Abstract:This study has investigated the structure and mechanical properties of pure Zr and a series of binary Zr–Ti alloys in order to determine their potential application as dental implant materials. The titanium contents of these alloys range from 10 to 40wt.% and were prepared by arc melting in inert gas. This study evaluated the phase and structure of these Zr–Ti alloys using an X-ray diffraction (XRD) for phase analysis, and an optical microscope for microstructure analysis of the etched alloys. Three-point bending tests were performed to evaluate the mechanical properties of all specimens. The experimental results indicated that the pure Zr and Zr–10Ti comprised entirely of an acicular hexagonal structure of α′ phase. When the Ti content increased to 20wt.%, a significant amount of β phase was retained. However, when the Ti content increased to 40wt.%, only the equi-axed, retained β phase was observed in the cast alloy. Moreover, the hardness values and bending strengths of the Zr–Ti alloys decreased with an increasing Ti content. Among pure Zr and Zr–Ti alloys, the α′-phase Zr–10Ti alloy has the greatest hardness and bending strength. The pure Zr and Zr–Ti alloys exhibit a similar elastic modulus ranging from 68GPa (Zr–30Ti) to 78GPa (Zr–40Ti). Based on the results of elastic moduli, pure Zr and Zr–Ti alloys are found to be suitable for implant materials due to lower modulus. Like bending strength, the elastically recoverable angle of Zr–Ti alloys decreased as the concentration of Ti increased. In the current search for a better implant material, the Zr–10Ti alloy exhibited the highest bending strength/modulus ratios as large as 25.3, which are higher than that of pure Zr (14.9) by 70%, and commercially pure Ti (8.7) by 191%. Thus, Zr–Ti alloy's low modulus, ductile property, excellent elastic recovery capability and impressive strength confirm that it is a promising candidate for dental implant materials.

Structure, mechanical properties, and grindability of dental Ti–Zr alloys

Effects of Zr Addition on the Deformation Behavior, Microstructure and Mechanical Properties of Dental Ti Alloys

Development and properties of dental Ti–Zr binary alloys

Microstructure, mechanical properties, and preliminary biocompatibility evaluation of binary Ti–Zr alloys for dental application

The structure and mechanical properties of as-cast Zr–Ti alloys

Microstructure and Mechanical Properties of Ti-Zr-Cr Biomedical Alloys.

The effect of the solute on the structure, selected mechanical properties, and biocompatibility of Ti–Zr system alloys for dental applications

Titanium-Zirconium Binary Alloy as Dental Implant Material: Analysis of the Influence of Compositional Change on Mechanical Properties and In Vitro Biologic Response.

Cytocompatibility of Ti–xZr Alloys As Dental Implant Materials

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Cytocompatibility, Stability and Osteogenic Activity of Powder Metallurgy Ta-xZr Alloys As Dental Implant Materials

Biocompatibility and Osteogenic Activity of Zr?30Ta and Zr?25Ta?5Ti Sintered Alloys for Dental and Orthopedic Implants

Vacuum sealing-assisted processing of titanium–zirconium alloys: synthesis, microstructure, hardness, friction, wear, and corrosion studies for biomedical application

Suitability of Ti–Zr Alloy for Dental Implants: Tribocorrosion Investigation

Effect of Zr on Microstructure and Mechanical Properties of Binary TiAl Alloys

Effect of zirconium content on the microstructure, physical properties and corrosion behavior of Ti alloys

Microstructures and Properties of Titanium Alloys Ti-Mo for Dental Use

Microstructure and Mechanical Properties of Ti43Al6Nb Alloys with Different Zirconium Contents

Tribological Behaviour of Biomedical Ti–Zr-based Shape Memory Alloys

Influence of Zr Content on Microstructure and Mechanical Properties of Implant Ti–35Nb–4Sn–6Mo–xZr Alloys

Microstructure, mechanical properties and osseointegration ability of Ta-20Zr alloy used as dental implant material