Abstract:Journal of Reinforced Plastics and Composites, Ahead of Print. The fiber/matrix interface is a critical item that affects Fiber Reinforced Polymer (FRP) composites mechanical performance due to its control of the load transfer mechanism. Partially bonded interfaces have been shown to affect the failure mode of FRP composites. This article examines the significance of manipulating the fiber/matrix interfacial bond in 3D printed FRP composites on the mechanical performance of multilayer 3D printed FRP composites. Three designs are investigated with different fiber stacking sequences, fiber orientation, and interfacial bond configurations. The designs have a low coefficient of variation in load fractions between layers to enable a gradual load transfer and progressive failure. Utilizing 3D printer chamber temperature changes, a composite with a controlled bond configuration is achieved using thermal blocks. It was observed that the controlled bond configurations resulted in promoting progressive failure and increased the strain at failure of 3D printed FRP composites. The observations of direct tension tests were supported with interlayer shear strength and interfacial adhesion tests which explained the weakened load transfer in the thermal block configurations. Using the interface manipulation strategy with thermal blocks in 3D printed specimens, a 25% lower interlayer shear strength and a 65% lower interfacial adhesion was achieved compared with un-modified interfaces. These changes attribute to the altered load transfer mechanism in 3D printed glass fiber reinforced composites and high strain to failure of up to 5% using high strength high stiffness fiber orientations. This work does not incorporate any new materials into the thermoplastic-fiber 3D printed structure which has been the strategy of past work to modify mechanical performance. Alternatively, a unique approach by using chamber and print bed temperature characteristics to modify the interfacial bond has been adopted that has shown to promote progressive failures and improve ductility in FRP composites. This study furthers the development of ductile designs in FRP composites with 3D printing technology in aerospace, wind, infrastructure, and automobile applications.

Thin-ply thermoplastic composites: From weak to robust transverse performance through microstructural and morphological tuning

Short fibre/unidirectional hybrid thermoplastic composites: Experimental characterisation and digital analysis

Inherent relationship between process parameters, crystallization and mechanical properties of continuous carbon fiber reinforced peek composites

The use of discontinuous PEEK/carbon fiber thermoplastic moulding compounds for thick-section componentry

High Performance Ductile and Pseudo-ductile Polymer Matrix Composites: a Review

Optimization of geometrical factors for enhanced performance of carbon fiber reinforced polymer cores under transverse loading

Structure Design on Thermoplastic Composites Considering Forming Effects

Evolution of Manufacturing Defects of 3D-Printed Thermoplastic Composites with Processing Parameters: A Micro-CT Analysis

Rheology and Processing of High-Strength Liquid Crystal Polymer Reinforced Thermoplastic Composite Materials

Experimental characterization and stochastic models for time-dependent rupture of thin-ply composite laminates

Additive manufacturing and microstructure effects on thermal and mechanical properties of ply-hybrid carbon and glass fiber composites

Behaviour of Rectangular Hollow Thin Ply Carbon Thermoset and Thermoplastic Composite Tubes Subjected to Bending

The effect of microstructure on the tensile and impact behaviour of short-glass fibre-reinforced polyamide 6.6 as assessed by micro-computed tomography

A Modeling Framework for the Thermoforming of Carbon Fiber Reinforced Thermoplastic Composites

Flexural behaviours and heterogeneous interface fracture in overmoulded multi-material thermoplastic composites

Analysis of impact response and damage evolution in multi‐scale of novel 3D carbon fiber‐reinforced polyetheretherketone composites

CFRP Thin-Ply Fibre Metal Laminates: Influences of Ply Thickness and Metal Layers on Open Hole Tension and Compression Properties

Ultrafine‐Grained Laminated Metal Composites: A New Material Class for Tailoring Cyclically Stressed Components

Effect of fiber type and thickness on mechanical behavior of thermoplastic composite plates reinforced with fabric plies

Manipulating interfacial bond for controlling load transfer in 3D printed fiber reinforced polymer composites

Experimental and theoretical investigation on tensile properties and fracture behavior of carbon fiber composite laminates with varied ply thickness