Abstract:Continuous basalt fiber (CBF) is a new type of performance outstanding inorganic nonmetallic material. In comparison with carbon fibers, basalt fibers exhibit greater failure strain as well as better impact and fire resistance with less poisonous fumes and 50% cost reduction. It is also known that basalt fibers display higher mechanical properties, better chemical stability and superior thermal and electrical insulation as compared with glass fibers. Basalt fiber has been widely used as a reinforcing composite material for construction industry and for preparation of polymer matrix composites. As high-performance low-cost reinforcements, basalt fibers should have a great potential for strengthening metal matrix composites (MMCs) and reducing their preparation cost. However, so far, few reports focused on the investigation on metal matrix composites reinforced by continuous basalt fibers, especially for lack of feasible fabrication technologies. Thus, in the present work, two-dimensional continuous basalt fiber cloth and Al12Si alloys foils were selected as raw materials and alternately stacked to obtain a sandwiched structure. Subsequently, vacuum pressure infiltration was utilized to fabricate aluminum matrix composites reinforced by continuous basalt fibers (CBF/Al) with volume fraction of 65% successfully. Influence of infiltration parameters on microstructure evolution of resulting aluminum matrix composites was investigated and formation mechanism of multi-layered structure of CBF/Al composite was clarified. Moreover, mechanical properties of the multi-layered CBF/Al composite were evaluated. The results showed that when the infiltration parameters were 660., 10 MPa and 10 min, fully dense CBF/Al composite could be achieved and the novel composite displayed a unique multi-layered structure, namely continuous basalt fibers in forms of cruciform crossing distributed within aluminum alloys matrix. It is noteworthy that no obvious chemical reaction happened between continuous basalt fibers and Al-12Si alloys, and sound metallurgical bonding interface between them was obtained due to the interdiffusion of Al and Si elements. Unfortunately, mechanical properties of multi-layered CBF/Al composite did not reach a desired level, which was attributed to (i) decreasing of effective load-carrying capacity due to the imperfect distribution manner of continuous basalt fibers and (ii) deteriorating of intrinsic mechanical properties at high temperature.

Basalt Short Fibers Dispersion and Fabric Impregnation with Magnesium Alloy (AZ63): First Results

Preparation and Performance of the Magnesium Matrix Composite Reinforced with Al2O3-SiO2 Short Fibers

Development of AZ91D Magnesium Alloy-Graphene Nanoplatelets Composites Using Thixomolding Process

Graphene Nanoplatelets Reinforced Magnesium Matrix Composites Fabricated by Thixomolding

Silicon carbide-embedded AZ91E alloy nanocomposite hybridised with chopped basalt fibre: performance measures

Mechanical properties and microstructure of basalt fiber-biobased- basic magnesium sulfate cement

Fabrication and Characterization of Magnesium Matrix Composite Processed by Combination of Friction Stir Processing and High-Energy Ball Milling

Fabrication of Alumina Silicate Short Fibers Reinforced AZ91 Metal Matrix Composites

Interfacial and Fracture Behavior of Short-Fibers Reinforced AE44 Based Magnesium Matrix Composites

Mechanical Properties, Aging Behavior and Microstructure Evolution of Mg-Nd-Zn-Zr Based Magnesium Matrix Composite Reinforced with Alumina Fibers

Fabrication and Mechanical Characteristics of Multi-Laminated Aluminum Matrix Composites Reinforced by Continuous Basalt Fibers

Basalt Fiber-Reinforced Epoxy Laminates: Improvement in Quasi-Static and Fatigue Properties with Modified Matrices and Fiber Surfaces Using Silica Nanoparticles

Investigation on Mechanical and Fracture Behavior of Magnesium Composite Reinforced With Hybrid Fly Ash Particulates Synthesized via Friction Stir Processing Route

Magnesium-based nanocomposites synthesized using friction stir processing: an experimental study

Development of High Performance Magnesium Matrix Nanocomposites Using Nano-SiC Particulates As Reinforcement

MECHANICAL BEHAVIOR OF COMPOSITE BASALT SHORT FIBER FOR CONCRETE STRUCTURE REINFORCEMENT

Fabrication technology and material characterization of carbon fibre reinforced magnesium

Sustainable Basalt Fibers vs. Traditional Glass Fibers: Comparative Study on Thermal Properties and Flow Behavior of Polyamide 66-Based Composites

Mechanical Behaviour of As-Manufactured and Repaired Aligned Discontinuous Basalt Fibre-Reinforced Vitrimer Composites

Enhancing the Mechanical Properties of Basalt Fiber and Stainless Steel Wire Mesh Composites Incorporating Fire Retardants Through Response Surface Methodology Optimization

Mechanical and Wear Behaviour of Nano-Fly Ash Particle-Reinforced Mg Metal Matrix Composites Fabricated by Stir Casting Technique