Abstract:Anion exchange membrane water electrolysis (AEMWE) is operated in an alkaline environment and has a similar membrane-electrode assembly (MEA) structure to that of proton exchange membrane water electrolysis (PEMWE). The use of non-noble metals as the electrocatalysts and operation at high current densities are inherently possible, so they are expected to be low-cost, high-performance candidates for next-generation water electrolysis systems. Improving the anion conductivity of the AEM and the activity of the non-precious metal catalysts is essential for the practical application of AEMWEs. 1 The non-noble electrocatalysts used in the MEA in this study were Ni 0.8 Co 0.2 O 2 and Ni 0.8 Fe 0.2 O, 3 which have a fused-aggregate network structure, and the electrolyte was a hydrocarbon-based AEM (QPAF-4) 4 , all of which were developed at the University of Yamanashi. The catalyst ink for the anodes was prepared by mixing the Ni 0.8 Co 0.2 O catalyst (University of Yamanashi) with solvent (water/methanol) and QPAF-4 (IEC = 2.0 meq g -1 , University of Yamanashi) binder solution. The anode ink was coated by using pulse-swirl-spray (PSS, Nordson) on the QPAF-4 membranes (IEC = 1.5 meq g -1 ) to make the catalyst-coated membranes (CCMs) with the anode. Catalyst inks for the cathodes was prepared by mixing Ni 0.8 Fe 0.2 O catalyst (University of Yamanashi) or Pt/CB catalyst (TEC10E50E, Tanaka Kikinzoku) with solvent (water/methanol) and QPAF-4 (IEC = 2.0 meq g -1 ) binder solution. The cathode ink was coated by using PSS on the gas diffusion layer (GDL, TGP-H-120, Toray) to make the gas diffusion electrodes (GDEs) for the cathodes. Ni mesh (Bekaert.co.jp) was used for the anode GDLs. The single cell (Figure 1, cell structure developed by Yokohama National University) performances were measured while supplying 1 M KOH at 80 °C to both electrodes. Figure 2 (a) shows the I-V performance of cells using Ni 0.8 Co 0.2 O for the anode and Ni 0.8 Fe 0.2 O or Pt/CB for the cathode. The electrolysis voltage observed for the cell with non-noble metal catalysts on both electrodes was higher than that for the cell with Pt/C on the cathode but was below 2 V at a current density of 1.2 A cm -2 . The value of the onset electrolysis voltage was nearly the same as that of the corresponding rotating disk electrode, 3 suggesting that the intrinsic performance of the cathode catalyst is being realized in the MEA. Increasing the amount of the cathodic catalyst loading scarcely affected the polarization. It is supposed that the fused-aggregate network structure of the Ni 0.8 Fe 0.2 O catalyst contributes to the favorable mass transfer. Figure 2 (b) shows the time dependence of the cell voltage of these cells. The increased loading amount improved the durability of the cathode. It is considered that the increase in the thickness of the cathode catalyst layer alleviated the damage of the GDL fibers to the membrane. These results indicate the possibility of adopting non-precious metal catalysts for both electrodes in AEMWE and thereby significantly reducing the catalyst cost. Acknowledgement This work was partially supported by NEDO of Japan through the AWE-1 project. References 1) A. Lim et al., J. Ind. Eng. Chem ., 76 , 410 (2019). 2) G. Shi et al., ACS Catal ., 12 , 14209 (2022). 3) G. Shi et al., ACS Omega , 8 , 13068 (2023). 4) H. Ono et al., J. Mater. Chem . A , 5 , 24804 (2017). Figure 1

High‐Efficiency Anion Exchange Membrane Water Electrolysis Employing Non‐Noble Metal Catalysts

High-Performing Anion Exchange Membrane Water Electrolysis Using Self-Supported Metal Phosphide Anode Catalysts and an Ether-Free Aromatic Polyelectrolyte

High Performance Anion Exchange Membrane Electrolysis Using Plasma-Sprayed, Non-Precious-Metal Electrodes

An oxide-promoted, self-supported Ni4Mo catalyst for high current density anion exchange membrane water electrolysis

Simultaneous Interfacial Chemistry and Inner Helmholtz Plane Regulation for Superior Alkaline Hydrogen Evolution

Electrodeposited NiFeCoMoW High-Entropy Alloys with Nanoscale Amorphous Structure As Effective Hydrogen Evolution Electrocatalysts

Non-precious high entropy alloys and highly alkali-resistant composite membranes based high performance anion exchange membrane water electrolyzers

NiFeOx and NiFeCoOx Catalysts for Anion Exchange Membrane Water Electrolysis

Commercial anion exchange membrane water electrolyzer stack through non-precious metal electrocatalysts

Development of Ternary Layered Double Hydroxide Oxygen Evolution Reaction Electrocatalyst for Anion Exchange Membrane Water Electrolysis

3D Transition Metal Boride Monolithic Electrode for Industrial Hectoampere-Level Current Anion Exchange Membrane Water Electrolysis

Anion Exchange Ionomers Enable Sustained Pure-Water Electrolysis Using Platinum-Group-Metal-Free Electrocatalysts

Performance and Durability of Membrane-Electrode Assemblies Using Non-Precious Metal Catalyst and a Hydrocarbon-Based Electrolyte for Anion Exchange Membrane Water Electrolysis

Tensile nanostructured hierarchically porous non-precious transition metal-based electrocatalyst for durable anion exchange membrane-based water electrolysis

Boosting Oxygen Evolution Reaction of (Fe,Ni)Ooh via Defect Engineering for Anion Exchange Membrane Water Electrolysis Under Industrial Conditions

(Invited) Current Status and Progress in Anion Exchange Membrane Electrolysis

Highly Active Nanostructured NiCoMo-Based Catalyst for Oxygen Evolution in Anion-Exchange Membrane Water Electrolysis

PGM-Free Catalysts and Electrodes for Anion Exchange Membrane Water Electrolyzers

Nanoporous Surface High‐Entropy Alloys as Highly Efficient Multisite Electrocatalysts for Nonacidic Hydrogen Evolution Reaction

High Performance Anion Exchange Membrane Water Electrolyzer Using Monolayer Nickel-Iron Layered Double Hydroxide As Anode Catalysts

High Performance AEM Water Electrolysis with PGM-Free Electrocatalysts