Abstract:During the operation progress of solid oxide fuel cell (SOFC), the performance and endurance are two major concerns significantly affected by gas flowing, charge transport, and chemical reaction. This paper presents a thorough research on the key parameters related to syngas and charge transport in the SOFC to reveal the intrinsic influence mechanism, including electro conductibility, gas mixture concentration, CH 4 component ratio, temperature, and anode thickness, which is instrumental in improving the operational efficiency and applicability of SOFC. Firstly, the theoretical models of charge transport and multi-component mass transfer are established, respectively, and the two are coupled using the reaction rate calculation method. Then, employing an innovative combination of the representative elementary volume (REV) scale lattice Boltzmann method (LBM) and the finite-difference LBM, the potential and multi-component gases distributions are simulated to calculate the evaluated indicators, namely activation and concentration overpotential. Finally, considering various operational conditions, the simulation experiments are conducted to investigate the parametric effect on the performance of SOFC fueled by syngas. The results demonstrate that compared to the direct reforming way, the external syngas with lower CH 4 component ratio is more favorable to the SOFC and the optimal ratio should be controlled within 0.2. The higher concentration of gas mixture and lower anode thickness both contribute to weakening the effect of concentration polarization. Especially, the performance of SOFC is improved when the concentration is 15 mol‧m −3 and the anode thickness is below 1.05 mm. With the increment of conductivity and operating temperature, the consumption of H 2 gradually increases, enhancing the efficiency of reaction gas and reducing the economic cost. And the optimal operation temperature of SOFC is about 1073 K. Moreover, the anode thickness is a trade-off between the electrochemical reaction conditions of anode and cathode, as its variation affects both of them.

Numerical study on the impact of carbon deposition on methane/steam mass transport in solid oxide fuel cell porous anode using lattice Boltzmann modeling

Lattice Boltzmann Modeling of Carbon Deposition in Porous Anode of a Solid Oxide Fuel Cell with Internal Reforming

Impact of Carbon Deposition on Diffusion Parameters in Porous Anodes of Solid Oxide Fuel Cells Using the Lattice Boltzmann Method

Numerical simulation of carbon deposition in solid oxide fuel cells

Multi-Physics Modeling of Solid Oxide Fuel Cell Fueled by Methane and Analysis of Carbon Deposition

Simulation study of anode gas and potential distribution of fuel cell based on lattice Boltzmann method

Numerical Study on Carbon Deposition of SOFC with Unsteady State Variation of Porosity

Numerical Investigation of Coupled Mass Transport and Electrochemical Reactions in Porous Sofc Anode Microstructure

Parametric analysis of solid oxide fuel cell fueled by syngas based on lattice Boltzmann method

Parameter Study of Transient Carbon Deposition Effect on the Performance of a Planar Solid Oxide Fuel Cell

PORE-SCALE INVESTIGATION OF MASS TRANSFER IN SOLID OXIDE FUEL CELL ANODE

Control of carbon deposition over methane-fueled SOFCs through tuning the O/C ratio at the anode/electrolyte interface

In-situ Analysis of Anode Atmosphere in a Flat-Tube Solid Oxide Fuel Cell Operated with Dry Reforming of Methane

Degradation mechanisms and mitigation strategies of direct methane solid oxide fuel cells

Pore Scale Investigation of Gaseous Mixture Flow in Porous Anode of Solid Oxide Fuel Cell

Multi-Physics Modeling Assisted Design of Non-Coking Anode for Planar Solid Oxide Fuel Cell Fueled by Low Steam Methane

Studies on the Carbon Reactions in the Anode of Deposited Carbon Fuel Cells

Electrochemical performance study of solid oxide fuel cell using lattice Boltzmann method

Performance and Effective Kinetic Models of Methane Steam Reforming over an Ni-YSZ Anode of Planar Solid Oxide Fuel Cell

Application and development of the Lattice Boltzmann modeling in pore-scale electrodes of solid oxide fuel cells

Impact of SOFC anode carbon deposition and hydrogen adsorption on the cell performance by molecular simulation