Abstract:With the fast growth in emerging technologies for mobile applications, packaging solutions are being driven by advanced Silicon (Si) nodes technology (down to 7nm), smaller form factor package designs, efficiency enhancement and lower power consumption. The flip chip chip scale package (fcCSP) has been widely adopted as the solution for mobile devices to satisfy these challenging requirements. In order to create a lower cost solution, the fcCSP uses the cost-effective combination of copper (Cu) pillar bumps, embedded trace substrate (ETS) technology, mass reflow (MR) chip attach and molded underfill (MUF) processes. Although the utilization of MR chip attach is a cost-effective process for flip chip package assembly, there is a high risk for a bump to trace short, especially for the designs with finer bump pitch and line width / line spacing (LW/LS) with an escaped trace. To reduce this risk, the laser assisted bonding (LAB) methodology is introduced to study the 7nm chip-package interaction (CPI) of an fcCSP with a 60µm bump pitch and escaped traces design in this paper. For the purpose of measuring the extremely low-k (ELK) performance in a 14x14mm fine pitch fcCSP with 7nm live die, the thunder test (two-times MR and quick temperature cycling (QTC) tests) as well as the hammer test with multi-reflow process (peak temperature at 260ºC) have been evaluated after performing LAB and MR chip attach methodologies. The results show that although both chip attach methodologies can pass the normal requirements of the thunder and hammer tests, the utilization of LAB technology can further enhance the strength of ELK and produce better yield performance. From these results, it is believed that LAB not only can guarantee assembly yield with less ELK damage risk in the examined 7nm fcCSP, but can also accommodate Si node and bump pitch reduction with a finer LW/LS substrate with escaped traces design.

Process Development of micro-bump flip chip bonding with Non-Conductive Film

Process Development of A New Tgv Interposer for Wafer Level Package of Inertial Mems Device

Fluxless Flip Chip Bonding Tech Application for Ultra-High Density Micro-bump Structure

Optimization of Bonding Methods for Controlling Sn Spillage in Fine Pitch Microbump Applications

Development of Hybrid Bonding Process for Embedded Bump with Cu-Sn/BCB Structure

A Study on Improvement and Extension of Fine-Pitch Micro-Bump Interconnects Technology: New Metallurgy & Flux-Less Oxide-removal Laser Assembly (FLOLA)

Micro-Cantilever Array With Electroplating Tin Bumps for Flip-Chip Bonding Technology

The Research on a Low Cost Flip Chip Bumping Process by Stencil Printing

Effects of Bonding Parameters on the Reliability of Fine-Pitch Cu/Ni/SnAg Micro-Bump Chip-to-Chip Interconnection for Three-Dimensional Chip Stacking

Fine-pitch bonding technology with surface-planarized solder micro-bump/polymer hybrid for 3D integration

A Cu-Sn/BCB Hybrid Bonding with Embedded Bump Structure

Fine Pitch Micro Indium Bump Interconnect Flip Chip Bonding

Novel design and reliability assessment of a 3D DRAM stacking based on Cu-Sn micro-bump bonding and TSV interconnection technology

Optimization of Micro-interconnection Distribution of Gold Stud Bumps for Thermo-sonic Flip Chip Bonding

Bonding Property of Flip-Chip Chip-Scale Package with Vacuum Reflow and Thermal Compression Bonding Processes

Effects of Commercial No-Clean Flux on Reliability of Fine Pitch Flip-Chip Package With Solder Bumps and Copper Pillars

7nm Chip-Package Interaction Study on a Fine Pitch Flip Chip Package with Laser Assisted Bonding and Mass Reflow Technology

Cu–Cu Bonded Microbump Interconnects with a 10- $\mu$ M Pitch for 3-D-stacked Chiplets

Bonding of 5 Μm Cu-Sn Micro Bumps Using Thermal Reflow and Solid-State Pre-Bonding

Low-Temperature Ultrasonic Bonding of Cu/Sn Microbumps with Au Layer for High Density Interconnection Applications

In Situ Study on Cu-to-Cu Thermal Compression Bonding