1.6

2016-01-01

Review of Scientific Instruments

Abstract:The transfer cavity is a very important frequency reference for laser stabilization and is widely used for applications such as precision measurements and laser cooling of ions or molecules. But the non-linear response of the piezoelectric ceramic transducer (PZT) in the Fabry-Perot cavity limits the performance of the laser stabilization. Thus, measuring and controlling such non-linearity is essential. Here we report an in situ, optical method to characterize this non-linearity by measuring the resonant signals of a dual-frequency laser. The differential measurement makes it insensitive to the laser and cavity drifts, while maintaining a very high sensitivity. It can be applied for various applications with PZTs, especially in an optical lab.
Comparison of Measurements with Finite-Element Analysis of Silicon-Diaphragm-Based Fiber-Optic Fabry–Perot Temperature Sensors

Rongkun Wang,Xuejian Xie,Xiangang Xu,Xiufang Chen,Longfei Xiao

DOI: https://doi.org/10.3390/s19214780

IF: 3.9

2019-11-03

Sensors

Abstract:Silicon-diaphragm-based fiber-optic Fabry–Perot sensors with different intracavity pressures were fabricated by anodic bonding and microelectromechanical techniques. The thermal stress and thermal expansion of the Fabry–Perot (FP) sensor caused by high-temperature bonding and temperature change were simulated by finite-element analysis. The calculated thermal stress is largest in the center and edge regions of the resonance cavity, reaching from 2 to 6 MPa. The reflection spectra and temperature sensitivity of the sensors were simulated by using a two-dimensional wave-optic model in Comsol. Theoretical calculations were also made for the FP cavity without considering silicon-diaphragm deformation and thermal stress. Four sensors with intracavity pressures of 0.01, 0.03, 0.04, and 0.05 MPa were tested at low temperatures, showing a high degree of consistency with the simulation results rather than theoretical calculation, especially for high intracavity pressure. This method is expected to aid the analysis of thermal stress generated during the bonding process and to facilitate better design and control of the temperature sensitivity of the sensor.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Generalized Electrical Substitution Methods and Detectors for Absolute Optical Power Measurements

S I Woods,J E Neira,J E Proctor,J P Rice,N A Tomlin,M G White,M S Stephens,J H Lehman

DOI: https://doi.org/10.1088/1681-7575/ac72dc

Metrologia

Abstract:We have developed generalized methods for electrical substitution optical measurements, as well as cryogenic detectors which can be used to implement them. The new methods detailed here enable measurement of arbitrary periodic waveforms by an electrical substitution radiometer (ESR), which means that spectral and dynamic optical power can be absolutely calibrated directly by a primary standard detector. Cryogenic ESRs are not often used directly by researchers for optical calibrations due to their slow response times and cumbersome operation. We describe two types of ESRs with fast response times, including newly developed cryogenic bolometers with carbon nanotube absorbers, which are manufacturable by standard microfabrication techniques. These detectors have response times near 10 ms, spectral coverage from the ultraviolet to far-infrared, and are ideal for use with generalized electrical substitution. In our first tests of the generalized electrical substitution method with FTS, we have achieved uncertainty in detector response of 0.13 % (k=1) and total measurement uncertainty of 1.1 % (k=1) in the mid-infrared for spectral detector responsivity calibrations. The generalized method and fast detectors greatly expand the range of optical power calibrations which can be made using a wideband primary standard detector, which can shorten calibration chains and improve uncertainties.
Limitations due to residual interference in a fiber-based optical frequency reference at 1.55 $μ$m

Karim Manamanni,Tatiana Steshchenko,Fabrice Wiotte,Rodolphe Le Targat,Michel Abgrall,Olivier Lopez,Étienne Cantin,Paul-Éric Pottie,Anne Amy-Klein,Vincent Roncin,Frédéric Du-Burck

DOI: https://doi.org/10.48550/arXiv.2201.07468

2022-03-28

Abstract:We present an experimental investigation of the stability limits specific to optical frequency standards using a fiber-optic architecture and semiconductor lasers. A compact setup composed of a semiconductor laser frequency-locked onto an acetylene transition detected in saturated absorption has been implemented using only fiber-optic components. Fiber optic technology allows compact and reliable solutions for various applications. However, for high sensitivity and stability applications such as metrology, residual reflections induced by optical index inhomogeneities in connectors and fiber-coupled components leading to spurious interference significantly limit performance. We have examined the origin of the interference fringes superimposed on the detected signal and the limitations they cause to the frequency stability of the reference. The effects of temperature and beam power fluctuations are also examined. Our results show that the frequency stability is limited in the 10-13 range by the effect of interference fringes due to use of fiber components.

Instrumentation and Detectors,Optics
Responsivity evaluation of photonics integrated photodetectors via pairwise measurements with an attenuation circuit

Jing Zhang,Tianchen Sun,Mai Ji,Anirudh R. Ramaseshan,Aswin A. Eapen,Thomas Y.L. Ang,Victor Leong

2024-12-09

Abstract:Integrated photonics platforms offer a compact and scalable solution for developing next-generation optical technologies. For precision applications involving weak signals, the responsivity as well as the accurate calibration of the integrated photodetectors at low optical powers become increasingly important. It remains challenging to perform a calibration traceable to mW-level primary standards without relying on external attenuation setups. Here, we utilize an on-chip attenuation circuit, composed of a series of cascaded directional couplers (DCs), to evaluate the responsivity of integrated photodetectors (PDs) at uW optical power levels with mW inputs to the chip. Moreover, we show that a pairwise measurement method, involving the simultaneous measurement of the integrated PD photocurrent and an auxiliary optical output which is coupled off-chip, systematically improves the experimental uncertainties compared to a direct PD photocurrent measurement. For 3 cascaded DCs, the pairwise measurement improves the repeatability error from 1.21% to 0.22%, with an overall expanded calibration uncertainty (k=2) of 10.13%. The latter is dominated by the scattering noise floor and fiber-to-chip coupling errors, which can be significantly improved with better device fabrication control. Our method can be extended to a fully integrated calibration solution for waveguide-integrated single-photon detectors.

Optics,Applied Physics
Monochromatic Radiation Source Based on a Supercontinuum Laser for Measurement of Spectral Sensitivity of Radiation Detectors in the Range 0.9–1.6 μm with the Use of an Absolute Cryogenic Radiometer

A. Yu. Dunaev,A. S. Baturin,V. N. Krutikov,S. P. Morozova

DOI: https://doi.org/10.1007/s11018-021-01870-z

2021-02-01

Measurement Techniques

Abstract:An improved monochromatic radiation source with spectral width 4 nm based on a supercontinuum laser and double monochromator is introduced into a unit based on an absolute cryogenic radiometer in order to increase the precision of measurement of spectral sensitivity in the range 0.9–1.6 μm. A feedback system that supports stabilization of the power of monochromatic radiation with standard deviation 0.025% is developed. The power of optical radiation in the plane of the detector and/or power of the absolute cryogenic radiometer varies from 0.1 to 1.5 mW. The spectral distribution of the power of the newly developed source in different operating regimes of the supercontinuum laser is presented.
Analysis of a distributed fiber-optic temperature sensor using single-photon detectors

Shellee D Dyer,Michael G Tanner,Burm Baek,Robert H Hadfield,Sae Woo Nam,Shellee D. Dyer,Michael G. Tanner,Robert H. Hadfield

DOI: https://doi.org/10.1364/oe.20.003456

IF: 3.8

2012-01-30

Optics Express

Abstract:We demonstrate a high-accuracy distributed fiber-optic temperature sensor using superconducting nanowire single-photon detectors and single-photon counting techniques. Our demonstration uses inexpensive single-mode fiber at standard telecommunications wavelengths as the sensing fiber, which enables extremely low-loss experiments and compatibility with existing fiber networks. We show that the uncertainty of the temperature measurement decreases with longer integration periods, but is ultimately limited by the calibration uncertainty. Temperature uncertainty on the order of 3 K is possible with spatial resolution of the order of 1 cm and integration period as small as 60 seconds. Also, we show that the measurement is subject to systematic uncertainties, such as polarization fading, which can be reduced with a polarization diversity receiver.

optics
Temperature-compensated high-sensitivity refractive index, liquid level and PH sensing realization enabled by a small-period microfiber long period grating cascaded with microfiber Bragg grating

Hongtao Li,Weisheng Wang,Huojiao Sun,Hao Wu,Xu Wang,Aiyun Zheng,Lili Liang,Liang Lu,Jun Zhu,Qi Yu,Jialiang Lv,Benli Yu

DOI: https://doi.org/10.1016/j.sna.2024.115402

IF: 4.291

2024-04-23

Sensors and Actuators A Physical

Abstract:Conventional reported optical fiber sensors couldn't have both good temperature-compensated characteristic and high PH sensing sensitivity. In this study, we proposed and fabricated a small-period microfiber long period grating (SP-mFLPG) cascaded with a line-by-line microfiber Bragg grating (mFBG) by using femtosecond (fs) laser directly writing technique for high-sensitivity temperature-compensated sensing refractive index(RI), liquid level(LL), PH value. To be the different from traditional LPG devices, the temperature sensitivities of SP-mFLPG was measured as -8.61 pm/°C owing to the strong coupling occurred between the fundamental mode of TE 11 mode and the higher-order mode of TE 111 , which could be compensated with the mFBG device with a temperature sensitivity of 7.85 pm/°C. On the basis of this temperature-insensitive sensing strategy, our proposed SP-mFLPG sensor can sense RI, LL and pH with high sensitivities of 866.343 nm/RIU, 7.224 nm/mm, -5.70 nm/PH, respectively. Our obtained PH sensitivity is much higher than numerous reported state-of-the-art optical fiber PH sensors. Thus, our proposed optical microfiber device can be found potential applications in real-time measuring some important biochemical reaction procedures.

engineering, electrical & electronic,instruments & instrumentation
High-integration optical fiber sensor with Vernier effect based on spatial beam splitting

Liangtao Hou,Yan Li,Yi Liu,Min Li,Shiliang Qu

DOI: https://doi.org/10.1016/j.optlastec.2023.110415

IF: 4.939

2023-12-08

Optics & Laser Technology

Abstract:A highly integrated optical fiber sensor is theoretically and experimentally demonstrated, which can realize optical Vernier effect by spatial beam splitting structure. The split parallel beams could be generated by spliced non-equal-diameter hollow-core fibers (NED-HCFs). By optimizing mode-field distribution and self-imaging effect, the fringe visibility (FV) of the Vernier envelope can be enhanced to 5.11 dB. Experimental results show that the central air-waveguide has a high-pressure sensitivity of 43.42 nm/MPa, while the cladding-waveguide presents the immunity of wavelength to external pressure. The measured temperature sensitivity coefficients are −108.2 pm/°C for Vernier envelope, 11.5 pm/°C for cladding-waveguide. Therefore, the simultaneous measurement of pressure and temperature can be realized by using the proposed structure based on dual-parameter sensitivity matrix. Meanwhile, the sensor has a fast pressure response of 0.021 s due to the open-cavity microchannel. The proposed sensor provides a new idea for the design of optical fiber structures based on Vernier effect.

optics,physics, applied
High-resolution Temperature Fiber Ring Laser Sensor Based on Relative Intensity Noise Measurement

Jichao Jin,Yishi Liu,Yakang Liu,Xingfan Chen

DOI: https://doi.org/10.1109/jlt.2024.3435139

IF: 4.7

2024-01-01

Journal of Lightwave Technology

Abstract:High-precision fiber optic sensors are widely used due to their high stability, resistance to environmental interference, and ability to sense multiple physical quantities. However, traditional fiber optic sensors rely on spectral information as the sensing medium, which requires highprecision spectrometers. This greatly limits their use in harsh conditions and makes it difficult to achieve lower costs and faster detection speeds. To address these limitations, we propose a method based on converting spectral information into the relative intensity noise (RIN) of the light source, making it possible to detect spectra through electrical means. Taking temperature sensing as an example, the feasibility of this method is verified, showing adjustable sensitivity (measured at -172 Hz/°C in this experiment), good linearity, and a theoretical temperature resolution of 10-5 °C. RIN is a type of noise present in all light sources and is easy to acquire, giving this method significant engineering application value. By eliminating the need for spectrometers in fiber optic sensors, this approach reduces the complexity and cost of detection
Development of a detector-based absolute spectral power responsivity scale in the spectral range of 300–1600 nm

Abdallah M. Karmalawi,Alaaeldin A. Abdelmageed

DOI: https://doi.org/10.1007/s10854-021-05253-6

2021-02-01

Abstract:The radiometry laboratory at the National Institute of Standards (NIS) has taken in his shoulder to develop and improve the spectral responsivity facilities to get high precision and more reliable optical detectors measurements. During the last few years, the calibration of the detectors was refined as well as the reliability of spectral responsivity results, especially in the critical ultra-violet and infrared range of the spectrum. This setup was constructed using a lamp-monochromator-based setup accompanied by a silicon trap detector and an Indium Gallium Arsenide (InGaAs) detector to extend the scale to the infrared (IR) spectral region. Both detectors are traceable and shown to be spatially uniform, linear, stable, and capable of disseminating an absolute spectral responsivity scale. The uncertainty contribution of the spectral responsivity for a silicon-based detector is less than 1–1.9% for the spectral range 300–1100 nm, and about 2–3.8 % (<i>k</i> = 2) for InGaAs-based detector in the wavelength range 800–1600 nm. Additionally, this paper gives a comprehensive overview of' NIS's spectral responsivity facilities, which are now fully automated and controlled by LabVIEW.
Femtosecond laser fabricated all-optical fiber sensors with ultrahigh refractive index sensitivity: modeling and experiment

Lan Jiang,Longjiang Zhao,Sumei Wang,Jinpeng Yang,Hai Xiao

DOI: https://doi.org/10.1364/OE.19.017591

2011-08-29

Abstract:All-optical fiber sensors based on ultracompact fiber inline Mach-Zehnder interferometer (MZI) are fabricated by side-ablating a U-shape microcavity in a single-mode optical fiber with the fiber core partially removed using femtosecond (fs) laser pulses, in which the two light paths are accordingly formed in the remaining D-type fiber core and the U-shape microcavity. Beam propagation method (BPM) analysis is utilized to illustrate the dependences of good transmission spectra on parameters including the ablation depth, ablation length and the refractive index of U-shape micocavity, which gives some guidelines to optimize parameters for fs laser micromachining and predicts RI (refractive index) sensitivities within given RI ranges. The modeling results of ultrahigh RI sensitivities for gases and solutions are -3243.75 ± 0.65nm/RIU (refractive index unit) and -10789.29 ± 18.91nm/RIU, respectively. In RI testing experiments, the sensor exhibits ultrahigh RI sensitivities of -3754.79 ± 44.24nm/RIU with refractive indices ranging from 1.0001143 to 1.0002187 by testing different mixture ratios of N2 and He gases, and -12162.01 ± 173.92nm/RIU with refractive indices ranging from 1.3330 to 1.33801 by testing different concentrations of sucrose solutions, which is essentially in agreement with the modeling results.
Temperature-insensitive refractive index sensor based on high-order-resonance short-line long-period fiber grating

Wenyi Bu,Xicheng Wang,Zhifang Wu,Jing Lin,Perry Ping Shum,Jixiong Pu

DOI: https://doi.org/10.1016/j.sna.2023.114540

2023-07-05

Abstract:Long-period fiber grating based refractometers have attracted great attention for various applications, but they usually suffer from the cross sensitivity to temperature in practice. Here, we demonstrate a temperature-insensitive refractive index sensor based on a short-line long-period fiber grating (SL-LPFG). It is fabricated by using femtosecond laser to periodically inscribe short lines in a standard single-mode fiber (SMF) with a small duty cycle of 0.3, and resonates to a cladding mode with a high diffraction order. This high-order-resonance SL-LPFG responds to ambient refractive index with the sensitivities of 175.84 nm/RIU and 367.63 nm/RIU in the ranges of 1.3381 to 1.3763 and 1.3763 to 1.4008, respectively. Meanwhile, it presents a temperature sensitivity as low as 4.0 pm/°C, which is almost one percent of the temperature sensitivity of the similar period LPFG fabricated by UV exposure method. It's significant for LPFG-based refractometers in normal SMFs to minimize thermal interference without the assistance of an additional sensing unit and matrix interrogation. Therefore, the proposed high-order-resonance SL-LPFG provides a high-performance and low-cost solution for refractive index related applications, especially in medical, chemical, and biological fields.

engineering, electrical & electronic,instruments & instrumentation
An Optical Fiber Pressure Sensor Based on F-P Interferometry and Intensity Demodulation

DENG Yuan-long,ZHAO Xiao-li,LI Xue-jin,GENG You-fu,HONG Xue-ming,QIU Cheng-jun

DOI: https://doi.org/10.3969/j.issn.1000-2618.2011.01.002

2011-01-01

Abstract:An optical fiber pressure sensor was designed,fabricated and characterized.It employed a Fabry-Perot (F-P) interferometer and simple intensity-demodulation technology.A square silicon cup processed by anisotropic etching serves as sensitive element for the better consistency than that of circular diaphragm.A large area ratio of the moving mirror to the stationary one is introduced to reduce the nonlinearity due to the non-planarity of the deflection.Reference light generated from a 2×2 optical fiber coupler is used to decrease the influence of intensity variations of the light source.Single-value measurement was achieved under the pressure range from 0 to 38 kPa.The experimental results demonstrate an upmost relative sensitivity of 0.7%/kPa and a reasonable repeatability,consisting well with the theoretical analysis and simulation.A new method of multi-wave or multi-sensor is presented to expand the measurement range with high sensitivity.
Measurable Refractive Index Range for a Doubly Cladding Single Mode Fiber Sensor and Its Application in Temperature and Humidity Sensing

Xiao-Kang Zhang,Lu Lan,Zhen Kong,Lihua Chen,Zhiren Ye

DOI: https://doi.org/10.1117/12.870121

2010-01-01

Abstract:A new type of evanescent field sensors based on a doubly cladding single mode fiber is proposed. The theoretical analysis shows that the measurable refractive index (RI) ranges for the sensors are limited in the single mode in the fiber becoming leaky and the range is less than the RI difference between the core and the cladding of the fibers. Two temperature sensors and a humidity sensor were fabricated. One temperature sensor showed a good linear response in a range of 60°C, the modulation depth of 40 dB, and the insertion loss of -1.4 dB. The humidity sensors fabricated by agarose gel had a measurable moisture range of 16 ~ 100% of RH. Its optical power variation with humidity is 8.5 dB and insertion loss is 3.9 dB. We confirmed that the DC single mode fiber sensors became a new type of intensity sensors characterized in good linear response, low insertion loss, high modulation depth, and low cost in fabrication.
High-Resolution and Large-Dynamic Range Fiber-Optic Sensors Based on Dual-Mode Direct Spectrum Interrogation Method

Min Zhou,Zhe Zhang,Qingyue Cui,Qingdian Lin,Jun Yu,Xiaoyang Guo,Cangtao Zhou,Shuangchen Ruan

DOI: https://doi.org/10.3390/s24123996

IF: 3.9

2024-06-20

Sensors

Abstract:Conventional optical fiber temperature/strain sensors often have to make compromises between the resolution and the dynamic range. Here we present a new method that meets the measurement requirements for both high resolution and large dynamic range. A high-quality optical fiber Fabry-Perot Interferometer (FPI) constructed using a pair of chirped fiber Bragg gratings is employed as the sensor and a dual-mode direct spectrum interrogation method is proposed to identify the small drift of external temperature or strain. As a proof-of-concept illustration, a temperature resolution of 0.2 °C within 30–130 °C is demonstrated. For strain sensing, the resolution can be 10 με within 0–1000 με. The measurement resolution can be improved further by routinely increasing the reflectivity of the CFBG and the cavity length and the sensor can also be mass-produced. This new sensing schema not only resolves the conflict between the resolution and the dynamic range of fiber-optic temperature/strain sensors but can also be extended to other sensors and measurands.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation

Sequence Note: Genetic Characterization of the V3 Loop Sequences of 21 HIV Type 1 Spanish Isolates from Hemophilia Patients

Measuring the Refractive Index of Optical Adhesives at Cryogenic Temperatures.

Measurement of Polarization Mode Couplings in Polarization-Maintaining Fibers Based on White Light Interference

Verification of calibration methods for determining photon-counting detection efficiency using superconducting nano-wire single photon detectors

Traceable characterisation of fibre-coupled single-photon detectors

Note: an in Situ Method for Measuring the Non-Linear Response of a Fabry-Perot Cavity.

Comparison of Measurements with Finite-Element Analysis of Silicon-Diaphragm-Based Fiber-Optic Fabry–Perot Temperature Sensors

Generalized Electrical Substitution Methods and Detectors for Absolute Optical Power Measurements

Limitations due to residual interference in a fiber-based optical frequency reference at 1.55 $μ$m

Responsivity evaluation of photonics integrated photodetectors via pairwise measurements with an attenuation circuit

Monochromatic Radiation Source Based on a Supercontinuum Laser for Measurement of Spectral Sensitivity of Radiation Detectors in the Range 0.9–1.6 μm with the Use of an Absolute Cryogenic Radiometer

Analysis of a distributed fiber-optic temperature sensor using single-photon detectors

Temperature-compensated high-sensitivity refractive index, liquid level and PH sensing realization enabled by a small-period microfiber long period grating cascaded with microfiber Bragg grating

High-integration optical fiber sensor with Vernier effect based on spatial beam splitting

High-resolution Temperature Fiber Ring Laser Sensor Based on Relative Intensity Noise Measurement

Development of a detector-based absolute spectral power responsivity scale in the spectral range of 300–1600 nm

Femtosecond laser fabricated all-optical fiber sensors with ultrahigh refractive index sensitivity: modeling and experiment

Temperature-insensitive refractive index sensor based on high-order-resonance short-line long-period fiber grating

An Optical Fiber Pressure Sensor Based on F-P Interferometry and Intensity Demodulation

Measurable Refractive Index Range for a Doubly Cladding Single Mode Fiber Sensor and Its Application in Temperature and Humidity Sensing

High-Resolution and Large-Dynamic Range Fiber-Optic Sensors Based on Dual-Mode Direct Spectrum Interrogation Method