Abstract:Cold metal transfer (CMT) technology based on wire-arc manufacturing has attracted wide attention because of its advantages of high manufacturing efficiency, low heat input ( HI ) and near-net-shape. In this study, a CMT-Hastelloy C-276 superalloy surface modification coating by optimizing HI is used to solve the problem of premature failure of key over-flow components of stainless steel in marine engineering. When the HI is increased from 269 J/mm to 358 J/mm, the serious cavitation erosion (CE) damage caused by pore defects and excessive residual tensile stress due to excessive low HI of Hastelloy C-276 coating can be avoid, which is attributed to the effective Orowan strengthening and high proportion of low angle grain bounds (LAGBs: 70.2%). In addition, high contents of Cr, Mo and W elements can promote it's passivation film to maintain excellent self-healing ability during CE to provide continuous and stable protection effect ( R ct = 75.68 kΩ·cm 2 ) in the 3.5 wt% NaCl artificial seawater. Therefore, even after 10 h-CE, it still maintains the highest corrosion resistance from both of the thermodynamic ( E corr = −193.5 ± 3.6 mV) and kinetic perspective ( I corr = 69.3 ± 3.1 μA·cm −2 ) and has the lowest mean depth erosion rates ( MDER , 0.94 ± 0.07 μm/h). However, further increase of HI will cause coarsing of grains (89.6 ± 2.7 μm → 342.8 ± 9.7 μm), excessive precipitation of brittle Mo-rich p phase and excessive dilution of elements from the substrate, resulting in changes in the wear mechanism and deterioration of strength and corrosion resistance. Moreover, the potential of zero charge ( PZC ) measurements and Mott-Schottky ( M-S ) test confirmed the decreasing trend of the repulsive ability to Cl ions ( ΔE = 0.58 V) and the increased ion doping concentration ( N D = 5.94 ± 0.02 × 10 22 cm −3 ) of the weakened n-type passivation films. The optimal combination of wear resistance, corrosion resistance and CE resistance of Hastelloy C-276 coating is obtained by regulating HI , which can lay a theoretical foundation for the related production and application of marine engineering.

Microstructure development and cavitation erosion resistance enhancement of additive manufactured Hastelloy C276 alloy coating on martensitic stainless–steel via directed energy deposition

Microstructure and Mechanical Properties of Interface Between Laser Cladded Hastelloy Coating and Steel Substrate

Microstructures, mechanical properties and corrosion resistance of Hastelloy C22 coating produced by laser cladding

Preparation of CrCoFeNiMn High-Entropy Alloy Coatings Using Gas Atomization and Laser Cladding: An Investigation of Microstructure, Mechanical Properties, and Wear Resistance

Microstructure and mechanical properties of Stellite 6 alloy coating metallurgically bonded to 304 stainless steel by DED-LB technology

Stabilised mechanical properties in Ni-based Hastelloy C276 alloy by additive manufacturing under different heat inputs incorporated with active interlayer temperature control

Nano and micron WC particles reinforced Hastelloy C22 coatings manufactured by directed energy deposition

Correlation between microstructural characteristics and cavitation resistance of Stellite-6 coatings on 17-4 PH stainless steel prepared with supersonic laser deposition and laser cladding

Cavitation erosion/corrosion synergy and wear behaviors of nickel-based alloy coatings on 304 stainless steel prepared by cold metal transfer

An investigation on the effect of heat input to wear behavior and corrosion-cavitation erosion mechanism of Hastelloy C-276 coating by cold metal transfer

Corrosion Behavior of Hastelloy C22 Coating Produced by Laser Cladding in Static and Cavitation Acid Solution

Microstructure and high temperature erosion behavior of laser cladded CoCrFeNiSi high entropy alloy coating

Planification of Amorphous Carbon Coatings Via Periodically Transitional Sp2/sp3 Bonds to Enhance Cavitation Erosion Resistance

Effect of synergistic cavitation erosion-corrosion on cavitation damage of CoCrFeNiMn high entropy alloy layer by laser cladding

Microstructure and anodic electrochemical behavior of additive manufactured Hastelloy X alloy via directed energy deposition

Additive manufacturing of tantalum-zirconium alloy coating for corrosion and wear application by laser directed energy deposition on Ti6Al4V

Improving the fatigue property of 316L stainless steel through direct energy deposition technology

Microstructure and Wear Resistance of Laser Cladding nano TiC/micro TiB2/C-276 Composite Coatings on 316L Stainless Steel

Interfacial Alloying Between Expanded Austenite and Ti(AlCu)N Coating for Enhanced Cavitation Erosion Resistance

Microstructure and Properties of AlCoCrFeNiSi High-Entropy Alloy Coating on AISI 304 Stainless Steel by Laser Cladding

Microstructure evolution and high temperature corrosion behavior of FeCrBSi coatings prepared by laser cladding