Abstract:Aim: To evaluate the effect of various rotational motions on the torque/force generation, surface wear, and shaping ability of the ProGlider glide path instrument (Dentsply Sirona). Methodology: Mesiobuccal and mesiolingual canals of mandibular molars were selected based on the canal volume, length, angle of curvature (25°-40°), and radius of curvature (4-8 mm) after micro-computed tomographic scanning. The samples were randomly assigned to four groups (n = 13, each) according to movement kinematics [continuous rotation (CR; 300 rpm), optimum torque reverse motion (OTR; 180° forward and 90° reverse when torque >0.4 N cm), time-dependent reciprocal motion (TmR; 180° forward and 90° reverse), and optimal glide path motion (OGP; a combination of 90° forward, 90° reverse, 90° forward, and 120° reverse)]. Instrumentation was performed with an automated root canal instrument and torque/force analysing device. Maximum torque/force values, canal volume changes, and canal-centring ratios at 1, 3, 5, and 7 mm were evaluated. Surface defects (pits, grooves, microcracks, blunt cutting edges, and disruption of cutting edges) and spiral distortion on the ProGlider instrument were scored at the tip and 5 mm short of the tip before and after five consecutive uses with scanning electron microscopy. The Kruskal-Wallis test followed by Dunn's post-test with Bonferroni correction and Wilcoxon signed-rank test were used to analyse the data (α = 0.05). Results: Optimal glide path motion generated significantly less clockwise torque and greater upward force than other groups (p < .05). OGP resulted in significantly fewer surface defects than CR (p < .05). In OGP and CR, the tip exhibited more surface defects than 5 mm short of the tip (p < .05). CR resulted in greater volume changes than OGP and TmR (p < .05) and greater centring ratios (i.e., more deviation) than OGP at 1 mm and OTR at 3 mm (p < .05). Conclusions: Under laboratory conditions using the ProGlider instrument, OGP generated significantly less clockwise torque and greater upward force than the other rotatory motions. OGP generated fewer superficial defects than CR, and the three modes of reciprocal rotation better maintained the apical curvature of root canals than CR with the ProGlider instrument.

Surface Changes of PathFile after Glide Path Preparation: An Ex Vivo and In Vivo Study

[Glide Path Management of Rotary Nickel-Titanium Instruments in Simulated Root Canals].

Comparison of the effect of different glide path files on amount of apically extruded debris in curved root canals

Glide Path in Endodontics: A Literature Review of Current Knowledge

Comparative Evaluation of the Cyclic Fatigue Resistance of WaveOne Gold in Reciprocation, ProGlider in Rotary Motion, and Manual Files in a Reciprocating Handpiece Within Simulated Curved Canals: An In Vitro Study

Shaping ability of rotary and reciprocating single-file systems in combination with and without different glide path techniques in simulated curved canals

Effect of glide path preparation on the apical debris extrusion for three single-file systems

Effect of kinematics on the torque/force generation, surface characteristics, and shaping ability of a nickel-titanium rotary glide path instrument: An ex vivo study

Microcomputed tomography analysis of curved root canal preparation when coronal flaring and glide path files used with heat-treated nickel titanium rotary files

Comparative Evaluation of Surface Roughness of Different Rotary Nickel-Titanium (NiTi) Files After Autoclaving: An Atomic Force Microscopic Study

Evaluation of shaping ability of different glide path instruments: a micro-computed tomography study

Evaluation of design, mechanical properties, and torque/force generation of heat-treated NiTi glide path instruments

Comparative evaluation of volumetric changes between two pediatric rotary files (Kedo-S plus, Kedo-SG blue) and manual files (hand K-files) during canal preparation of primary mandibular molars: an in-vitro nano-CT analysis

Apical extrusion of debris during the preparation of oval root canals: a comparative study between a full-sequence SAF system and a rotary file system supplemented by XP-endo finisher file

Gentlefile Versus Protaper in the Shaping Ability in Simulated J-shaped Root Canals

Scanning electron microscopy analysis of conventional and controlled-memory nickel titanium files before and after multi-uses in root canals

In Vitro Evaluation Of The Dynamic Cyclic Fatigue Resistance Of A New Trunatomy Glider File After Different Cycles Of Use

Evaluation of Volumetric Changes between Pediatric Rotary Files and Manual Files during Canal Preparation of Primary Mandibular Canine: A Nano-CT Analysis

Shaping effectiveness and surface topography of reciprocating files after multiple simulated uses

Comparison of hand, rotary, reciprocating and self-adjusting files in cleaning mesio-buccal canals of maxillary first molars

Evaluating In Vitro Performance of a Novel Stainless Steel Rotary System (Gentlefile) Based on Debris Extrusion and Instrumentation Time