Abstract:Journal of Reinforced Plastics and Composites, Ahead of Print. The fiber/matrix interface is a critical item that affects Fiber Reinforced Polymer (FRP) composites mechanical performance due to its control of the load transfer mechanism. Partially bonded interfaces have been shown to affect the failure mode of FRP composites. This article examines the significance of manipulating the fiber/matrix interfacial bond in 3D printed FRP composites on the mechanical performance of multilayer 3D printed FRP composites. Three designs are investigated with different fiber stacking sequences, fiber orientation, and interfacial bond configurations. The designs have a low coefficient of variation in load fractions between layers to enable a gradual load transfer and progressive failure. Utilizing 3D printer chamber temperature changes, a composite with a controlled bond configuration is achieved using thermal blocks. It was observed that the controlled bond configurations resulted in promoting progressive failure and increased the strain at failure of 3D printed FRP composites. The observations of direct tension tests were supported with interlayer shear strength and interfacial adhesion tests which explained the weakened load transfer in the thermal block configurations. Using the interface manipulation strategy with thermal blocks in 3D printed specimens, a 25% lower interlayer shear strength and a 65% lower interfacial adhesion was achieved compared with un-modified interfaces. These changes attribute to the altered load transfer mechanism in 3D printed glass fiber reinforced composites and high strain to failure of up to 5% using high strength high stiffness fiber orientations. This work does not incorporate any new materials into the thermoplastic-fiber 3D printed structure which has been the strategy of past work to modify mechanical performance. Alternatively, a unique approach by using chamber and print bed temperature characteristics to modify the interfacial bond has been adopted that has shown to promote progressive failures and improve ductility in FRP composites. This study furthers the development of ductile designs in FRP composites with 3D printing technology in aerospace, wind, infrastructure, and automobile applications.

Manipulating interfacial bond for controlling load transfer in 3D printed fiber reinforced polymer composites

Interfacial Bonding During Multi-Material Fused Deposition Modeling (FDM) Process Due to Inter-Molecular Diffusion

Enhancing fiber/matrix interface adhesion in polymer composites: Mechanical characterization methods and progress in interface modification

Investigation on the mechanical properties of 3D printed hybrid continuous fiber-filled composite considering influence of interfaces

Improved interlayer performance of short carbon fiber reinforced composites with bio-inspired structured interfaces

Interfacial behaviors of continuous carbon fiber reinforced polymers manufactured by fused filament fabrication: A review and prospect

Interfacial performance and build orientation of 3D‐printed poly(ether‐ketone‐ketone) reinforced by continuous carbon fiber

On the Effects of Process Parameters and Optimization of Interlaminate Bond Strength in 3D Printed ABS/CF-PLA Composite

Investigating gradient temperature control for enhanced interfacial bonding behavior in material extrusion 3D printing continuous fiber reinforced polymer composites

Atomistic Modeling of the Effect of Temperature on Interfacial Properties of 3D-Printed Continuous Carbon Fiber-Reinforced Polyamide 6 Composite: From Processing to Loading

Processing, mechanical characterization, and micrography of 3D-printed short carbon fiber reinforced polycarbonate polymer matrix composite material

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

Investigation of Fiber–Matrix Interface Strength via Single-Fiber Pull-Out Test in 3D-Printed Thermoset Composites: A Simplified Methodology

Enhancing the interfacial bonding strength between 3D-printed aluminium substrates and carbon fibre–reinforced polymers

Fused-Deposition Modeling 3D Printing of Short-Cut Carbon-Fiber-Reinforced PA6 Composites for Strengthening, Toughening, and Light Weighting

3D printing for continuous fiber reinforced thermoplastic composites: mechanism and performance

Preparation and Evaluation of the Tensile Characteristics of Carbon Fiber Rod Reinforced 3D Printed Thermoplastic Composites

The role of the fiber–matrix interface in the tensile properties of short fiber–reinforced 3D‐printed polylactic acid composites

Enhancing interlaminar adhesion in multi-material 3D printing: A study of conductive PLA and TPU interfaces through fused filament fabrication

Bending and shear improvements in 3D-printed core sandwich composites through modification of resin uptake in the skin/core interphase region

Improvement of Heat Treatment Process on Mechanical Properties of FDM 3D-Printed Short- and Continuous-Fiber-Reinforced PEEK Composites