Abstract:Statement of problem: Previous studies have shown casting methodology to influence the as-cast properties of dental casting alloys. It is important to consider clinically important mechanical properties so that the influence of casting can be clarified. Purpose: The purpose of this study was to evaluate how torch/centrifugal and inductively cast and vacuum-pressure casting machines may affect the castability, microhardness, chemical composition, and microstructure of 2 high noble, 1 noble, and 1 base metal dental casting alloys. Material and methods: Two commonly used methods for casting were selected for comparison: torch/centrifugal casting and inductively heated/ vacuum-pressure casting. One hundred and twenty castability patterns were fabricated and divided into 8 groups. Four groups were torch/centrifugally cast in Olympia (O), Jelenko O (JO), Genesis II (G), and Liberty (L) alloys. Similarly, 4 groups were cast in O, JO, G, and L by an inductively induction/vacuum-pressure casting machine. Each specimen was evaluated for casting completeness to determine a castability value, while porosity was determined by standard x-ray techniques. Each group was metallographically prepared for further evaluation that included chemical composition, Vickers microhardness, and grain analysis of microstructure. Two-way ANOVA was used to determine significant differences among the main effects. Statistically significant effects were examined further with the Tukey HSD procedure for multiple comparisons. Data obtained from the castability experiments were non-normal and the variances were unequal. They were analyzed statistically with the Kruskal-Wallis rank sum test. Significant results were further investigated statistically with the Steel-Dwass method for multiple comparisons (α=.05). Results: The alloy type had a significant effect on surface microhardness (P<.001). In contrast, the technique used for casting did not affect the microhardness of the test specimen (P=.465). Similarly, the interaction between the alloy and casting technique was not significant (P=.119). A high level of castability (98.5% on average) was achieved overall. The frequency of casting failures as a function of alloy type and casting method was determined. Failure was defined as a castability index score of <100%. Three of 28 possible comparisons between alloy and casting combinations were statistically significant. The results suggested that casting technique affects the castability index of alloys. Radiographic analysis detected large porosities in regions near the edge of the castability pattern and infrequently adjacent to noncast segments. All castings acquired traces of elements found in the casting crucibles. The grain size for each dental casting alloy was generally finer for specimens produced by the induction/vacuum-pressure method. The difference was substantial for JO and L. Conclusions: This study demonstrated a relation between casting techniques and some physical properties of metal ceramic casting alloys.

Veterans Administration Cooperative Studies Project No. 147/242. Part VII: The mechanical properties of metal ceramic alloys as cast and after simulated porcelain firing

Age-Hardening Behavior in the Noble Metal Dental Casting Alloys

Comparative evaluation of the effect of simulated porcelain firing cycle on the mechanical properties and microstructure of base metal ceramic alloys

Mechanical properties, fracture surface characterization, and microstructural analysis of six noble dental casting alloys

Effect of PFM Firing Cycles on the Mechanical Properties, Phase Composition, and Microstructure of Nickel-Chromium Alloy

Microstructural, mechanical, ionic release and tarnish resistance characterization of porcelain fused to metal Co-Cr alloys manufactured via casting and three different CAD/CAM techniques

Effect of two heat treatments on mechanical properties of selective-laser-melted Co-Cr metal-ceramic alloys for application in thin removable partial dentures

Bond strengths of porcelain to cobalt-chromium alloys made by casting, milling, and selective laser melting

Cobalt chromium alloys in fixed prosthodontics: Investigations of mechanical properties and microstructure

Effects of Heat Treatment on Metal-Ceramic Combination of Selective-Laser-melted Cobalt-Chromium Alloy.

In vitro element release and biological aspects of base-metal alloys for metal-ceramic applications

Metallurgical and interfacial characterization of PFM Co-Cr dental alloys fabricated via casting, milling or selective laser melting

Effect of heating palladium-silver alloys on ceramic bond strength

The effect of repeated porcelain firings on the marginal fit of millable and conventional casting alloys

Analysis of four dental alloys following torch/centrifugal and induction/ vacuum-pressure casting procedures

Microstructures and Metal-Ceramic Bond Properties of Co-Cr Biomedical Alloys Fabricated by Selective Laser Melting and Casting

Additive Manufacturing of Cobalt-Based Dental Alloys: Analysis of Microstructure and Physicomechanical Properties

Shear bond strength of porcelain to a new millable alloy and a conventional castable alloy

Microstructural and mechanical characterization of six Co-Cr alloys made by conventional casting and selective laser melting

A comparison of 3 alloy surface treatments for resin-bonded prostheses

Evaluation of Metal-Ceramic Bond Characteristics of Three Dental Co-Cr Alloys Prepared with Different Fabrication Techniques