Abstract:Background: Anterior cervical discectomy and fusion (ACDF) sacrifices segmental mobility, which can lead to the acceleration of adjacent segment degeneration. The challenge has promoted cervical artificial disc replacement (CADR) as a substitute for ACDF. However, CADR has revealed a series of new issues that are not found in ACDF, such as hypermobility, subsidence, and wear phenomenon. This study designed a cervical subtotal discectomy prosthesis (CSDP) consisting of a cervical disc prosthesis structure (CDP structure), cervical vertebra fixation structure (CVF structure), link structure, and locking screw, aiming to facilitate motion control and reduce subsidence. The aim of this study was to assess the biomechanics of the CSDP using finite element (FE) analysis, friction-wear test, and non-human primates implantation study. Study Design: For the FE analysis, based on an intact FE C 2 -C 7 spinal model, a CSDP was implanted at C 5 -C 6 to establish the CSDP FE model and compare it with the Prestige LP prosthesis (Medtronic Sofamor Danek, Minneapolis, MN, United States). The range of motion (ROM), bone-implant interface stress, and facet joint force were calculated under flexion extension, lateral bending, and axial rotation. In addition, CSDP was elevated 1 mm to mimic an improper implantation technique to analyze the biomechanics of CSDP errors in the FE model. Moreover, the friction-wear test was conducted in vitro to research CSDP durability and observe surface wear morphology and total wear volume. Finally, the CSDP was implanted into non-human primates, and its properties were evaluated and verified by radiology. Results: In the FE analysis, the ROM of the CSDP FE model was close to that of the intact FE model in the operative and adjacent segments. In the operative segment, the CSDP error FE model increased ROM in flexion extension, lateral bending, and axial rotation. The maximum stress in the CSDP FE model was similar to that of the intact FE model and was located in the peripheral cortical bone region. The facet joint force changes were minimal in extension, lateral bending, and axial rotation loads in CSDP. In the friction-wear test, after the 150-W movement simulation, both the CVF-link-junction and the CDP-link-junction had slight wear. In the CSDP non-human primate implantation study, no subsidence, dislocation, or loosening was observed. Conclusion: In the FE analysis, the biomechanical parameters of the CSDP FE model were relatively close to those of the intact FE model when compared with the Prestige LP FE model. In terms of CSDP error FE models, we demonstrated that the implantation position influences CSDP performance, such as ROM, bone-implant interface stress, and facet joint force. In addition, we performed a friction-wear test on the CSDP to prove its durability. Finally, CSDP studies with non-human primates have shown that the CSDP is effective.

Biomechanical analysis of single and multi-level artificial disc replacement (ADR) in cervical spine using multi-scale loadings: A finite element study

BIOMECHANICAL ANALYSIS OF DIFFERENT PRODISC-C ARTHROPLASTY DESIGNS AFTER IMPLANTATION: A NUMERICAL SENSITIVITY STUDY

External and internal responses of cervical disc arthroplasty and anterior cervical discectomy and fusion: A finite element modeling study

Biomechanical Analysis of A Novel Prosthesis Based on the Physiological Curvature of Endplate for Cervical Disc Replacement

Biomechanical Analysis of Two-level Cervical Disc Replacement With a Stand-alone U-shaped Disc Implant.

A new cervical artificial disc prosthesis based on physiological curvature of end plate: a finite element analysis.

Biomechanical properties of a novel cervical spine implant with elastic deformation: a cadaveric study

Biomechanical Analysis of Two-Level Novel Cage-Type Implant for Anterior Cervical Discectomy and Fusion: A Finite Element Analysis

Biomechanical Analysis of Cervical Artificial Disc Replacement Using Cervical Subtotal Discectomy Prosthesis

Biomechanics of Artificial Disc Replacements Adjacent to a 2-Level Fusion in 4-Level Hybrid Constructs: an in Vitro Investigation

Biomechanics of Hybrid Anterior Cervical Fusion and Artificial Disc Replacement in 3-Level Constructs: an in Vitro Investigation.

Biomechanical Analysis of Hybrid Artificial Discs or Zero-Profile Devices for Treating 1-Level Adjacent Segment Degeneration in ACDF Revision Surgery

Biomechanical Evaluation of Cervical Disc Replacement with a Novel Prosthesis Based on the Physiological Curvature of Endplate

3D printed anatomical bionic artificial cervical disc replacement for single-level cervical spondylosis: a cohort study

A comparative finite element analysis of artificial intervertebral disc replacement and pedicle screw fixation of the lumbar spine

Biomechanical Comparison of Different Surgical Strategies for Skip-level Cervical Degenerative Disc Disease: A Finite Element Study

Bio-Mechanical behaviour of artificial intervertebral disc in lumbar spine

Comparison of Multilevel Cervical Disc Replacement and Multilevel Anterior Discectomy and Fusion: A Systematic Review of Biomechanical and Clinical Evidence.

Three-dimensional finite element analysis on artificial cervical disc replacement for activities of lower cervical spine

A comparative study of the effect of facet tropism on the index-level kinematics and biomechanics after artificial cervical disc replacement (ACDR) with Prestige LP, Prodisc-C vivo, and Mobi-C: a finite element study

[Biomechanical Analysis of Different ProDisc-C Arthroplasty Design Parameters after Implanted: a Numerical Sensitivity Study Based on Finite Element Method].