Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Cobalt-Doped Sns2 With Dual Active Centers Of Synergistic Absorption-Catalysis Effect For High-S Loading Li-S Batteries

A Freestanding Flexible Single‐Atom Cobalt‐Based Multifunctional Interlayer Toward Reversible and Durable Lithium‐Sulfur Batteries

Confined Co9S8 nanocrystals into N/S-Co-doped Carbon Nanofibers as A Chainmail-like Electrocatalyst for High-performance Lithium-Sulfur Batteries with High Sulfur Loading

An Entangled Cobalt–Nitrogen–Carbon Nanotube Array Electrode with Synergetic Confinement and Electrocatalysis of Polysulfides for Stable Li–S Batteries

Fast conversion and controlled deposition of lithium (poly)sulfides in lithium-sulfur batteries using high-loading cobalt single atoms

Preparation of CoO/SnO2@NC/S composite as high-stability cathode material for lithium-sulfur batteries

Highly active CoP-Co2N confined in nanocarbon enabling efficient electrocatalytic immobilizing-conversion of polysulfide targeting high-rate lithium-sulfur batteries

Promoting polysulfide conversions via cobalt single-atom catalyst for fast and durable lithium-sulfur batteries

Synergistic restriction of polysulfides enabled by cobalt@carbon spheres embedded CNTs: A facile approach for constructing sulfur cathodes with high sulfur content

Catalytic Interfaces‐Enriched Hybrid Hollow Spheres Sulfur Host for Advanced Li–S Batteries

CoS2-NC@CNTs hierarchical nanostructures for efficient polysulfide regulation in lithium-sulfur batteries

N-Doped Carbon Fiber-Encapsulated CoS 2 /SnS 2 Heterostructures Facilitate Polysulfide Conversion for Lithium–Sulfur Batteries

A hollow Co0.12Ni1.88S2/NiO heterostructure that synergistically facilitates lithium polysulfide adsorption and conversion for lithium-sulfur batteries

Nitrogen Doped Carbon Nanosheets Encapsulated in Situ Generated Sulfur Enable High Capacity and Superior Rate Cathode for Li-S Batteries

Cobalt-induced Highly-electroactive Li 2 S Heterostructured Cathode for Li-S Batteries

Synergistic effect of selectively etched CoFe and N-doped hollow carbon spheres for high performance lithium-sulfur batteries

Boosting the Rate Performance of Li-S Batteries Via Highly Dispersed Cobalt Nanoparticles Embedded into Nitrogen-Doped Hierarchical Porous Carbon

Single-atomic Co-B2N2 sites anchored on carbon nanotube arrays promote lithium polysulfide conversion in lithium-sulfur batteries

Embedding cobalt (II, III) oxide nanoparticles into nitrogen-doped carbon nanotubes-grafted hollow polyhedrons as sulfur hosts for ultralong-life lithium-sulfur batteries

Nitrogen-Doped CoP with optimized d-Band center as bidirectional electrocatalyst for high areal capacity of Li-S battery

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries