Abstract:Anion exchange membrane water electrolysis (AEMWE) is operated in an alkaline environment and has a similar membrane-electrode assembly (MEA) structure to that of proton exchange membrane water electrolysis (PEMWE). The use of non-noble metals as the electrocatalysts and operation at high current densities are inherently possible, so they are expected to be low-cost, high-performance candidates for next-generation water electrolysis systems. Improving the anion conductivity of the AEM and the activity of the non-precious metal catalysts is essential for the practical application of AEMWEs. 1 The non-noble electrocatalysts used in the MEA in this study were Ni 0.8 Co 0.2 O 2 and Ni 0.8 Fe 0.2 O, 3 which have a fused-aggregate network structure, and the electrolyte was a hydrocarbon-based AEM (QPAF-4) 4 , all of which were developed at the University of Yamanashi. The catalyst ink for the anodes was prepared by mixing the Ni 0.8 Co 0.2 O catalyst (University of Yamanashi) with solvent (water/methanol) and QPAF-4 (IEC = 2.0 meq g -1 , University of Yamanashi) binder solution. The anode ink was coated by using pulse-swirl-spray (PSS, Nordson) on the QPAF-4 membranes (IEC = 1.5 meq g -1 ) to make the catalyst-coated membranes (CCMs) with the anode. Catalyst inks for the cathodes was prepared by mixing Ni 0.8 Fe 0.2 O catalyst (University of Yamanashi) or Pt/CB catalyst (TEC10E50E, Tanaka Kikinzoku) with solvent (water/methanol) and QPAF-4 (IEC = 2.0 meq g -1 ) binder solution. The cathode ink was coated by using PSS on the gas diffusion layer (GDL, TGP-H-120, Toray) to make the gas diffusion electrodes (GDEs) for the cathodes. Ni mesh (Bekaert.co.jp) was used for the anode GDLs. The single cell (Figure 1, cell structure developed by Yokohama National University) performances were measured while supplying 1 M KOH at 80 °C to both electrodes. Figure 2 (a) shows the I-V performance of cells using Ni 0.8 Co 0.2 O for the anode and Ni 0.8 Fe 0.2 O or Pt/CB for the cathode. The electrolysis voltage observed for the cell with non-noble metal catalysts on both electrodes was higher than that for the cell with Pt/C on the cathode but was below 2 V at a current density of 1.2 A cm -2 . The value of the onset electrolysis voltage was nearly the same as that of the corresponding rotating disk electrode, 3 suggesting that the intrinsic performance of the cathode catalyst is being realized in the MEA. Increasing the amount of the cathodic catalyst loading scarcely affected the polarization. It is supposed that the fused-aggregate network structure of the Ni 0.8 Fe 0.2 O catalyst contributes to the favorable mass transfer. Figure 2 (b) shows the time dependence of the cell voltage of these cells. The increased loading amount improved the durability of the cathode. It is considered that the increase in the thickness of the cathode catalyst layer alleviated the damage of the GDL fibers to the membrane. These results indicate the possibility of adopting non-precious metal catalysts for both electrodes in AEMWE and thereby significantly reducing the catalyst cost. Acknowledgement This work was partially supported by NEDO of Japan through the AWE-1 project. References 1) A. Lim et al., J. Ind. Eng. Chem ., 76 , 410 (2019). 2) G. Shi et al., ACS Catal ., 12 , 14209 (2022). 3) G. Shi et al., ACS Omega , 8 , 13068 (2023). 4) H. Ono et al., J. Mater. Chem . A , 5 , 24804 (2017). Figure 1

A fuel cell-electrolyzer series device for simultaneous monoethanolamine degradation and hydrogen production: From anode screening and optimization to device investigation

Electrochemical Hydrogenation of Allyl Alcohol Applying PEM Fuel Cell Reatctor

A Study of the Direct Dimethyl Ether Fuel Cell Using Alkaline Anolyte

Development of Cathode Ordered Membrane Electrode Assembly Based on TiO2 Nanowire Array and Ultrasonic Spraying

Photoelectro-catalytic oxidation of monoethanolamine: From the study of electrooxidation mechanism to the development of high-efficient Ni-based photoelectro-catalysts

A cost-effective and highly efficient dissymmetric membrane electrode assembly designed for fuel cells

High‐Efficiency Anion Exchange Membrane Water Electrolysis Employing Non‐Noble Metal Catalysts

Highly stable nanostructured membrane electrode assembly based on Pt/Nb2O5 nanobelts with reduced platinum loading for proton exchange membrane fuel cells

Investigation of membranes-electrodes assemblies in anion exchange membrane fuel cells (AEMFCs): Influence of ionomer ratio in catalyst layers

Value-added formate production from selective ethylene glycol oxidation based on cost-effective self-supported MOF nanosheet arrays

High-performance Membrane Electrode Assembly with Multi-Functional Pt/SnO2–SiO2/C Catalyst for Proton Exchange Membrane Fuel Cell Operated under Low-Humidity Conditions

Dual Oxidation by Hybrid Electrode: Efficiency Enhancement of Direct Hypophosphite Fuel Cell

Accelerated Discovery of Multi-Metallic Nanostructured Catalysts for Anion Exchange Membrane Water Electrolyzers: Oxygen Evolution Reaction

Wastewater treatment, hydrogen and energy recovery using electrochemical advanced oxidation

A Novel Approach to Fabricate Membrane Electrode Assembly by Directly Coating the Nafion Ionomer on Catalyst Layers for Proton-Exchange Membrane Fuel Cells

Interface‐Engineered NiFe/Ni‐S Nanoparticles for Reliable Alkaline Oxygen Production at Industrial Current: A Sulfur Source Confinement Strategy

Enhancing extracellular electron transfer through selective enrichment of Geobacter with Fe@CN-modified carbon-based anode in microbial fuel cells

A Novel Impregnation-Reduction Method Combined with Galvanic Replacement for Fabricating Low Cost MEA with High Performance for PEM Fuel Cells

Assessing the Performance of Continuous-Flow Microbial Fuel Cells and Membrane Electrode Assembly with Electrodeposited Mn Oxide Catalyst

Performance and Durability of Membrane-Electrode Assemblies Using Non-Precious Metal Catalyst and a Hydrocarbon-Based Electrolyte for Anion Exchange Membrane Water Electrolysis

High-Performance MEA Prepared by Direct Deposition of Platinum on the Gas Diffusion Layer Using an Atomic Layer Deposition Technique