Abstract:The divertor first wall and neutral beam injection (NBI) components of tokamak devices require high heat flux removal up to 20–30 MW m−2 for future fusion reactors. The water cooled HyperVapotron (HV) structure, which relies on internal grooves or fins and boiling heat transfer to maximize the heat transfer capability, is the most promising candidate. The HV devices, that are able to transfer large amounts of heat (1–20 MW m−2) efficiently, have therefore been developed specifically for this application. Until recently, there have been few attempts to observe the detailed bubble characteristics and vortex evolvement of coolant flowing inside their various parts and understand of the internal two-phase complex heat transfer mechanism behind the vapotron effect. This research builds the experimental facilities of HyperVapotron Loop-I (HVL-I) and Pressure Water HyperVapotron Loop-II (PWHL-II) to implement the subcooled boiling principle experiment in terms of typical flow parameters, geometrical parameters of test section and surface heat flux, which are similar to those of the ITER-like first wall and NBI components (EAST and MAST). The multiphase flow and heat transfer phenomena on the surface of grooves and triangular fins when the subcooled water flowed through were observed and measured with the planar laser induced fluorescence (PLIF) and high-speed photography (HSP) techniques. Particle image velocimetry (PIV) was selected to reveal vortex formation, the flow structure that promotes the vapotron effect during subcooled boiling. The coolant flow data for contributing to the understanding of the vapotron phenomenon and the assessment of how the design and operational conditions that might affect the thermal performance of the devices were collected and analysed. The subcooled flow boiling model and methods of HV heat transfer adopted in the considered computational fluid dynamics (CFD) code were evaluated by comparing the calculated wall temperatures with the experimentally measured values. It was discovered that the bubble and vortex characteristics in the HV are clearly heavily dependent on the internal geometry, flow conditions and input heat flux. The evaporation latent heat is the primary heat transfer mechanism of HV flow under the condition of high heat flux, and the heat transfer through convection is very limited. The percentage of wall heat flux going into vapour production is almost 70%. These relationships between the flow phenomena and thermal performance of the HV device are essential to study the mechanisms for the flow structure alterations for design optimization and improvements of the ITER-like devices' water cooling structure and plasma facing components for future fusion reactors.

Numerical Analysis of the Influence of Side Slot and Fin Heights in a Hypervapotron Channel on Heat Transfer

Analysis and Optimization of Cooling Channels in ITER Blanket Module

Thermohydraulic Performance Optimization of Integrated Porous Pin Fins in Microchannel Heat Sink Using Shape Optimization Coupled with NSGA

Experimental Investigation on Heat Transfer Characteristics of a Novel Hypervapotron Channel for Divertor Target in Nuclear Fusion Reactors

Effect of Hypervapotron Fin Angle on Subcooled Flow Boiling Heat Transfer Performance Under One-Side High-Heat Load Condition

Hierarchical Hypervapotron Structure Integrated with Microchannels for Advancement of Thermohydraulic Performance

Numerical Investigations of Heat Transfer in Hybrid Microchannel Heat Sink with Multi-Jet Impinging and Trapezoidal Fins

Numerical Investigation of Fluid Flow and Heat Transfer in High-Temperature Wavy Microchannels with Different Shaped Fins Cooled by Liquid Metal

Effect of fin shapes on flow boiling heat transfer with staggered fin arrays in a heat sink

Flow and Thermal Analysis of the Transition Scheme Between Micro-Channel and Micro-Jet Cooling Solution

Experimental Study of Hypervapotron under Conditions of High Heat Flux

Experimental and numerical investigation on turbulent convection enhancement in minichannel heat sink with staggered V-shaped pin fins

Experimental and numerical investigation on the heat transfer enhancement for Mini-channel heat sinks with tessellated fins

Heat transfer enhancement using combined microchannel with vertical rectangular micro fins

Numerical study on hydrothermal performance in a microchannel with gradient array of ribs and pin fins

Study on the flow and heat transfer characteristics of a hybrid nanofluid jet impingement microchannel heat sink with airfoil fins

Experimental and Numerical Investigation of HyperVapotron Heat Transfer

PIV and thermal-vision experimental and numerical investigation on the airside performance of slotted fin surfaces

Numerical investigations of heat transfer augmentation in a microchannel heat sink with different shaped periodic reentrant cavities on channel sidewalls

Experimental and Numerical Study on Thermofluidic Characteristics of Microchannel Heat Sinks with Various Micro Pin–fin Arrays Arrangement Patterns

Numerical Analysis of Flow Boiling Characteristics of a Single Channel Heat Sink Subjected to Multiple Heat Sources