Abstract:Highly efficient and stable, rigid and flexible p‐i‐n perovskite solar cells are developed by incorporating a 2‐(acetyloxy)‐N,N,N‐trimethylethanium chloride additive into the lead iodide precursor solution to prepare a porous PbI2 layer. The good diffusion of the organic ammonium salt results in flat and dense perovskite film with large particle size, which achieves high power conversion efficienciesPCE of 23.40% (rigid) and 21.10% (flexible) with excellent ambient and mechanical stability. Flexible perovskite solar cells (FPSCs) are attracting widespread research and attention for their benefits as the next‐generation wearable electronic products. However, there are still many challenges in the quest to achieve dense, pinhole‐free, high crystal quality, low defect, and stable perovskite films, which limit further improvement in the efficiency and stability of FPSCs. Herein, a novel technique for the incorporation of quaternary ammonium halide (QAH) additives to prepare fluffy porous lead iodide layers by using a two‐step sequential deposition method, is reported. Benefiting from the good diffusion of organic amine salts on porous PbI2 layers, flat and dense perovskite films are produced with large particle sizes, few defects, and high crystal quality. Finally, the champion rigid and flexible p‐i‐n PSCs with the 2‐(acetyloxy)‐N,N,N‐trimethylethanium chloride (AtaCl) additive achieves exciting power conversion efficiencies (PCE) of 23.40% and 21.10%, respectively. The device with the AtaCl additive retains over 90% of its original PCE under ambient conditions (40 ± 5% relative humidity (RH)) over 1000 h of aging without encapsulation. In addition, the flexible device with the AtaCl additive shows excellent stability under mechanical bending conditions, retaining ≈85% of its original PCE after 10 000 cycles (bending radius = 5 mm).

An efficient, flexible perovskite solar module exceeding 8% prepared with an ultrafast PbI2 deposition rate

Flexible Perovskite Solar Modules with Functional Layers Fully Vacuum Deposited

Pseudohalide-Induced Recrystallization Engineering for CH3NH3PbI3 Film and Its Application in Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells

A fast deposition-crystallization procedure for highly efficient lead iodide perovskite thin-film solar cells

Direct Conversion of CH3NH3PbI3 from Electrodeposited PbO for Highly Efficient Planar Perovskite Solar Cells

Facile and Scalable Fabrication of Highly Efficient Lead Iodide Perovskite Thin-Film Solar Cells in Air Using Gas Pump Method

Porous Lead Iodide Layer Promotes Organic Amine Salt Diffusion to Achieve High Performance p‐i‐n Flexible Perovskite Solar Cells

Rapid and Complete Conversion of CH3NH3PbI3 for Perovskite/C60 Planar-Heterojunction Solar Cells by Two-Step Deposition

Negligible‐Pb‐Waste and Upscalable Perovskite Deposition Technology for High‐Operational‐Stability Perovskite Solar Modules

Fast and Controllable Electric-Field-Assisted Reactive Deposited Stable and Annealing-Free Perovskite toward Applicable High-Performance Solar Cells

Two-step Ultrasonic Spray Deposition of CH3NH3PbI3 for Efficient and Large-Area Perovskite Solar Cell

High Efficient Planar-heterojunction Perovskite Solar Cell Based on Two-step Deposition Process

High Efficient Planar-Heterojunction Solar Cells Achieved by Using A Smooth Ch3nh3pbi3 Film Via A New Approach of Forming the Pbi2 Nanostructure Together with Strategically High Ch3nh3i Concentration

An Up-Scalable Approach to CH3NH3PbI3 Compact Films for High-Performance Perovskite Solar Cells

A facile spray-assisted fabrication of homogenous flat CH3NH3PbI3 films for high performance mesostructure perovskite solar cells

Scalable Fabrication of High‐Performance Perovskite Solar Cell Modules by Mediated Vapor Deposition

An ultrahigh 84.3% fill factor for efficient CH3NH3PbI3 P-i-N perovskite film solar cell

Highest‐Efficiency Flexible Perovskite Solar Module by Interface Engineering for Efficient Charge‐Transfer

Smooth CH3NH3PbI3 from controlled solid–gas reaction for photovoltaic applications

Ionic Liquid Stabilized Perovskite Solar Modules with Power Conversion Efficiency Exceeding 20%

Low-temperature solution-processed perovskite solar cells with high efficiency and flexibility.