Abstract:This article, written by JPT Technology Editor Chris Carpenter, contains highlights of paper SPE 201609, “Cellulose Nanocrystal Switchable Gel for Improving CO2 Sweep Efficiency in Enhanced Oil Recovery and Gas Storage,” by Ali Telmadarreie, University of Calgary and Cnergreen; Christopher Johnsen, University of Calgary; and Steven Bryant, University of Calgary and Cnergreen, prepared for the 2020 SPE Annual Technical Conference and Exhibition, originally scheduled to be held in Denver, 5–7 October. The paper has not been peer reviewed. The entanglement of biopolymers is a well-known phenomenon that, when controlled, can result in a smart fluid with strong gelation properties. The authors write that, when a suitable salt is incorporated into the cellulose nanocrystal (CNC), the fluids undergo gelation upon contact with bulk-phase carbon dioxide (CO2) but remain a flowing liquid otherwise. In this study, this composition-selective trigger was applied to improve sweep efficiency in CO2 enhanced oil recovery (EOR) and sequestration. Introduction Hydrogels are hydrophilic structures that swell when hydrated and have various applications in industry. Hydrogels are of interest in EOR because of their ability to respond to stimuli such as pH, temperature, light, and ionic strength. CNCs are nanoparticles derived from cellulose, one of the more sustainable natural resources available. CNC hydrogels could have specific applications as a solution to media het-erogeneity and poor gas-sweep efficiency. The hydrogels can be tuned to set over time, allowing the intentional placement of gels into already-swept areas of a reservoir. CNC hydrogels are unique in that they can be formed when contacted with CO2 and broken by the application of nitrogen (N2) gas. The pH of the solution will be increased as the nitrogen partitions across the gel, reversing the CO2 reaction. This gives the gel-forming solution the added benefit of being transmittable throughout a reservoir. Material and Procedure Spray-dried CNCs with an average length of 100–200 nm and a width of 15 nm were used. Imidazole was used as the salt mixed with water and CNC suspension to create a pH-triggered gel system. CO2 gas and N2 gas were used as received. Mineral oil with a viscosity of approximately 20 cp was used at the oil phase. Solution preparation, and the process for gel strength in bulk testing, are provided in the complete paper. All tests were performed at a pressure of 400 psi and an ambient temperature of 21°C. Two sets of flow experiments were performed. The first included flow in a single sandpack saturated with water to investigate the in-situ gelation and reversibility of the gel. The second set used a dual-sandpack system. The shorter sandpack with higher permeability was saturated with water to create a path of less resistance compared with the longer sandpack with lower permeability saturated with viscous oil. Further details of these experiments are provided in the complete paper.

Tunable gas selectivity of cellulose nanocrystals – Polyethylene glycol composite membranes

Selective CO2 Separation from CO2−N2 Mixtures by Immobilized Carbonate−Glycerol Membranes

Nanostructured Poly(l-Lactic Acid)-Poly(ethylene Glycol)-Poly(l-lactic Acid) Triblock Copolymers and Their CO2/O-2 Permselectivity

Gas Permeation Performance of Cellulose Hollow Fiber Membranes Made from the Cellulose/n‐methylmorpholine‐n‐oxide/h2o System

CO2 permeability, diffusivity and solubility in polyethylene glycol-grafted polyionic membranes and their CO2 selectivity relative to methane and nitrogen

Nanocellulose‐Incorporated Composite Membranes of PEO‐Based Rubbery Polymers for Carbon Dioxide Capture

A Comparison of the Effect of Cellulose Nanocrystals (CNCs) and Polyethylene Glycol (PEG) as Additives in Ultrafiltration Membranes (PES-UF): Characterization and Performance

Selective Permeation of CO2 Through a Composite Membrane with a Separation Layer of 2-N,n-dimethyl Aminoethyl Methacrylate and Acrylic Acid Copolymer

Enhancing CO2 Transport Across the PEG/PPG-Based Crosslinked Rubbery Polymer Membranes with a Sterically Bulky Carbazole-Based ROMP Comonomer

Biogas purification by CO2 removal using facilitated transport mechanism of cellulose nanocrystals/polyvinyl alcohol layered hollow fiber membranes

Pebax/Peg Grafted Cnt Hybrid Membranes For Enhanced Co2/N-2 Separation

Effect of temperature and pressure on gas transport in ethyl cellulose membrane

Biogas purification using cellulose nanocrystals/polyvinyl alcohol coated facilitated transport hollow fiber membranes with L‐arginine as CO2 carrier

Reinforcement of single-walled carbon nanotubes on polydimethylsiloxane membranes for CO2, O2, and N2 permeability/selectivity

Morphology and Gas Permselectivity of Blend Membranes of Polyvinylpyridine with Ethylcellulose

Nanostructured membrane material designed for carbon dioxide separation

Polyvinyl alcohol and aminated cellulose nanocrystal membranes with improved interfacial compatibility for environmental applications

Investigation of mixed matrix membranes of graphene and acid‐treated graphene fillers in cellulose acetate and polyetherimide polymers for CO2 separation from biogas

Modification of CO2-selective mixed matrix membranes by a binary composition of poly(ethylene glycol)/NaY zeolite

Suppression of Crystallization in Thin Films of Cellulose Diacetate and Its Effect on CO2/CH4 Separation Properties

Cellulose Nanocrystal Switchable Gel Improves CO2 Sweep Efficiency