Abstract:We conducted a study to investigate the impact of the laser direct metal deposition (LMD) process on the microstructure, mechanical properties, temperature fields, and stress fields of 24CrNiMo steel in order to determine the optimal process parameters. The optimal parameters were determined to be a laser power of 1400 W, scanning speed of 7 mm/s, and powder feed rate of 8 g/min. When these optimal parameters were used, the formed specimens exhibited a high densely of up to 97.5 %. The microstructure of the specimens formed different parameters primarily consisted of bainite, martensite and ferrite. The specimens formed under various process conditions demonstrated good toughness, with a maximum tensile strength of 1131±20 MPa and an elongation of 16±1.8 %. Additionally, there was little difference in wear resistance and wear morphology among the specimens formed under different processes. The predominant wear mechanisms include abrasive wear, adhesive wearand oxidative wear. Increasing laser power and decreasing scanning speed resulted in a gradual increase in the temperature gradient gradually, leading to higher residual stresses in the formed specimens. Longitudinal stresses concentrated on both sides of the deposited layer, while the transverse stresses concentrated on one side of the deposited layer. The simulation results of the temperature field and stress field were consistent with the experimental results, with errors within the range of 10 %–20 %. This study demonstrated that the simulated models of temperature and stress fields effectively captured the fundamental phenomena in the LMD process, providing valuable tools for predicting and optimizing temperature distribution and stress in the LMD process. These findings contribute to the understanding and enhancement of the LMD process for 24CrNiMo steel, making it applicable for various applications requiring superior microstructure and mechanical properties.

Multi-objective optimisation of process parameters for laser-based directed energy deposition of a mixture of H13 and M2 steel powders on 4Cr5Mo2SiV1 steel

A hybrid directed energy deposition process to manipulate microstructure and properties of austenitic stainless steel

Anisotropic dynamic compression response of an ultra-high strength steel fabricated by laser hybrid additive manufacturing

Multi-objective optimization of laser cladding process parameters for Q345B steel

Multi-Objective Optimization of Process Parameters in Laser Cladding CoCrCuFeNi High-Entropy Alloy Coating

Multi-objective optimization in titanium powder mixed electrical discharge machining process parameters for die steels

Achieving high hardness and wear resistance in phase transition reinforced DC53 die steel by laser additive manufacturing

Numerical simulation on melt pool and solidification in the direct energy deposition process of GH3536 powder superalloy

Process parameter optimization of K477 and GH4169 for defect control in laser-directed energy deposition using Taguchi design of experiments

Development of Robust Steel Alloys for Laser-Directed Energy Deposition via Analysis of Mechanical Property Sensitivities

Optimized bilateral ultrasonic surface rolling process assisting directed energy deposition of thin-walled medium-entropy alloy with high mechanical performance

Process Parameter Optimization of Directed Energy Deposited QT17‐4+ Steel

Multi-response optimization of M2 steel coatings deposited by co-axial laser cladding on A2 steel tool surfaces

Effect of closed-loop controlled melt pool width on microstructure and tensile property for Fe-Ni-Cr alloy in directed energy deposition

Composition fine-tuning for directed energy deposition of Ti-6Al-4V

Multi-objective Optimization in Selective Laser Melting of AlSi10Mg Alloy Based on Response Surface Methodology

Tailoring Microstructure Evolution and Mechanical Properties of a High-Performance Alloy Steel Through Controlled Thermal Cycles of a Direct Laser Depositing Process

Investigation on the Process and Microstructure Evolution During Direct Laser Metal Deposition of 18Ni300

Effect of laser direct metal deposition process on the microstructure and mechanical properties and temperature and stress fields of 24CrNiMo

An Integrated Method for Multi-Objective Optimization of Multi-Pass Fe50/TiC Laser Cladding on AISI 1045 Steel based on Grey Relational Analysis and Principal Component Analysis

Programmable mechanical properties of additively manufactured novel steel