Abstract:The development of high-power fuel cells could advance the electrification of the transportation sector, including marine and air transport. Liquid-fueled fuel cells are particularly attractive for such applications as they obviate the issue of fuel transportation and storage. Herein, we report a direct methanol hydrogen peroxide fuel cell (DMHPFC) for high-power propulsion applications that delivers 0.8 W cm 2 peak power density by using a pH gradient-enabled microscale bipolar interface (PMBI) to effectively meet the incongruent pH requirements for methanol oxidation/peroxide reduction reactions. DMHPFCs are an important alternative to hydrogen-fed polymer electrode membrane fuel cell (PEMFCs) and anion exchange membrane fuel cells (AEMFCs) due to methanol’s high energy density compared to that of hydrogen and superior kinetics of hydrogen peroxide reduction reaction as compared to Oxygen. A unit volume of Hydrogen gas stored at a pressure of approximately 69 MPa corresponds to volume-specific energy density of roughly 2.1 kWh/l while 39% volume of aqueous methanol and 41% volume of aqueous hydrogen peroxide corresponds to volume-specific energy density of 9.2 kWh/l. So, DMHPFC’s energy density is approximately four times higher than hydrogen fuel cell’s energy density and is comparable to gasoline which contains roughly 9.2 kWh/l of available bond energy. The theoretical potential for Methanol oxidation reaction (MOR) in basic medium is lower than that in an acidic medium (-0.78 V vs. -0.02 V) and the theoretical potential for the Hydrogen peroxide reduction reaction (HPRR) is higher than that for oxygen reduction (1.77 V vs. 1.23 V in acidic medium). This results in the highest theoretically possible cell voltage for cells with alkaline anodes and acidic cathodes. We achieved sustained operation of the DMHPFC with an alkaline anode and an acidic cathode by incorporating our pH-gradient-enabled microscale bipolar interface (PMBI). However, the system exhibits a relatively low Faradaic efficiency of 50% due to the parasitic evolution of O 2 by the decomposition of H 2 O 2 . The O 2 evolution results in a mixed potential at the cathode due to the occurrence of both the HPRR (E 0 = 1.77 V versus standard hydrogen electrode [SHE]) and the oxygen reduction reaction (ORR); (E 0 = 1.23 V versus SHE), lowering the overall cell potential. The O 2 surface coverage reduces the available sites for the HPRR, effectively deactivating the catalyst. Electrocatalysts exhibiting a combination of high HPRR activity and selectivity (by inhibiting H 2 O 2 decomposition, and hence inhibiting ORR) would result in higher faradic efficiency and have been the subject of sustained interest. Here, we examine an alternate reactant-transport engineering approach to improve the overall cell potential and cell performance of the DMHPFC. Our reactant-transport engineering approach has examined the impact of reactant flowrate, flow velocity, residence time, and flow regime (via the Reynolds number ([Re]) on DMHPFC performance. Balancing the competing demands of high residence time to improve Hydrogen peroxide reduction reaction (HPRR) rates with high flowrates to detach adsorbed O 2 , we identify a critical Re and Damkholer number (Da) to efficiently exclude O 2 gas bubbles while maintaining large current densities during the operation of a DMHPFC. Reactant-transport engineering of the cathode flow field architecture and fuel flowrates mitigates parasitic hydrogen peroxide decomposition and oxygen reduction reactions and lessens cathode passivation by oxygen bubbles. DMHPCs fulfilling these criteria provide a power density of >500 mW cm -2 at 1.0 V compared to state-of-the-art polymer electrolyte membrane fuel cells (PEMFCs) that typically operate at 0.75 V. The high peak power density of 800 mW cm -2 at 1.1 V may offer a pathway to reduce fuel cell stack size for propulsion applications. Our work paves the way for such other liquid fuel cells with hydrogen peroxide as the oxidant and enabled with PMBI resulting in significantly improvement in the performance. Figure 1

Dual Oxidation by Hybrid Electrode: Efficiency Enhancement of Direct Hypophosphite Fuel Cell

Construction of Homogeneous Catalyst Layers at Proton Exchange Membrane Fuel Cell Cathodes

A Development of Direct Hydrazine/Hydrogen Peroxide Fuel Cell

Hypophosphites As Eco-Compatible Fuels for Membrane-Free Direct Liquid Fuel Cells

Direct Liquid Fuel Cells by Using Hypophosphites

Introducing Catalyst in Alkaline Membrane for Improved Performance Direct Borohydride Fuel Cells

A Direct Borohydride Fuel Cell Using MnO2-catalyzed Cathode and Hydrogen Storage Alloy Anode

Stable Bimetallene Hydride Boosts Anodic CO Tolerance of Fuel Cells

High-performance H2O2 paper fuel cell boosted via electrolyte toning and radical generation

Bifunctional Electrocatalyst Materials for Improved Cell Reversal Tolerance in PEM Fuel Cell

Theory-Guided Design of Anode Catalysts for Hydrogenous Liquid Fuels

Combining Catalysis And Hydrogen Storage In Direct Borohydride Fuel Cells: Towards More Efficient Energy Utilization

Standalone nickel layered double hydroxide and nickel oxide electrodes as effective anodes in alkaline direct methanol fuel cell

Reactant Transport Engineering Approach at Cathode to High Power Direct Methanol Hydrogen Peroxide Fuel Cell

Stable and High‐performance Flow H2‐O2 Fuel Cells with Coupled Acidic Oxygen Reduction and Alkaline Hydrogen Oxidation Reactions

Multi-functional Anodes Boost the Transient Power and Durability of Proton Exchange Membrane Fuel Cells

A Novel Nanocomposite Catalytic Cathode for Direct Methanol Fuel Cells

Membraneless Hydrogen Peroxide Fuel Cells As a Promising Clean Energy Source

Synergistic sulfur-doped tri-metal phosphide electrocatalyst for efficient hydrazine oxidation in water electrolysis: Toward high-performance hydrogen fuel generation

Phosphotungstic acid modification boosting the cathode methanol tolerance for high-temperature direct methanol fuel cells

Bio-inspired Construction of Advanced Fuel Cell Cathode with Pt Anchored in Ordered Hybrid Polymer Matrix