Electrodialytic remediation of CCA-treated waste wood in a 2 m(3) pilot plant.

I. V. Christensen,A. J. Pedersen,L. Ottosen,A. Ribeiro

DOI: https://doi.org/10.1016/J.SCITOTENV.2005.11.018

2006-07-01

Abstract:

What problem does this paper attempt to address?

Bioaerosols emission and exposure risk of a wastewater treatment plant with A2O treatment process

Yunping Han,Kaixiong Yang,Tang Yang,Mengzhu Zhang,Lin Li

DOI: https://doi.org/10.1016/j.ecoenv.2018.11.018

Abstract:The characteristics of bioaerosol emissions from wastewater treatment plants (WWTPs) have attracted extensive attention. The anaerobic-anoxic-oxic (A2O) process, which uses the activated sludge approach to wastewater treatment, is the most widely used process in WWTPs. Concentration, size distribution, population, and exposure risk from bacteria and fungi in bioaerosols of WWTPs using the A2O process were studied in this work. The results showed that the maximum concentration of airborne bacteria (1.00 × 104 Colony Forming Units per cubic meter (CFU m-3)) and fungi (1.44 ×104 CFU m-3) occurred from the facility's aerobic tank, in summer. As one of the main factors affecting bioaerosol exposure risk, particle size distribution was related to season. The study found that particles larger than 3.3 µm in diameter were detected mainly in spring and summer, while particles less than 3.3 µm were detected mainly in autumn and winter, whether bacterial aerosol or fungal aerosol. In addition, pathogenic bacteria were observed in bioaerosols from WWTPs, with 18 of the 65 species of bacteria detected found to be potentially or opportunistically pathogenic, such as Chryseobacterium, Stenotrophomonas, Alcaligenes, Micrococcus, Pantoea, Enterobacter and Escherichia-Shigella. The presence of these pathogens further increased the exposure risk from bioaerosols. The results of an inhalation risk assessment for airborne bacteria and fungi indicated that potential adverse health risks for adults mainly occurred in spring, summer, and autumn. On this basis, it was concluded that WWTP operators should set up effective bioaerosol controls as soon as possible to protect the health of workers, and of residents near the plant.
The generation characteristics, pattern, and exposure risk of bioaerosol emitted in an A2O process wastewater treatment plant

Yanjie Wang,Kai Yang,Xuebin Guo,Shan Zhao,Zhiqiang Lu,Liying Yang,Huiling Song,Guoyu Zhou

DOI: https://doi.org/10.1016/j.ecoenv.2022.113823

IF: 7.129

2022-08-01

Ecotoxicology and Environmental Safety

Abstract:Bioaerosols can be generated in wastewater treatment plants (WWTPs), they may contain pathogenic bacteria, cause disease transmission, and attract the public's attention. In this study, bioaerosols were collected from seven different stages of an A²O process WWTP. The component characteristics were analyzed by bacterial culture and high-throughput sequencing. The correlations in different processes were analyzed, and the health risks of bioaerosols produced were evaluated. The results showed that the concentration range of bacteria aerosol in the WWTP was 75 CFU/m³-706 CFU/m³. The concentration range of total suspended particles was 111.13 µg/m³-211.67 µg/m³, the primary water-soluble ions were Ca²⁺ and Cl⁻. In the air of each stage, the main bacteria were Cetobacterium, Bacteroides, Romboutsia, and the fungi were Fusarium, Alternaria, and Aspergillus. The dominant bacteria in the wastewater were Cetobacterium, Romboutsia, Stenotrophobacter, and the fungi were Fusarium, Aspergillus, and Mortierella. The total bacterial concentration and ion concentration in the aerobic section of the biochemical tank were the highest. The results of species composition and principal component analysis showed that the bacterial composition in the air at different processes was similar, while the bacteria in wastewater differed significantly. Among them, the wastewater bacteria in the aerobic section of the biochemical tank were closer to that in the air. Fungal results were similar to bacteria but not prominent. The bioaerosol exposure risk results show that the risk in each stage was acceptable (5.15 ×10⁻⁴-6.47 ×10⁻³). However, the exposure risk of bioaerosol was calculated by the total bacterial concentration. In fact, some pathogenic microorganisms such as Escherichia coli and Aspergillus flavus were detected in bioaerosols, which may cause hemorrhagic colitis, cancer and other diseases by swallowing and inhalation. Therefore, the risk might be underestimated and should be a cause of concern.

environmental sciences,toxicology
Cultivation-dependent and Cultivation-Independent Investigation of O-methylated Pollutant-Producing Bacteria in Three Drinking Water Treatment Plants

Yiran Tang,Zhixuan Wu,Yanfen Zhang,Chuanxuan Wang,Xuelian Ma,Kejia Zhang,Renjie Pan,Yucheng Cao,Xinyan Zhou

DOI: https://doi.org/10.1016/j.watres.2023.119618

IF: 12.8

2023-01-01

Water Research

Abstract:O-methylated pollutants (OMPs) are emerging contaminants in drinking water and mainly produced through bacterial O-methylation. However, the information of OMP-producing bacteria (OMPPB) in drinking water treatment plant (DWTP) is largely unknown so far. In this study, the OMPPB in water samples from three DWTPs (XL, JX and NX) were investigated by using cultivation-dependent and cultivation-independent technologies. Four OMPs were detected and their odor and toxicity risks were assessed. Formation potentials (FPs) of 2,4,6-trichloanisole, 2,3,6-trichloanisole, 2,4,6-tribromoanisole, pentachloroanisole and diclofenac methyl ester were determined in water samples and their values shifted significantly among DWTPs. A most probable number (MPN) method was established to quantify OMPPB numbers and the relationships between total haloanisole FPs (HAFPs) (y) and OMPPB numbers (x) in three DWTPs could be described by the following functions: y = 0.496x0.373 (XL), y = 0.041x0.465 (JX) and y = 0.218x0.237 (NX). Several genera like Bacillus, Ralstonia, Bre-vundimonas, etc. were newly found OMPPB among the cultivable bacteria, and their OMP products were eval-uated in terms of quantity and environment risks (odor, toxicity and bioaccumulation). High-throughput sequencing revealed treatment process was the main driving factor to shape the OMPPB community structures and Mantel test showed HAFP profile was significantly influenced by Mycobacterium and Pelomonas. PICURSt2 analysis discovered four phenolic O-methyltransferases (OMTs) and four carboxylic OMTs which might be responsible for OMP formation. Several strategies were recommended to assess risk and control contamination brought by OMPPB in DWTPs.
Linking aerosol characteristics of size distributions, core potential pathogens and toxic metal(loid)s to wastewater treatment process

Tang Yang,Lu Jiang,Yunping Han,Jianwei Liu,Xiaodong Wang,Xu Yan,Junxin Liu

DOI: https://doi.org/10.1016/j.envpol.2020.114741

IF: 8.9

2020-09-01

Environmental Pollution

Abstract:Wastewater treatment plants (WWTPs) play important roles in water purification but are also important source of aerosols. However, the relationship between aerosol characteristics and wastewater treatment process remains poorly understood. In this study, aerosols were collected over a 24-month period from a WWTP using a modified anaerobic-anoxic-oxic process. The aerated tank (AerT) was characterized by the highest respiratory fraction (RF) concentrations (861–1525 CFU/m3) and proportions (50.76%–65.96%) of aerosol particles. Fourteen core potential pathogens and 15 toxic metal(loid)s were identified in aerosols. Mycobacterium was the genus that aerosolized most easily in fine grid, pre-anoxic tank, and AerT. High wastewater treatment efficiency may increase the emission of RF and core potential pathogens. The median size of activated sludge, richness of core potential pathogens in wastewater, and total suspended particulates were the most influential factors directly related to the RF proportions, core community of potential pathogens, and composition of toxic metal(loid)s in WWTP aerosols, respectively. Relative humidity, temperature, input and removal of biochemical oxygen demand, dissolved oxygen, and mixed liquor suspended solids could also directly or indirectly affect the aerosol characteristics. This study enhances the mechanistic understanding of linking aerosol characteristics to treatment processes and has important implications for targeted manipulation.

environmental sciences
Bioaerosol-related studies in wastewater treatment plant with anaerobic-anoxic-oxic processes: Characterization, source analysis, control measures

Jianwei Liu,Jingyun Ge,Xinyue Kang,Hongyu Tian

DOI: https://doi.org/10.1016/j.jenvman.2023.117760

IF: 8.7

2023-04-09

Journal of Environmental Management

Abstract:Sewage in wastewater treatment plants (WWTPs) can produce fugitive bioaerosols that pose a health risk to employees and residents. This study aimed to fugitive bioaerosols from two WWTPs with anaerobic-anoxic-oxic (AAO) processes, and bioaerosols control measures were proposed based on the results of these studies. It was found that the bioaerosols were mainly composed of microorganisms from dominant genera such as Romboutsia, Rubellimicrobium, Sphingomonas, Acidea, Cryptotrichosporon and water-soluble ions dominated by SO 4 2− . Moreover, total suspended particulate (TSP), relative humidity (RH), wind speed (WS), Ca 2+ , NH 4 + , Na + , Cl − , NO 3 − , and K + had positive effects on most dominant genera, while temperature (T) and SO 4 2− had negative effects on most dominant genera. The source analysis showed that the bioaerosols in the indoor treatment facility's fine screen room and sludge dewatering plant mainly originated from sewage or sludge, and those in the aeration tank of the outdoor treatment facility mainly originated from the background air of WWTPs . By combining the characteristics of bioaerosols and the results of source analysis, targeted control measures were proposed from three aspects: source reduction of bioaerosol fugitives, control of bioaerosol propagation, and collection and treatment systems. This study provides the theoretical basis and ideas for controlling bioaerosols in WWTPs with AAO processes.

environmental sciences
Editorial: Will the real neutrophil please stand up?

K. Zarember,D. Kuhns

DOI: https://doi.org/10.1189/jlb.0711334

2011-12-01

Journal of Leukocyte Biology

Abstract:Discussion on exudate neutrophils as a more accurate model of the “working” functional in vivo neutrophil than their circulating progenitors.
Bioaerosol in a typical municipal wastewater treatment plant: concentration, size distribution, and health risk assessment

Pengcheng Xu,Chongmiao Zhang,Xiao Mou,Xiaochang C Wang

DOI: https://doi.org/10.2166/wst.2020.416

Abstract:An investigation on bioaerosol in a wastewater treatment plant (WWTP) located in Xi'an, China, was conducted to understand the characteristics of bioaerosol released from wastewater and sludge treatment facilities because the bioaerosols may pose a threat to human health. Using the Andersen impactor sampler collection and colony-counting method, bioaerosol concentrations and size distributions were detected. The risk quotient method was used to evaluate the health risks associated with inhalation of bioaerosol for WWTP staff, based on the average daily dose rates of exposure. The health risk in relation to Legionella pneumophila was quantitatively calculated using quantitative microbial risk assessment (QMRA), based on the assumption of the percentage. The maximum concentration of airborne bacteria (3,767 ± 280 colony forming units (CFU)/m3) and fungi (8,775 ± 406 CFU/m3) occurred from the aerated grit chamber and sludge thickening house, respectively, which all exceeded 500 CFU/m3 as the acceptable guideline proposed by the American Conference of Governmental Industrial Hygienists. The particle size of airborne bacteria was mainly distributed in the first three stages (>3.3 µm), while that of airborne fungi was from the second to the fourth stage (2.1-7.0 µm). The hazard index exposure to bioaerosol for adult males and females by inhalation were higher than 1. The proportion of L. pneumophila should be strictly controlled below 10-8, based on the QMRA approach.
Quantitative microbial risk assessment with nasal/oral breathing pattern for S. aureus bioaerosol emission from aeration tanks and residual sludge storage yard in a wastewater treatment plant

Cheng Yan,Xiao-yan Zhao,Xi Luo,Dong-zi An,Hao Zhu,Ming Li,Xiao-jun Ai,Wajid Ali

DOI: https://doi.org/10.1007/s11356-022-23621-5

IF: 5.8

2022-10-21

Environmental Science and Pollution Research

Abstract:AbstractA large number of pathogenic bioaerosols are generated during the treatment process of wastewater treatment plants (WWTPs), and they can pose potential risks to human health. Therefore, this study systematically analyzed the emission characteristics of Staphylococcus aureus bioaerosols released from an inverted umbrella aeration tank, a microporous aeration tank, and a residual sludge storage yard in a WWTP, and quantitatively evaluated the health risks of four kinds of exposed populations with nasal/oral breathing patterns under optimistic and conservative estimations. The results displayed that the bioaerosol concentration in inverted umbrella aeration tank was higher than that in microporous aeration tank and residual sludge storage yard. Aerosolization ratio in residual sludge storage yard was an order of magnitude lower than that in aeration tanks. Sludge workers were at higher health risks than the other three exposed populations. The health risks of nasal breathers (infection risk: 1.62 × 10−5–2.56 × 10−3 pppy; disease burden: 4.24 × 10−8–6.72 × 10−6 DALYs pppy) were 0.61–0.63 times higher than those of oral breathers (infection risk: 9.95 × 10−6–1.59 × 10−3 pppy; disease burden: 2.61 × 10−8–4.18 × 10−6 DALYs pppy). For female field engineers using oral breathing, laboratory technicians, and researchers without personal protective equipment (PPE), infection risk and disease burden had the opposite results, which indicated that satisfying one certain benchmark did not mean absolute safety. In addition, health risks of exposed populations were reduced by an order of magnitude after wearing PPE. This study can provide a reliable theoretical basis for the risk prevention of bioaerosols and supply data support for the strategies of health risk control perspectives for local sewage utilities.

environmental sciences
Bioaerosols in deodorization covers of wastewater treatment plants: Emission characteristics and health risks

Shan Zhao,Yang Liu,Jiang Chang,Jiawei Wang,Hao Peng,Baocong Cui,Jin Bai,Yanjie Wang,Linlin Hua

DOI: https://doi.org/10.1016/j.chemosphere.2024.141552

IF: 8.8

2024-03-01

Chemosphere

Abstract:Wastewater treatment plants (WWTPs) are the main source of bioaerosol emissions. The cover of deodorization within WWTPs serves not only to manage odors but also to limit the dispersion of bioaerosols. This study investigated the emission characteristics and exposure risks of bioaerosols inside deodorization covers from a WWTP in Northern China. The results revealed that the concentration of bacteria in bioaerosols ranged from 96 ± 8 to 706 ± 45 CFU/m 3 , with the highest concentration observed in the biochemical reaction tank. The predominant bacterial genera in bioaerosols within the odor control covers were Cetobacterium , Romboutsia , Bacteroides , Lactobacillus , and Tubricibacter , while the dominant fungal genera included Aspergillus , Alternaria , Fusarium , and Cladosporium . The main water-soluble ions in the air were NH 4 + , Ca 2+ , SO 4 2− , and Cl − . SO 4 2− was found to promote the survival of Cetobacterium, Brevibacterium, Fusarium, Penicillium, and Filobasidium , while Cl − exhibited inhibitory effects on most microorganisms in bioaerosols. Source tracker analysis indicated that wastewater was the primary source of bioaerosols in the biochemical reaction tank. The non-carcinogenic risk associated with bioaerosols within deodorization covers was less than 1 (2.34 × 10 −9 to 3.08 × 10 −2 ). FunGuild fungal functional prediction suggested that the abundance of animal pathogens was highest in the bioaerosols from the anaerobic sedimentation tank. BugBase phenotypic prediction showed that the abundance of potential pathogens in secondary sedimentation tank bioaerosols was the highest. This study effectively revealed the characteristics and sources of bioaerosols in the sewage and sludge treatment area under the deodorization cover, which provided a theoretical basis for enhancing the management and control of bioaerosols.

environmental sciences
Bioaerosols emission characteristics from wastewater treatment aeration tanks and associated health risk exposure assessment during autumn and winter

Xiao-yan Zhao,Dong-zi An,Man-li Liu,Jia-xin Ma,Wajid Ali,Hao Zhu,Ming Li,Xiao-jun Ai,Zaheer Ahmad Nasir,Sonia Garcia Alcega,Frederic Coulon,Cheng Yan

DOI: https://doi.org/10.1016/j.scitotenv.2022.158106

2022-12-10

Abstract:Aeration tanks from activated sludge wastewater treatment plants (WWTPs) can release a large amount of bioaerosols that can pose health risks. However, risk characterization of bioaerosols emissions form wastewater treatment plants is currently not systematically carried out and still in its infancy. Therefore, this study investigated emission characteristic of two indicator model bioaerosols Staphylococcus aureus and Escherichia coli, emitted from aeration tanks of a municipal WWTP. Monte Carlo simulation was then used to quantitatively assess microbial risk posed by different aeration modes under optimistic and conservative estimates. Further to this, two different exposure scenarios were considered during 3 days sampling campaign in autumn and winter. Results showed that the bioaerosol concentration from microporous aeration tank (20–262 CFU m−3) was one order of magnitude lower than rotating disc aeration tank. Average aerosolization rate was 7.5 times higher with mechanical aeration mode. Health risks of exposed populations were 0.4 and 9.6 times higher in winter than in autumn for E. coli and S. aureus bioaerosol, respectively. Health risks of staff members were 10 times higher than academic visitors. Interesting results were observed for academic visitors without personal protective equipment (PPE) respectively exposed to S. aureus and E. coli bioaerosol in autumn and winter: while the derived infection risk met the United States Environmental Protection Agency (U.S. EPA) benchmark under optimistic estimation, the disease risk burden was over the World Health Organization (WHO) benchmark under conservative estimation. These revealed that only satisfying one of the two benchmarks didn't mean absolute acceptable health risk. This study could facilitate the development of better understanding of bioaerosol quantitative assessment of risk characterizations and corresponding appropriate risk control strategies for wastewater utilities.

environmental sciences
Bioaerosol emissions from wastewater treatment process at urban environment and potential health impacts

Yogesh Kumar Vishwakarma,Mayank,Kirpa Ram,Mukunda M Gogoi,Tirthankar Banerjee,R S Singh

DOI: https://doi.org/10.1016/j.jenvman.2024.121202

Abstract:The inlet of wastewater treatment plants (WWTPs) contains pathogenic microorganisms which during aeration and by mechanical mixing through wind typically aerosolized microbes into ambient air. Bioaerosol emission and its characterization (bacterial and fungal) was investigated considering low-flow and high-flow inlet of wastewater treatment plant. Generation of bioaerosols was found influenced by prevailing seasons while both during summer and winter, fungal concentration (winter: 1406 ± 517; summer: 1743 ± 271 CFU/m3) was higher compared to bacterial concentration (winter: 1077 ± 460; summer: 1415 ± 588 CFU/m3). Bioaerosols produced from WWTPs were predominately in the size range of 2.1-4.7 μm while fraction of fungal bioaerosols were also in ultra-fine range (0.65 μm). Bioaerosols reaching to the air from WWTPs varied seasonally and was calculated by aerosolization ratio. During summer, aerosolization of the bioaerosols was nearly 6 times higher than winter. To constitute potential health effects from the exposure to these bioaerosols, biological characterization, antibiotics resistance and the health survey of the nearby area were also performed. The biological characterization of the bioaerosols samples were done through metagenomic approach using 16s and ITS metagenomic sequencing. Presence of 167 genus of bacteria and 41 genus of fungi has been found. Out of this, bacillus (73%), curtobacterium (21%), pseudomonas, Exiguo bacterium, Acinetobacter bacillaceae, Enterobacteriaceae and Prevotella were the dominant genus (top 10) of bacteria. In case of fungi, xylariales (49%), Hypocreales (19%), Coperinopsis (9%), Alternaria (8%), Fusarium (6%), Biopolaris, Epicoccum, Pleosporaceae, Cladosporium and Nectriaceae were dominant. Antibiotics like, Azithromycin and cefixime were tested on the most dominant bacillus showed resistance on higher concentration of cefixime and lower concentration of azithromycin. Population-based health survey in WWTP nearby areas (50-150 m periphery) found several types of diseases/symptoms including respiratory problem, skin rash/irritation, change in smell and taste, eye irritation within the resident population and workers.
Molecular Insights into Microbial Transformation of Bioaerosol-Derived Dissolved Organic Matter Discharged from Wastewater Treatment Plant

Guodong Zhang,Mingxuan Lou,Jiamin Xu,Yutong Li,Jian Zhou,He Guo,Guangzhou Qu,Tiecheng Wang,Hanzhong Jia,Lingyan Zhu

DOI: https://doi.org/10.1016/j.envint.2023.108404

IF: 11.8

2024-01-01

Environment International

Abstract:Wastewater treatment plants (WWTP) are important sources of aerosol-derived dissolved organic matter (ADOM) which may threaten human health via the respiratory system. In this study, aerosols were sampled from a typical WWTP to explore the chemical molecular diversity, molecular ecological network, and potential toxicities of the ADOM in the aerosols. The high fluorescence index (>1.9) and biological index (0.66-1.17) indicated the strong autogenous microbial source characteristics of the ADOM in the WWTP. DOM and microbes in the wastewater were aerosolized due to strong agitation and bubbling in the treatment processes, and contributed to 74 % and 75 %, respectively, of the ADOM and microbes in the aerosols. The ADOM was mainly composed of CHO and CHOS accounting for 35 % and 29 % of the total number of molecules, respectively, with lignin-like (69 %) as the major constituent. 49 % of the ADOM transformations were thermodynamically limited, and intragroup transformations were easier than intergroup transformations. Bacteria in the aerosols involved in ADOM transformations exhibited both cooperative and divergent behaviors and tended to transform carbohydrate-like and amino sugar/protein-like into recalcitrant lignin-like. The microbial compositions were affected by atmosphere temperature and humidity indirectly by modulating the properties of ADOM. Tannin-like, lignin-like, and unsaturated hydrocarbon-like molecules in the ADOM were primary toxicity contributors, facilitating the expression of inflammatory factors IL-beta (2.2-5.4 folds), TNF-alpha (3.5-7.0 folds), and IL-6 (3.5-11.2 folds), respectively.
Detection and characterization of bioaerosol emissions from wastewater treatment plants: Challenges and opportunities

Jianghan Tian,Cheng Yan,Sonia Garcia Alcega,Francis Hassard,Sean Tyrrel,Frederic Coulon,Zaheer Ahmad Nasir

DOI: https://doi.org/10.3389/fmicb.2022.958514

IF: 5.2

2022-11-10

Frontiers in Microbiology

Abstract:Rapid population growth and urbanization process have led to increasing demand for wastewater treatment capacity resulting in a non-negligible increase of wastewater treatment plants (WWTPs) in several cities around the world. Bioaerosol emissions from WWTPs may pose adverse health risks to the sewage workers and nearby residents, which raises increasing public health concerns. However, there are still significant knowledge gaps on the interplay between process-based bioaerosol characteristics and exposures and the quantification of health risk which limit our ability to design effective risk assessment and management strategies. This review provides a critical overview of the existing knowledge of bioaerosol emissions from WWTPs including their nature, magnitude and size distribution, and highlights the shortcoming associated with existing sampling and analysis methods. The recent advancements made for rapid detection of bioaerosols are then discussed, especially the emerging real time detection methods to highlight the directions for future research needs to advance the knowledge on bioaerosol emissions from WWTPs.

microbiology
Diffusion simulation, health risks, ozone and secondary organic aerosol formation potential of gaseous pollutants from rural comprehensive waste treatment plant

Jiawei Ma,Zexiang Chen,Jun Wang,Ying Wang,Lin Li

DOI: https://doi.org/10.1016/j.chemosphere.2021.131857

IF: 8.8

2022-01-01

Chemosphere

Abstract:Comprehensive waste treatment plants (CWTPs) are significant sources of gaseous pollutants such as odors, volatile organic compounds (VOCs) and nitrogen oxides (NOx), polluting the environment and endangering human health. This study conducted on-site investigations on gaseous pollutants emissions from different areas of a CWTP. A total of 10 pollutants were identified of which ammonia (11.32 mg/m³ in average) was the main odorous substance, and benzene (19.51 mg/m³ in average) and toluene (42.07 mg/m³ in average) were the main VOCs. The feeding workshop (FW) was considered the main source of gaseous pollutants. The Gaussian plume model demonstrated that the pollution became more serious after spreading in the southeast downwind direction. Occupational exposure risks of on-site workers were mainly attributed to hydrogen sulfide, ammonia, benzene, and toluene, as their hazard index (HI) and lifetime cancer risk (CR) exceeded the recommended occupational safety limits. The gaseous pollutants diffused from CWTP may still pose a potential health risk to residents within a range of up to 7.5 km. The emulation and quantification of ozone formation potential by methods of Propyl-Equiv and MIR demonstrated that the contribution rate of toluene presented in each stage of CWTP exceed 80 %. Toluene was also the largest contributor to secondary organic aerosol with the contribution rate reached 56.34-85.14 %, followed by benzene (14.72-38.52 %). This research provides a basis for the reduction and control of gaseous pollutants in the treatment and disposal of rural domestic waste.

environmental sciences
Nitrogen-containing malodorous gas pollutants emission characteristics and health risk assessment from an A/O wastewater treatment plant

Yufan Dong,Linlin Ma,Yi Peng,Zhanhong Hu,Zongze Xu,Xiancong Jiang,Rong Cheng,Haolin Chen,Qing Yang

DOI: https://doi.org/10.1016/j.jwpe.2023.103961

IF: 7

2023-08-01

Journal of Water Process Engineering

Abstract:Unpleasant odorous emitted from wastewater treatment plants (WWTPs) have been of great concern for many years, especially among local communities with high population density. Knowledge about characteristics of odorous gas release from WWTP can assist in developing gas pollution reduction technologies. This study investigated the emission and variation of NH3 and organic amines (CH3NH2, C2H6NH, and C3H9N) at the water-air interface and concentrations of ambient air exposure from different treatment units in a wastewater treatment plant in North China, which uses the anaerobic/oxic (A/O) treatment process. Results demonstrated that NH3 and C2H6NH emission fluxes had followed a descending order of aeration treatment units > non aeration treatment units. NH3 and C2H6NH achieved the highest release concentration throughout the whole wastewater treatment process, where 0.0023 g of NH3 and 0.0018 g of C2H6NH were emitted during the treatment of 1 m3 wastewater, while CH3NH2 and C3H9N had never been detected. The emission of NH3 and C2H6NH from biological aeration tanks account for 98 % and 95 % of the total discharge of wastewater treatment plant, respectively. The odor pollution of NH3 and C2H6NH in the ambient air of different treatment units of WWTP was the most serious in summer. At the sensory level, NH3 dominated the malodorous effect and its exposure concentration posed a certain non carcinogenic risk to workers in wastewater treatment plant.

engineering, chemical, environmental,water resources
CONSENSUS CONFERENCES

M. Oliver,J. Fanu

DOI: https://doi.org/10.1016/S0140-6736(85)92526-7

IF: 202.731

1985-08-17

The Lancet

Abstract:
Transport and risk of airborne pathogenic microorganisms in the process of decentralized sewage discharge and treatment

Yunping Han,Xuezheng Yu,Yingnan Cao,Jianguo Liu,Ying Wang,Zipeng Liu,Chenlei Lyu,Yilin Li,Xu Jin,Yuxiang Zhang,Yu Zhang

DOI: https://doi.org/10.1016/j.watres.2024.121646

IF: 12.8

2024-04-26

Water Research

Abstract:Sewage treatment processes are a critical anthropogenic source of bioaerosols and may present significant health risks to plant workers. Compared with the specialization and scale of urban sewage treatment, many decentralized treatment models are flexible and extensive. These treatment facilities are usually close to residential areas owing to the pipe network layout and other restrictions. Bioaerosols generated by these facilities may present a serious and widespread occupational and non-occupational exposure risk to nearby residents, particularly the elderly and children. An understanding of the characteristics and exposure risks of bioaerosols produced during decentralized sewage treatment is lacking. We compared bioaerosol emission characteristics and potential exposure risks under four decentralized sewage discharge methods and treatment models: small container collection (SCC), open-channel discharge (OCD), single household/combined treatment (SHCT), and centralized treatment (CT) in northwest China. The OCD mode had the highest bioaerosol production, whereas the CT mode had the lowest. The OCD model contained the most pathogenic bacterial species, up to 43 species, including Sphingomonas, Pseudomonas, Cladosporium, and Alternaria . Risk assessments indicated bioaerosol exposure was lower in the models with sewage treatment (SHCT and CT) than in those without (SCC and OCD). Different populations exhibited large variations in potential risks owing to differences in time spent indoors and outdoors. The highest risk was observed in males exposed to the SCC model. This study provides a theoretical basis and theories for the future joint prevention and control of the bioaerosol exposure risk from decentralized sewage treatment.

environmental sciences,engineering, environmental,water resources
The changing pattern of bioaerosol characteristics, source and risk under diversity brush aerator speed

Yan Li,Liying Yang,Huiling Song,Yue Ba,Lin Li,Qing Hong,Yanjie Wang

DOI: https://doi.org/10.1016/j.ecoenv.2022.113478

IF: 7.129

2022-05-01

Ecotoxicology and Environmental Safety

Abstract:Bioaerosols containing pathogens released from wastewater treatment plants (WWTP) may pose potential health risks to workers on-site and residents downwind. In this study, sampling points were set up in the wastewater treatment facility to investigate the generation pattern of bioaerosols in the aeration tank section. High-throughput sequencing was utilized to assay the intestinal bacteria population, while the health risks associated with airborne bacteria were estimated based on average daily dose rates. The contribution of wastewater to bioaerosols was evaluated using the traceability analysis. As the rotational speed increased from 200 rpm to 800 rpm, the concentration of culturable bacteria increased from 397 CFU/m3 to 1611 CFU/m3, the proportion of bacteria attached to particles with an aerodynamic diameter larger than 4.7 µm increased from 30.41% to 48.44%, and the Shannon index of air samples increased from 1.032485 to 1.282065. Microbial composition, sources, and health risks of bioaerosols also changed as the rotational speed increased. The results showed that the predominant bacteria in the air at 200 rpm were Bacillus (78.78%), Paenibacillus (11.77%) and Lysinibacillus (1.40%). When the rotating speed reached 800 rpm, the dominant bacteria became Bacillus (55.50%), Acinetobacter (31.01%), and Paenarthrobacter (13.17%). The contribution of the wastewater to bioaerosols increased from 46.49% to 65.10%, in which surface water was the main source of bioaerosols (34.64% on average). Although the contribution of bottom water was lower than that of surface water, its contribution increased more, from 15.36% to 29.31%. The health risk of bioaerosols was 1.28 × 10-2 on average, which increased with the increase of rotational speed. At the same exposure concentration, children (2.31 × 10-2) have a higher exposure risk than adults (7.67 × 10-3). This study is aimed at exploring the variation law of bioaerosols discharged from WWTP with oxidation ditch process and providing preliminary data for reducing its risk.

environmental sciences,toxicology
Bioaerosolization behaviour of potential pathogenic microorganisms from wastewater treatment plants: Occurrence profile, social function and health risks

Nana Zang,Hongyu Tian,Xinyue Kang,Jianwei Liu

DOI: https://doi.org/10.1016/j.scitotenv.2024.171300

IF: 9.8

2024-03-10

The Science of The Total Environment

Abstract:Wastewater treatment plants (WWTPs) are the leading sources of potential pathogenic bioaerosol that cause non-negligible health risks. However, bioaerosolization behaviour of potential pathogenic microorganisms (PPMs) migrating from wastewater to the atmosphere is still unclear. This study investigated the occurrence profile of PPMs in wastewater, sludge and bioaerosol, then analyzed bioaerosolization level, impact factors and social function. Staphylococcus aureus was selected as the target due to its pathogenicity, and the health risks of workers, engineers and researchers wearing various masks (N90, N95 and medical masks) were evaluated. The results showed that there were 38 and 64 PPMs in bioaerosol from plant A and B. Streptomyces in plant A (average bioaerosolization index, BI= 237.71) and Acinetobacter in plant B (average BI = 505.88) were more likely to migrate from wastewater to the atmosphere forming bioaerosol. Environmental factors (relative humidity, wind speed and temperature) affected both BI and microbial species of PPMs in different ways. PPMs related to fermentation, aerobic chemoheterotrophy, and chemoheterotrophy are the most abundant. Meanwhile microbial networks from plants A and B showed that PPMs were well-connected. Emission level of Staphylococcus aureus bioaerosol can reach 980 ± 309.19 CFU/m 3 in plant A and 715.55 ± 44.17 CFU/m 3 in plant B. For three exposure population, disease burden (DB) and annual probability infection (Py) of Staphylococcus aureus bioaerosol in two plants were both higher than the U.S.EPA benchmark (10 −4 DALYs pppy). All three masks (N90,N95 and medical masks) can decrease Py and DB by at least one order of magnitude. This study illustrated the bioaerosolization behaviour of PPMs comprehensively, which provides a scientific basis for exposure risk prevention and control.

environmental sciences
[Characteristics of Bioaerosols Emitted from WWTP with SBR Treatment Process]

Kai-Xiong Yang,Hong-Xun Hou,Ying-Zhe Wang,Hao-Ran Shi,Guang-Su Xu,Yun-Ping Han,Jun-Xin Liu,Lin Li

DOI: https://doi.org/10.13227/j.hjkx.201803161

2018-11-08

Abstract:Sampling sites were located in a wastewater treatment plant (WWTP) with a sequencing batch reactor activated sludge process to investigate the characteristics of bioaerosol emissions. The results indicated that bioaerosols were detected from each treatment section of the WWTP, and concentrations of bioaerosols were in the range of 82-1525 CFU·m-3. The coarse screen, aeration tank, and sludge dewatering house were the main sources of bioaerosols. The dominant species in each treatment section was Cyanobacteria, and the other main bacterial taxa were Aeromonas, Peptostreptococcaceae, Moraxellaceae, Chroococcidiopsis, Sphingomonas, Arcobacter, and Acinetobacter. Among the identified bacterial genera, Aeromonas, Arcobacter, Acinetobacter, and Sphingomonas were potential pathogens. Bioaerosol concentration and abundance decreased along the vertical and horizontal directions. Appropriate temperature and relative humidity benefited the survival of bioaerosols in the air (P<0.01), whereas a negative relationship between bioaerosol concentration and wind speed was observed (P<0.05). Although exposure risks caused by bioaerosols were negligible in this study, the accumulation of bioaerosols would increase potential health risks. The bioreactor for odor treatment could effectively reduce bioaerosol emissions.

Electrodialytic remediation of CCA-treated waste wood in a 2 m(3) pilot plant.

Bioaerosols emission and exposure risk of a wastewater treatment plant with A2O treatment process

The generation characteristics, pattern, and exposure risk of bioaerosol emitted in an A2O process wastewater treatment plant

Cultivation-dependent and Cultivation-Independent Investigation of O-methylated Pollutant-Producing Bacteria in Three Drinking Water Treatment Plants

Linking aerosol characteristics of size distributions, core potential pathogens and toxic metal(loid)s to wastewater treatment process

Bioaerosol-related studies in wastewater treatment plant with anaerobic-anoxic-oxic processes: Characterization, source analysis, control measures

Editorial: Will the real neutrophil please stand up?

Bioaerosol in a typical municipal wastewater treatment plant: concentration, size distribution, and health risk assessment

Quantitative microbial risk assessment with nasal/oral breathing pattern for S. aureus bioaerosol emission from aeration tanks and residual sludge storage yard in a wastewater treatment plant

Bioaerosols in deodorization covers of wastewater treatment plants: Emission characteristics and health risks

Bioaerosols emission characteristics from wastewater treatment aeration tanks and associated health risk exposure assessment during autumn and winter

Bioaerosol emissions from wastewater treatment process at urban environment and potential health impacts

Molecular Insights into Microbial Transformation of Bioaerosol-Derived Dissolved Organic Matter Discharged from Wastewater Treatment Plant

Detection and characterization of bioaerosol emissions from wastewater treatment plants: Challenges and opportunities

Diffusion simulation, health risks, ozone and secondary organic aerosol formation potential of gaseous pollutants from rural comprehensive waste treatment plant

Nitrogen-containing malodorous gas pollutants emission characteristics and health risk assessment from an A/O wastewater treatment plant

CONSENSUS CONFERENCES

Transport and risk of airborne pathogenic microorganisms in the process of decentralized sewage discharge and treatment

The changing pattern of bioaerosol characteristics, source and risk under diversity brush aerator speed

Bioaerosolization behaviour of potential pathogenic microorganisms from wastewater treatment plants: Occurrence profile, social function and health risks

[Characteristics of Bioaerosols Emitted from WWTP with SBR Treatment Process]