Abstract:Context: Powder metallurgy uses metallic and/or non-metallic powders that, through mixing, compacting, and sintering operations, allow obtaining large series of products. In austenitic stainless steels, Cr23C6-type carbides can precipitate at temperatures between 450 and 950 °C. When this occurs, the steel is susceptible to being attacked at its grain boundaries by a phenomenon called sensitization. Titanium is added as a ‘stabilizer’ because it has a greater affinity with carbon for the formation of species at a temperature of approximately 900 oC, and, during cooling, it consumes the carbon forming MC-type carbides, inhibiting the precipitation of Cr23C6. Method: The composition and morphology of the powders were characterized, leading to the formulation of an alloy matrix consisting of a mixture of AISI 316 steel powders of two different particle-size distributions in a proportion that produced the highest density and the lowest porosity in the sintered material. Titanium was added at two levels (0,4 and 1,0 wt%), and sintering was carried out with nitrogen. The corrosion rate was determined by potentiodynamic polarization. Vickers hardness and pin-on-disk wear tests were performed. The stages were complemented with a microstructural analysis. Results: The addition of 0,4 wt% of titanium decreased the steel’s rate of corrosion, albeit in the absence of passivation. The microstructure consists of austenite, ferrite, and TiC precipitates. The addition of 1,0 wt%Ti showed an increase in the corrosion rate, with a microstructure containing austenite, ferrite, TiC carbides, and the Laves ɳ-Fe2Ti phase. Conclusions: The results were compared against thermodynamic simulations in the Thermo-Calc software, which were consistent with the microstructural analysis, showing the phenomena of stabilization as well as the precipitation of intermetallic phases and highlighting the importance of establishing strict controls in the formulation of powder metallurgical alloys due to the transformations that can take place due to the effect of the thermal cycles of the process.

Improvement of Adhesive Wear Behavior by Variable Heat Treatment of a Tool Steel for Sheet Metal Forming

Effects of Nitriding and Thermal Processing on Wear and Corrosion Resistance of Vanadis 8 Steel

Optimization of wear-, fracture- and corrosion performance of Vanadis 6 steel through cryogenic treatment and tempering

Enhancing tribological performance in PM Vanadis 6 steel through optimization of cryogenic and tempering treatment

A Multivariate Experimental Design to Investigate the Effect of Different Heat Treatment Procedures and Parameters' Interactions on the Hardness and Retained Austenite of K340 Cold-work Tool Steel

Effect of Cryogenic Treatments on Hardness, Fracture Toughness, and Wear Properties of Vanadis 6 Tool Steel

The effect of deep cryogenic treatments on the mechanical properties of an AISI H13 steel

Improvement of wear and hot melt loss resistance of metal carbide layers on H13 steel

Effect of Different Post-Processing Thermal Treatments on the Fracture Toughness and Tempering Resistance of Additively Manufactured H13 Hot-Work Tool Steel

Evaluation of factors influencing deep cryogenic treatment that affect the properties of tool steels

Adapting the Surface Integrity of High-Speed Steel Tools for Sheet-Bulk Metal Forming

Effect of Heat Treatment Temperature on the Microstructure, Wear and Friction of Ni–Nb–V Alloyed Manganese Steel

Effect of Cryosoaking Period and Soft-Tempering Temperature on Wear Behavior of AISI H13 Steel

Effect of Tempering Temperature on Microstructure and Properties of a New Type of Nitrogen‐Containing Hot‐Work Die Steel 3Cr7Mo2NiSiVN

Effect of Heat Treatment Parameters on the Modification of Nano Residual Austenite of Low-Carbon Medium-Chromium Steel

Improved Adhesion and Tribological Properties of AlTiN-TiSiN Coatings Deposited by DCMS and HiPIMS on Nitrided Tool Steels

Innovations in Cold Work Tool Steels- Research and Development

Influence of austenitising temperature on micro-scale abrasive wear of Ni-modified ferritic stainless steel

Improving mechanical properties of carbon and tool steels via chromizing

Study Of the Effect of Titanium Additions on The Mechanical and Corrosion Properties of AISI 316 Powder Metallurgical Steel

Effect of Plasma Nitriding Pretreatment on the Mechanical Properties of AlCrSiN-Coated Tool Steels