Abstract:Recent advances in additive manufacturing (AM) have enabled the fabrication of functionally graded porous biomaterials (FGPBs) for application as orthopedic implants and bone substitutes. Here, we present a step-wise topological design of FGPB based on diamond unit cells to mimic the structure of the femoral diaphysis. The FGPB was manufactured from Ti-6Al-4V powder using the selective laser melting (SLM) technique. The morphological parameters, permeability and mechanical properties of FGPB samples were measured and compared with those of the biomaterials with uniform porous structures based on the same type of the unit cell. The FGPB exhibited a low density (1.9 g/cm3), a moderate Young's modulus (10.44 GPa), a high yield stress (170.6 MPa), a high maximum stress (201 MPa) and favorable ductility, being superior to the biomaterials with uniform porous structures in comprehensive mechanical properties. In addition, digital image correlation (DIC) and finite element (FE) simulation were used to unravel the mechanisms governing the deformation and yielding behavior of these biomaterials particularly at the strut junctions. Both DIC and FE simulations confirmed that the deformation and yielding of the FGPB occurred largely in the load-bearing layers but not at the interfaces between layers. Defect-coupled FE models based on solid elements provided further insights into the mechanical responses of the FGPB to compressive loads at both macro- and micro-scales. With the defect-coupled representative volume element model for the FGPB, the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The study clearly demonstrated the capabilities of combined experimental and computational methods to resolve the uncertainties of the mechanical behavior of FGPBs, which would open up the possibilities of applying various porosity variation strategies for the design of biomimetic AM porous biomaterials. STATEMENT OF SIGNIFICANCE: Functionally graded bone scaffolds significantly promote the recovery of segmental bone defect. In the present study, we present a step-wise topological design of functionally graded porous biomaterial (FGPB) to mimic the structure of the femoral diaphysis. The Ti-6Al-4V FGPB exhibited a superior combination of low density, moderate Young's modulus, high yield stress and maximum stress as well as favorable ductility. The biomechanical performance of FGPB was studied in both macro and micro perspectives. The defect-coupled model revealed the significant yielding in the load-bearing parts and the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The superiority of combined experimental and computational methods has been confirmed.

Biomechanical response of a novel intervertebral disc prosthesis using functionally graded polymers: A finite element study

Crystallinity dependency of the time-dependent mechanical response of polyethylene: application in total disc replacement

Fiber‐Dependent 3D Anisotropic Stiffness‐Tunable Biomimetic Intervertebral Disc via Multi‐Material Additive Manufacturing

Finite element analysis of optimized novel additively manufactured non-articulating prostheses for cervical total disc replacement

On the suitability of additively manufactured gyroid structures and their potential use as intervertebral disk replacement - a feasibility study

Toward a mechanically biocompatible intervertebral disc: Engineering of combined biomimetic annulus fibrosus and nucleus pulposus analogs.

Three-Dimensional-Printed Flexible Scaffolds Have Tunable Biomimetic Mechanical Properties for Intervertebral Disc Tissue Engineering

Structural Modification and Biomechanical Analysis of Lumbar Disc Prosthesis: A Finite Element Study

[Biomechanical Analysis of Different ProDisc-C Arthroplasty Design Parameters after Implanted: a Numerical Sensitivity Study Based on Finite Element Method].

Pilot Biomechanical Design of Biomaterials for Artificial Nucleus Prosthesis Using 3d Finite-Element Modeling

BIOMECHANICAL ANALYSIS OF DIFFERENT PRODISC-C ARTHROPLASTY DESIGNS AFTER IMPLANTATION: A NUMERICAL SENSITIVITY STUDY

Biomechanical Evaluation of Cervical Disc Replacement with a Novel Prosthesis Based on the Physiological Curvature of Endplate

3D-Printed Auxetic-Structured Intervertebral Disc Implant for Potential Treatment of Lumbar Herniated Disc

Regional variations of mechanical responses of IVD to 7 different motions: An in vivo study combined with FEA and DFIS

Developing a novel functional disc emulator to investigate the nucleus pulposus replacement

A new cervical artificial disc prosthesis based on physiological curvature of end plate: a finite element analysis.

Materials and design concepts for an intervertebral disc spacer. II. Multidurometer composite design

Biomechanical Analysis of A Novel Prosthesis Based on the Physiological Curvature of Endplate for Cervical Disc Replacement

Bioinspired Intervertebral Disc with Multidirectional Stiffness Prepared via Multimaterial Additive Manufacturing

Topological design, permeability and mechanical behavior of additively manufactured functionally graded porous metallic biomaterials

Validation and application of an intervertebral disc finite element model utilizing independently constructed tissue-level constitutive formulations that are nonlinear, anisotropic, and time-dependent