[Conversion of C8 of guanine to a l carbon unit during biosynthesis of riboflavin].

D. Hayes,G. R. Greenberg

Abstract:

What problem does this paper attempt to address?

Coherent OTDR Based Ultra-High Sensitive Acoustic Sensor Assisted with Distributed Microstructured Optical Fiber(DMOF) and Hollow Cylinder Transducer

Hao Li,Fan Ai,Jingyi Wang,Wei Zhang,Zhikun Xing,Zhijun Yan,Deming Liu,Qizhen Sun

DOI: https://doi.org/10.1109/ICAIT.2018.8686722

2018-01-01

Abstract:An ultra-high sensitive distributed microstructured optical fiber (DMOF) acoustic sensor based on coherent OTDR demodulation method and hollow cylinder transducer is presented. As a consecutive longitudinal microstructured optical fiber, the DMOF contains backscattering enhanced points which greatly improved the signal to noise ratio(SNR) of the acoustic sensing signal. Based on coherent OTDR demodulation method, the amount of phase change caused by sound pressure can be directly obtained. In order to increase the phase sensitivity, sensing fiber between two backscattering enhanced points along the DMOF is wrapped on a hollow cylinder transducer as an acoustic sensing unit. Finally, experiments on detecting sound waves in air are carried out. The results demonstrate that our fiber acoustic sensor has a flat sensitivity frequency response from 500Hz to 5kHz with a phase sensitivity of around -112dB(re rad/μPa) and a peak sensitivity of -83.7dB at 80Hz. It is noteworthy that the sensing mechanism based on the DMOF can be further extended to distributed acoustic sensing.
Radio-frequency Detection of Partial Discharge in Power Cable Joints

Xiao Hu,Shaocai Yang,Qing Du,Xiangrong Chen,Fuxin Tang

DOI: https://doi.org/10.1109/tpwrd.2023.3334310

IF: 4.825

2024-01-01

IEEE Transactions on Power Delivery

Abstract:Partial discharge (PD) is indicative of insulation defects in power cable joints. Cross-bonding cable joints have a break in the joint shield that interrupts the screen of the jointed cables. It is possible for radio frequency (RF) signals of PD in the joints to emit from the shield break. This paper presents the use of off-the-shelf RF sensors at the shield break for non-intrusive PD detection. Measuring results from a 35 kV XLPE cable joint sample with artificial defects suggest that PD-induced electric and magnetic fields can be detected simultaneously with this approach. Typical pulses measured are limited to approximately 500 ns in duration, and the FFT spectrum of the pulses is mainly distributed at frequencies below 200 MHz. Average pulse magnitude ranging from about 6 to 22 mV can be measured between 10-15 kV. Increasing the measuring distance can cause the measured pulse magnitude to decease exponentially. Additionally, numerical simulations show that reducing the length of the shield break can cause the pulse magnitude recorded at the shield break to decrease gradually. The presented approach can potentially be used for cost-effective and non-intrusive detection of PD in cross-bonding cable joints.
A High Sensitivity Optical Fiber Interferometer Sensor for Acoustic Emission Detection of Partial Discharge in Power Transformer

Hong-Yang Zhou,Guo-Ming Ma,Meng Zhang,Han-Chi Zhang,Cheng-Rong Li

DOI: https://doi.org/10.1109/jsen.2019.2951613

IF: 4.3

2021-01-01

IEEE Sensors Journal

Abstract:We propose a Michelson ultrasonic sensing system for detecting the acoustic emission generated by the partial discharge in power transformer. In order to guide the sensor head design in the sensing system for high sensitivity, a theoretical model is established to investigate the effects of the sensor head dimensions on the response sensitivity. After that, an optimized sensor head is designed. In the frequency range from 80 kHz to 200 kHz, whether the PZT sensor is installed in the oil or on the tank, the average response sensitivity of the proposed sensing system is higher than that of the conventional PZT system. When the distance between the sensor head and ultrasonic source is 300 mm in oil, the average detection limit of the Michelson ultrasonic sensing system is about 0.26 Pa, which is about 18.6% of that of the PZT system. Moreover, experiment results show that the detectable partial discharge initial voltage for the proposed optical system is 21.5% lower than that for the PZT system. The enhanced sensitivity makes the Michelson ultrasonic sensing system a potential method to detect the small defects in power transformer.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
Implementation of a Fiber-Wrapped Polymer Mandrel Acoustic Emission Sensor

Zhangwei Wang,Jianxun Lv,Peng Wei,Haiwen Yuan

DOI: https://doi.org/10.1109/jsen.2021.3135289

IF: 4.3

2022-02-01

IEEE Sensors Journal

Abstract:Fiber-optic sensors show advantages in acous- tic emission (AE) detection of power equipment due to their galvanic isolation and immunity to electromagnetic interference (EMI). This paper proposes a fiber-wrapped polymer mandrel (FWPM) acoustic emission sensor based on the Mach-Zehnder interferometer. The mechanism model of the sensing head is established using displacement function and state equation. The finite element analysis shows that the wrapped length of the optical fiber, the geometric parameters, and the mechanical properties of the polymer mandrel affect the frequency response of the FWPM AE sensor. The theoretical analysis and experimental results show that the proposed sensor is sensitive to 30–200 kHz AE waves and has good linearity. The FWPM AE sensing system has a lower detection limit than the piezoceramics (PZT) sensing systems. The FWPM AE sensing system is expected to provide significant support for solving the health monitoring of ultra-high voltage (UHV) equipment.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
A Partial Discharge Detection System for XLPE Cable Terminals and Acoustic Wave Sensing Characteristics Based on Fiber Optic Mach-Zehnder Interferometer

Yanpeng Hao,Yanwen Chen,Yun Chen,Tao Huang,Jiapeng Xiao,Lin Yang

DOI: https://doi.org/10.1109/jsen.2021.3101835

IF: 4.3

2021-10-01

IEEE Sensors Journal

Abstract:Monitoring the cable terminal's partial discharge (PD) is of great significance to ensure the cable line's safe and stable operation. To improve the anti-interference ability and real-time performance of partial discharge detection, this paper develops a partial discharge Mach-Zehnder interferometer (MZI) detection system for cross-linked polyethylene (XLPE) cable terminals. The optical fiber is implanted into the 10 kV XLPE cable terminal, and airgap defects of different volumes are set in the main insulation. The optical fiber inside the cable terminal serves as the sensing head of the MZI signal arm. PD test was carried out on the samples, and the test results of fiber optic MZI and high-frequency current transformer (HFCT) were compared and analyzed. The results showed that the 10 kV XLPE cable terminal does not produce PD due to optical fiber implantation. The partial discharge of 196 pC can be recognized by the fiber optic MZI for the cylindrical airgap defect sample with a base radius of 1.5 mm and a height of 3 mm. For the cylindrical airgap defect sample with a base radius of 1.5 mm and a height of 1 mm, the sensitivity of partial discharge detection by fiber optic MZI is higher than that by HFCT. The sensitivity of partial discharge inception voltage (PDIV) detection is increased by 27.5%.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
Flexible Pb(Zr0.52,Ti0.48)O3 thin film acoustic emission sensor for monitoring partial discharge in power cable

Ming Wu,Yu Yan,Yanan Xiao,Yongbin Liu,Huaqiang Li,Lisheng Zhong,Xiaojie Lou,Jinghui Gao

DOI: https://doi.org/10.1063/5.0135445

IF: 1.697

2023-03-08

AIP Advances

Abstract:Piezoelectric acoustic emission sensors can be used detect the sound emitted by the target structure when it is damaged and have important applications in the field of structure health monitoring. However, due to the mismatch of the interface acoustic impedance, it is hard for the conventional ultrasonic sensor to monitor the acoustic emission in a pipe structure. In this work, a flexible sensor by the deposition of a Pb(Zr 0.52 ,Ti 0.48 )O 3 thin film on a mica substrate was fabricated, and the acoustic emission generated by the partial discharge of a 110 kV power cable was detected by using the flexible sensor. The flexible sensor was designed with an electromagnetic shielding structure and, therefore, can screen most of the electromagnetic interference. The flexible sensor shows a relatively flat response in the frequency range from 100 to 1000 kHz with a sensitivity over 47.5 dB, which is beneficial for pattern recognition studies of acoustic emission. This work not only provides a flexible, anti-electromagnetic interference and broadband sensor for acoustic emission detection but also promotes the development and application of flexible ferroelectric materials.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
Highly Sensitive Acoustic Emission Sensor Based on Polarization-maintaining and Absorption-reducing Polarization-maintaining Fiber

Xuefeng Li,Yin Zhang,Hexin Cao,Xinyu Zhang,Runjie Shen

DOI: https://doi.org/10.18494/sam.2018.1719

IF: 1.2

2018-01-01

Sensors and Materials

Abstract:Partial discharge (PD) usually occurs before the insulation failure of a gas-insulated switchgear (GIS). Early failures in GIS can be detected effectively by monitoring the vibration signal initiated by PD. In this paper, a new type of acoustic-emission (AE) sensor based on a polarization-maintaining and absorption-reducing (PANDA) polarization-maintaining fiber (PMF) is proposed to detect the PD-induced ultrasound information accurately in GIS. Pressure load affects the birefringence of the PMF, leading to variation in light output intensity. Simulation and experimental results indicate that the effective refractive index difference between the x and y polarization modes has a linear relationship with the external pressure. Therefore, pressure variations generated by ultrasound can be obtained by interference demodulation between the x and y polarization modes. The proposed sensor has many advantages such as simple structure, small volume, and strong environmental tolerance. The results of this work provide a new direction for more effective PD detection methods and fault diagnosis approaches.
Distributed Detection and Acoustic Emission Waveform Retrieval of Cable Joint Partial Discharge

Wei-qi Qin,Guo-ming Ma,Jing Hu,Tengjun Guo,Sihan Wang,Hao Liu,Yuan Wang

DOI: https://doi.org/10.1109/tpwrd.2023.3276197

IF: 4.825

2023-08-01

IEEE Transactions on Power Delivery

Abstract:Distributed detection and acoustic emission (AE) waveform retrieval of partial discharge (PD) in power cable joints are significant but challenging tasks. In this paper, we proposed a cable joint PD detection method based on optical fiber distributed acoustic sensing (DAS). Ordinary single-mode optical fiber (SMF) was wound on the outer semiconductive layer to obtain sufficient sensitivity. Coherent optical time domain reflection (COTDR) principle was utilized to detect the phase variation and locate the PDs. The AE waveforms were retrieved by Fourier integration and difference operation. The experimental results indicated that the sensing system had the ability of multi-point monitoring. The PD AE waveforms caused by conductor spike and insulation air gap defects were accurately retrieved.

engineering, electrical & electronic
DFB-FL Applied in the Liquid-Solid Composite Dielectric for Ultra-High Sensitive Partial Discharge Acoustic Emission Detection

Jixian Qiao,Weichao Zhang,Qichao Chen,Xuan Wang,Hong Zhao

DOI: https://doi.org/10.1109/jsen.2021.3096010

IF: 4.3

2021-09-15

IEEE Sensors Journal

Abstract:The traditional fiber optic acoustic emission (AE) sensor, used to detect the partial discharge (PD) in the liquid-solid composite dielectric such as oil-immersed transformers, is not satisfactory in engineering applications due to the limitation of sensitivity and sensor size. This work proposes that the distributed feedback fiber laser (DFB-FL), benefiting from its tiny size and ultra-high sensitivity, is a better choice for PD AE detection. We build the PD AE detection system using erbium-ytterbium co-doped (Er-Yb-co-doped) DFB-FL, with suitable photoelectric components to design the demodulation system and intensity noise of DFB-FL as an index. Noise analysis shows that the average noise amplitude of the system is reduced by 91.67% after digital filtering technology and pump laser power regulation technology. We also use an 80 kVA oil-immersed transformer winding structure to construct a liquid-solid composite dielectric PD AE detection platform. Moreover, experiment results in different pump power show that the DFB-FL PD AE detection system can effectively detect the PD AE signal in the environment with sizeable acoustic impedance. The peak-to-peak value of its response is 31.36 times larger than the background noise and 637% higher than piezoelectric transducer sensors (PZT).

engineering, electrical & electronic,instruments & instrumentation,physics, applied
Fiber Optic MEMS Ultrasonic Sensor and its Application in Partial Discharge Detection

Kang Liu,Ji Shi,Lang Xie,Qian Zhou,Juanjuan Zhang,Yurui Liu

DOI: https://doi.org/10.1088/1742-6596/2433/1/012010

2023-03-03

Journal of Physics: Conference Series

Abstract:In this paper, an optical fiber based ultrasonic sensor was designed and applied to the detection and position of partial discharge (PD). The Fabry-Perot interferometer with a micro-electromechanical system (MEMS) diaphragm has been proven to have high sensitivity, with broadband acoustic frequency response up to 500 kHz and wide directivity. In the PD detection experiment, the minimum detectable pressure (MDP) of the fiber optical MEMS sensor is achieving 0.455μPaHz -1/2 . In addition, four ultrasonic sensors are arranged around the ultrasonic source to conduct localization experiments. The results show that the system has excellent localization performance in x, y and z directions. The favourable acoustic performance of the MEMS sensor provides a high-sensitivity and high signal-to-noise ratio (SNR) detection method for PD detection.
A Fiber Optic Ultrasonic Sensor Using Polarization-maintaining Fiber for Partial Discharge Monitoring

Xuefeng Li,Hexin Cao,Zhiming Chang,Xinyu Zhang,Weishi Zhao,Runjie Shen

DOI: https://doi.org/10.18494/sam.2019.2260

IF: 1.2

2019-01-01

Sensors and Materials

Abstract:Conventional acousto-ultrasonic piezoelectric sensors can be easily interfered in strong electromagnetic environments such as partial discharge (PD). Current research shows that the effective refractive index difference between two orthogonal polarization modes increases differently with external pressure. Light output intensity can be detected by interference demodulation and depolarization from the polarization-maintaining fiber (PMF) between the two orthogonal polarization modes, and then pressure variations can be obtained. In this study, a new type of acousto-ultrasonic sensor based on the principle of polarization interference is designed to detect PD-induced ultrasonic signals. Simulation and experimental results are also discussed by comparing the following two types of PMFs as the sensing unit: polarization-maintaining photonic crystal fiber (PM-PCF) and polarization-maintaining and absorption-reducing (PANDA) fiber. Analysis results have indicated that the PM-PCF has a higher sensitivity towards external pressure, because its birefringence has a linear relationship of 2.02 x 10(-6) RIU/MPa, far beyond 3.01 x 10(-11) RIU/MPa of the PANDA fiber. Then, the function between external pressure and light output intensity can be analyzed. The proposed fiber optic sensor using the PM-PCF as the sensing unit has a higher signal-to-noise ratio (SNR). Therefore, this type of sensor can more easily find the initial failure of equipment.
Fiber optic Fabry–Perot sensor that can amplify ultrasonic wave for an enhanced partial discharge detection

Haoyong Li,Jian Bu,Wenli Li,Jiaming Lv,Xiejun Wang,Kejia Hu,Yiting Yu

DOI: https://doi.org/10.1038/s41598-021-88144-4

IF: 4.6

2021-04-21

Scientific Reports

Abstract:Abstract Ultrasonic wave is a powerful tool for many applications, such as structural health monitoring, medical diagnosis and partial discharges (PDs) detection. The fiber optic extrinsic Fabry–Perot interferometric (EFPI) sensor has become an ideal candidate for detecting weak ultrasonic signals due to its inherent advantages, and each time with a performance enhancement, it can bring great application potential in broadened fields. Herein, an EFPI ultrasonic sensor for PDs detection is proposed. The sensing diaphragm uses a 5-μm-thickness and beam-supported structure to improve the responsive sensitivity of the sensor at the resonant frequency. Furthermore, the ability of the sensor to detect characteristic ultrasonic signal of PDs is further enhanced by assembling a Fresnel-zone-plate (FZP)-based ultrasonic lens with the sensing probe to amplify the ultrasonic wave before it excites the sensing diaphragm. The final testing results show that the originally developed sensor owns the sensitivity of − 19.8 dB re. 1 V/Pa at resonant frequency. While, when the FZP is assembled with the probe, the sensitivity reaches to − 12.4 dB re. 1 V/Pa, and leads to a narrower frequency band, which indicates that the proposed method has a great potential to enhance the detection ability of sensor to characteristic ultrasonic wave of PDs.

multidisciplinary sciences
Finding Ways to Effectively Use Year 12 Achievement Data to Inform Practice in Secondary Schools.

F. Italiano,Gregory Hine

DOI: https://doi.org/10.14221/AJTE.2014V39N5.8

2014-05-01

Abstract:This action research explored how Year 12 achievement data were used by school personnel to inform practice within seven Catholic secondary schools. Deputy Principals of Curriculum from participating schools were interviewed regarding their perceptions of the improvement of Year 12 student achievement outcomes, and their insights into how to strengthen future efforts (or achievements). Three key insights included: Communication of achievement data to key stakeholders in the school community, strategic use of achievement data by teaching staff, and leadership strategies to promote an achievement culture to the students. The findings of this research will serve to improve and strengthen practice at participating schools and to stimulate discussions in other schools about the effective use of achievement data.
SNR Enhancement of Quasi-Distributed Weak Acoustic Signal Detection by Elastomers and MMF Integrated Φ-OTDR.

Jialong Li,Huanhuan Liu,Xingliang Shen,Yihong Xiao,Zhengting Wu,Penglai Guo,Jiaqi Hu,Yutian Liu,Hong Dang,Qizhen Sun,Zhiyong Zhao,Yixin Zhang,Perry Ping Shum

DOI: https://doi.org/10.1364/oe.499806

IF: 3.8

2023-01-01

Optics Express

Abstract:We have proposed and demonstrated a weak acoustic signal detection technology based on phase-sensitive optical time-domain reflectometry (Φ-OTDR). Non-contact acoustic signals transmitting through air gap between the sound source and the receiver are difficult to detect due to fast attenuation. In order to improve the detection ability of non-contact weak acoustic signals, we demonstrate that multi-mode fiber (MMF) is a better solution than single-mode fiber (SMF) benefiting from its larger core and higher Rayleigh backscattering (RBS) capture coefficient. The frequency signal-to-noise ratio (SNR) has been enhanced by 9.26 dB. Then, with the help of 3D printing technology, elastomers have been designed to further enhance the detection ability due to the high-sensitive response to acoustic signals. Compared with the previous reported “I” type elastomer, the location and frequency SNR enhancement caused by our new proposed “n” type elastomer are 8.39 dB and 11.02 dB in SMF based system. The values are further improved to 10.51 dB and 13.38 dB in MMF and “n” type elastomer integrated system. And a phase-pressure sensitivity of -94.62 dB re rad/µPa has been achieved at 2.5 kHz. This non-contact weak acoustic signal detection technique has great application potential in the quasi-distributed partial discharge (PD) detection of smart grid.
Partial discharge detection on power equipment using a magneto-resistive sensor

Yun Chen,Luis Carlos Castro Heredia,Johan J. Smit,Mohamad Ghaffarian Niasar,Robert Ross

DOI: https://doi.org/10.1016/j.ijepes.2023.109270

2023-06-02

Abstract:Partial discharges (PD) detection is an effective diagnostic method to assess the insulation condition of electrical power equipment in the high-voltage laboratory or field tests. This paper presents a non-contacting PD detection method for power equipment. The method is based on an extra high-sensitivity adapted giant magneto-resistive (xMR) sensor that measures the magnetic field produced by the PD currents. Firstly, this paper describes the sensor's relevant principle and signal conditioning circuit. Next, the sensor's typical performance, including the frequency response and time-domain response to calibrator PD pulses, is measured and compared with our previous work. The results indicate that the xMR system's bandwidth is improved to the MHz range. Finally, PD experiments are carried out and compared with measurements using a commercially available high-frequency current transformer (HFCT), which allows for verification of the coherence of the results concerning the PD pulses and phase-resolved PD (PRPD) patterns. The results show that PD in a cross-linked polyethylene (XLPE) cable or a gas-insulated system (GIS) with artificial discharging defects is successfully measured, demonstrating the sensitivity and performance of the xMR system for PD detection.

engineering, electrical & electronic
Flexible Sensor Array Based on Transient Earth Voltage for Online Partial Discharge Monitoring of Cable Termination

Mingshu Zhao,Xiaoyan Cao,Kai Zhou,Yao Fu,Xutao Li,Li Wan

DOI: https://doi.org/10.3390/s20226646

IF: 3.9

2020-11-20

Sensors

Abstract:Cable termination is a weak point in an underground cable system. The transient earth voltage (TEV) method is an effective and nonintrusive method for estimating the insulation condition of cable termination. However, the practical application of TEV detection is mainly focused on switchgears, generators, and transformers with a flat and conductive shell. A flexible sensor array based on the TEV method is presented for online partial discharge (OLPD) monitoring of the cable termination. Each sensing element is designed with a dual-capacitor structure made of flexible polymer material to obtain better and more stable sensitivity. Based on the electromagnetic (EM) wave propagation theory, the partial discharge (PD) propagation model in the cable termination is built to analyze and verify the rationality and validity of the sensor unit. Some influencing factors are discussed regarding the response characteristics of sensors. Finally, the performance of the sensor array is verified by simulations and experiments. Besides, an OLPD monitoring system is introduced. The monitoring system is composed of the on-site monitoring device and the remote monitoring host. The two parts of the system exchange the data through wireless networks using a wireless communication module. The experiment results show that the monitoring device could supply the PD condition monitoring demand for cable termination.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Acoustic emission sensing in fiber Bragg grating based on phase demodulation for material health detection

Xuezhi Zhang,Jiahang Jin,Junfeng Jiang,Chao Wang,Yining Yang,Yuqing Li,Kun Liu,Guanlong Chen,Wenxin Bo,Haonan Sun,Tiegen Liu

DOI: https://doi.org/10.1016/j.optlaseng.2023.107823

IF: 5.666

2023-09-10

Optics and Lasers in Engineering

Abstract:Acoustic emission detection is widely employed in the field of material health monitoring as an important non-destructive testing method. An acoustic emission sensing system based on phase demodulation in fiber Bragg grating is demonstrated in experiment to solve the problems existing in acoustic emission sensor, such as low sensor sensitivity and poor anti-interference capabilities. According to experimental results, the system can effectively detect both continuous and burst acoustic emission signals from 100 kHz to 700 kHz. The signal-to-noise ratio can reach 77 dB and the sensor phase sensitivity is 0.012 rad/με. The dynamic strain resolution of the system is 3.77 nε/√Hz. The system is also able to detect weak burst acoustic emission signals emitted during concrete damage, and the signal-to-noise ratio is 21.5 dB in the acoustic emission sensing in corrosion of reinforcement.

optics
Diaphragm-type Fiber-Optic Interferometric Acoustic Sensor

N Zeng,CZ Shi,DN Wang,M Zhang,YB Liao

DOI: https://doi.org/10.1117/1.1596433

IF: 1.3

2003-01-01

Optical Engineering

Abstract:A diaphragm-type fiber-optic acoustic sensor is developed. In such a sensor, the sound-induced strain is imposed on the fiber on the diaphragm-type sensing element, and can be measured by the use of a Mach-Zehnder interferometer. The diaphragm structure can provide di- rectional response with high sensitivity. The experimental measurement frequency range is from 100 Hz to 5 kHz. The sensitivity and minimum detectable acoustic pressure of the system are 2139 dB re V/mPa and 82 dB re mPa, respectively. © 2003 Society of Photo-Optical Instrumentation Engi- neers. (DOI: 10.1117/1.1596433)
Cholecystectomy using single-incision pediatric endosurgery: technique and initial experience in the first 25 cases.

Cecilia Puga Nougues,C. Harmon,Erik Hansen,K. Georgeson,O. Muensterer

DOI: https://doi.org/10.1089/lap.2009.0405

2010-06-21

Abstract:BACKGROUND Laparoscopic cholecystectomy has become the standard, in most pediatric surgery centers. In the search for a less-invasive procedure, a single-incision laparoscopic approach has been reported in adults and very few children. OBJECTIVE The aim of this study was to present our initial experience of cholecystectomy, using single-incision pediatric endosurgery (SIPES), including the technique, the intraoperative challenges, and the outcome. METHODS All pediatric patients who underwent a SIPES cholecystectomy from March through September 2009 were prospectively evaluated. RESULTS Twenty-five children underwent a SIPES cholecystectomy. The most frequent indications were symptomatic cholelithiasis in 17 patients (68%) and biliary dyskinesia in 5 (20%). Five patients had sickle-cell anemia. The mean operative time was 73 minutes (range, 30-122). Median hospital stay was 1 day. In 17 patients (68%), a percutaneous 2-mm grasper was used to retract the gallbladder over the liver. No complications were noted, and no conversion to an open procedure was required. In 5 patients, additional trocars were added. On follow-up, 3 days to 2 months later, no complications were noted. No patients were readmitted, and there were no wound infections. CONCLUSIONS Cholecystectomy, when using the SIPES approach in children, is a safe, reasonable alternative to conventional laparoscopy, leaving an inconspicuous scar. Whether SIPES offers any further benefit to the patient, besides improved cosmesis, should be evaluated in future studies.
MEMS-on-fiber ultrasonic sensor with two resonant frequencies for partial discharges detection

Haoyong Li,Jiaming Lv,Delin Li,Chaoyu Xiong,Yihong Zhang,Yiting Yu

DOI: https://doi.org/10.1364/OE.391242

2020-06-08

Abstract:A novel fiber optic extrinsic Fabry-Perot interferometric (EFPI) ultrasonic sensor with two resonant frequencies for detecting the partial discharges (PDs) in switchgear is demonstrated. The key sensing element consists of two 5-µm-thickness and beam-supported silicon diaphragms, whose natural frequencies are designed differently to enable the sensor to achieve the resonant responses at two different frequencies, thus obtaining a broadened frequency response. The sensing element is fabricated by employing the microelectromechanical systems (MEMS) technology on a silicon-on-insulator (SOI) wafer. The experimental results show that the sensor possesses two resonant frequencies of 31 kHz and 63 kHz, and obviously, shows a highly sensitive frequency response over a broader range compared with the approach composed of a single sensing diaphragm with only one resonant frequency. The noise-limited minimum detectable ultrasonic pressure (MDUP) reaches 251 µPa/Hz1/2@ 31 kHz and 316 µPa/Hz1/2@ 63 kHz, respectively.

[Conversion of C8 of guanine to a l carbon unit during biosynthesis of riboflavin].

Coherent OTDR Based Ultra-High Sensitive Acoustic Sensor Assisted with Distributed Microstructured Optical Fiber(DMOF) and Hollow Cylinder Transducer

Radio-frequency Detection of Partial Discharge in Power Cable Joints

A High Sensitivity Optical Fiber Interferometer Sensor for Acoustic Emission Detection of Partial Discharge in Power Transformer

Implementation of a Fiber-Wrapped Polymer Mandrel Acoustic Emission Sensor

A Partial Discharge Detection System for XLPE Cable Terminals and Acoustic Wave Sensing Characteristics Based on Fiber Optic Mach-Zehnder Interferometer

Flexible Pb(Zr0.52,Ti0.48)O3 thin film acoustic emission sensor for monitoring partial discharge in power cable

Highly Sensitive Acoustic Emission Sensor Based on Polarization-maintaining and Absorption-reducing Polarization-maintaining Fiber

Distributed Detection and Acoustic Emission Waveform Retrieval of Cable Joint Partial Discharge

DFB-FL Applied in the Liquid-Solid Composite Dielectric for Ultra-High Sensitive Partial Discharge Acoustic Emission Detection

Fiber Optic MEMS Ultrasonic Sensor and its Application in Partial Discharge Detection

A Fiber Optic Ultrasonic Sensor Using Polarization-maintaining Fiber for Partial Discharge Monitoring

Fiber optic Fabry–Perot sensor that can amplify ultrasonic wave for an enhanced partial discharge detection

Finding Ways to Effectively Use Year 12 Achievement Data to Inform Practice in Secondary Schools.

SNR Enhancement of Quasi-Distributed Weak Acoustic Signal Detection by Elastomers and MMF Integrated Φ-OTDR.

Partial discharge detection on power equipment using a magneto-resistive sensor

Flexible Sensor Array Based on Transient Earth Voltage for Online Partial Discharge Monitoring of Cable Termination

Acoustic emission sensing in fiber Bragg grating based on phase demodulation for material health detection

Diaphragm-type Fiber-Optic Interferometric Acoustic Sensor

Cholecystectomy using single-incision pediatric endosurgery: technique and initial experience in the first 25 cases.

MEMS-on-fiber ultrasonic sensor with two resonant frequencies for partial discharges detection