Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Self-supporting Biomass Li–S Cathodes Decorated with Metal Phosphides–Higher Sulfur Loading, Better Stability, and Longer Cycle Life

Surface-coated AlF3 Nanolayers Enable Polysulfide Confinement Within Biomass-Derived Nitrogen-Doped Hierarchical Porous Carbon Microspheres for Improved Lithium-Sulfur Batteries

Biomass-derived self-supporting sulfur host with NiS/C composite for high-loading Li-S battery cathode

High-performance Li–S Battery Cathode with Catalyst-Like Carbon Nanotube-Mop Promoting Polysulfide Redox

Efficient Activation of Li2S by Transition Metal Phosphides Nanoparticles for Highly Stable Lithium–Sulfur Batteries

Cobalt-Doped Sns2 With Dual Active Centers Of Synergistic Absorption-Catalysis Effect For High-S Loading Li-S Batteries

Naturally derived honeycomb-like N,S-codoped hierarchical porous carbon with MS2 (M = Co, Ni) decoration for high-performance Li-S battery

Fast conversion and controlled deposition of lithium (poly)sulfides in lithium-sulfur batteries using high-loading cobalt single atoms

Li 2 S In Situ Grown on Three-Dimensional Porous Carbon Architecture with Electron/Ion Channels and Dual Active Sites as Cathodes of Li–S Batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

Facilitation polysulfides adsorption/catalysis by nitrogen/phosphorous co-doped carbon nanofibers networks for advanced lithium/polysulfides batteries

Promoting “strong Adsorption” and “fast Conversion” of Polysulfides in Li‐S Batteries Based on Conductive Sulfides Host with Hollow Prism Structure and Surface Defects

Self-templating synthesis of prismatic-like N-doped carbon tubes embedded with Fe3O4 as a high-efficiency polysulfide-anchoring-conversion mediator for high performance lithium-sulfur batteries

Flexible and Self-Supported Sulfur Cathode for High-Energy-Density Lithium-Sulfur Batteries

Co-Fe Mixed Metal Phosphide Nanocubes with Highly Interconnected-Pore Architecture as an Efficient Polysulfide Mediator for Lithium-Sulfur Batteries

Metallic and Polar Co 9 S 8 Inlaid Carbon Hollow Nanopolyhedra As Efficient Polysulfide Mediator for Lithium−sulfur Batteries

A strategy to achieve high loading and high energy density Li-S batteries

Coordinated Immobilization and Rapid Conversion of Polysulfide Enabled by a Hollow Metal Oxide/Sulfide/Nitrogen‐Doped Carbon Heterostructure for Long‐Cycle‐Life Lithium‐Sulfur Batteries

Free-Standing Sulfur Cathodes Enabled by a Cationic Polymer for Lean Electrolyte Lithium–Sulfur Batteries

Three-dimensional Spongy Framework As Superlyophilic, Strongly Absorbing, and Electrocatalytic Polysulfide Reservoir Layer for High-Rate and Long-Cycling Lithium-Sulfur Batteries

Phosphotungstic acid decorated free-standing electrode accelerates polysulfides conversion for high-performance flexible Li S batteries