Abstract:Due to the advantages of low cost, easy fabrication, mechanical flexibility, the research on organic solar cells has attracted a lot of attentions in the last decades. Among countless organic materials, the most successful ones are conjugated polymers, which were widely used in bulk heterojunction (BHJ) in conjugation with the fullerene [1]. In view of the fact the interpenetratedphase-separated p-n composites offer more chances for excitons to reach the p-n interfaces, BHJ greatly facilitates the dissociation of photogenerated excitons before decaying to ground state. During exciton dissociation process, the exciton delocalization at an ultra fast timescale has been observed recently, which has considerable effects on the charge generation and device performance. In this work, based on the recent studies [2–4], we established a theoretical model of polymer solar cells (PSCs) incorporating the exciton delocalization process. Through the model, we found the increase of delocalized excitons (compared to the total generated excitons) will significantly improve the short-circuit current, open-circuit voltage, fill factor and power conversion efficiency of PSCs. Particularly, the saturations of fill factor and open-circuit voltage are also observed, and the saturation points depend on the active layer thickness and recombination rate. For instance,the device model of 200nm thickness active layer has the saturated fill factor at 70% delocalization ratio, which is close to the conventional ratio of practical devices. The device configuration studied comprises a BHJ active layer sandwiched between a transparent anode and a metal cathode. Moreover, the active material is a mixture of OC 1 C 10 -PPV, as the donor, and PCBM, as the acceptor [5]. The generation rate of excitons is assumed to be homogeneous. The model proposed involves both the drift-diffusion model for photocarriers (Eq. (1)) and the diffusion and dissociation model for excitons (Eq. (2)). The governing equations are given as follows equation where q is elementary charge, n(p) is the electron (hole) density, and r G , r R are the parametersfor controlling exciton generation and bulk recombination, respectively. E is the internal E-field. µ and D are the mobility and diffusion coefficients. The exciton density is denoted by X diff and k diss is the exciton dissociation rate. The recombination R is taken to be a bimolecular form,with the rate given by Langevin [6], and η s is 0.25 for the singlet excitons. Using the physical parameters given by experiments [5], the nonlinear governing equation sets are solved self-consistently. The excitons are delocalized at an ultra fast timescale to form electron-hole pairs, which is much faster than the photo carrier relaxation time and exciton diffusion time. Consequently, the delocalization process was simulated by directly inserting the delocalization ratio η del into the equations.

Effectiveness of External Electric Field Treatment of Conjugated Polymers in Bulk-Heterojunction Solar Cells

The Role Of Exciton Delocalization In The Performance Of Bulk-Heterojunction Polymer Solar Cells

Ferroelectric field effect of the bulk heterojunction in polymer solar cells

Electric Field-Assisted Self-Organization of Polymer:Fullerene Hybrids on the Photovoltaic Performance

The Influence of Amino Group on PCDTBT-based and P3HT-based Polymer Solar Cells: Hole Trapping Processes

Improvement of Surface Morphology of Thin ?lms and Performance by "electrical Annealing" on Polymer Solar Cells

Interfacial polymer ferroelectric dipole induced electric field effect on the photovoltaic performance of organic solar cells

Bulk heterojunction solar cells based on two kinds of organic polymers and fullerene derivative

[6,6]-Phenyl-c61-butyric Acid 2-((2-(dimethylamino)ethyl)(methyl)amino)-ethyl Ester As an Acceptor and Cathode Interfacial Material in Polymer Solar Cells

Effect of External Magnetic Field on Bulk Heterojunction Polymer Solar Cells

Regulation of organic solar cells performance through external electric field: From charge transfer mechanisms to photovoltaic properties

Thermal Annealing Effect on Ultrafast Charge Transfer in All-Polymer Solar Cells with a Non-Fullerene Acceptor N2200

Transport and spectroscopic studies of the effects of fullerene structure on the efficiency and lifetime of polythiophene-based solar cells

Nanoscale control of the network morphology of high efficiency polymer fullerene solar cells by the use of high material concentration in the liquid phase

Structure Tuning of Crown Ether Grafted Conjugated Polymers as the Electron Transport Layer in Bulk‐Heterojunction Polymer Solar Cells for High Performance

Multiple Functionalities of Polyfluorene Grafted with Metal Ion-Intercalated Crown Ether As an Electron Transport Layer for Bulk-Heterojunction Polymer Solar Cells: Optical Interference, Hole Blocking, Interfacial Dipole, and Electron Conduction.

Investigation of Molecular Dynamics of a PTB7:PCBM Polymer Blend with Quasi-Elastic Neutron Scattering

Comparison of the Morphology Development of Polymer–Fullerene and Polymer–Polymer Solar Cells During Solution‐Shearing Blade Coating

Improved Charge Generation via Ultrafast Effective Hole‐Transfer in All‐Polymer Photovoltaic Blends with Large Highest Occupied Molecular Orbital (HOMO) Energy Offset and Proper Crystal Orientation

Efficiency enhancement in P3HT-based polymer solar cells with a NaYF 4:2% Er3+, 18% Yb3+ up-converter

Tuning the Morphology of Solution-Sheared P3ht:Pcbm Films