Abstract:Objective: To investigate the accuracy of pure titanium and cobalt-chromium alloy frameworks fabricated using the additive manufacturing (AM) of selective laser melting technology (SLM) for the mandibular implant-supported fixed prostheses and the maxillary removable partial denture (RPD), and to provide a reference for clinical application of SLM pure titanium frameworks. Methods: One edentulous mandibular model with implants and screw fixed abutments at bilateral canines and the first molars was selected and used as the mandibular full arch implant-supported model. At the same time, a Kennedy class Ⅰ maxillary dentition defect model was selected. The digital models were obtained by scanning the dental models, and the metal frameworks of the mandibular full arch implant-supported denture and the maxillary RPD (design model) were designed using the 3 Shape software. Meanwhile, 12 mandibular frameworks in the cobalt-chromium alloy and the pure titanium (6 in each group were treated with heat treatment, while the other 6 were not treated), and 7 maxillary frameworks in the cobalt-chromium alloy and the pure titanium were respectively made by SLM with the improved dual-laser metal printer. The axial direction of the printing powder accumulation was taken as the Z-axis. During the design process, the software (3Shape Dental System 2018) automatically generated the X-axis and Y-axis, X axis was the sagittal axis of the dental model and Y axis was the coronal axis of the dental model. The deviation of the interface center of the abutment of the digital model of the mandibular frameworks from the design model in the X, Y and Z axes was analyzed. As for the trueness of the mandibular framework, the larger the deviation data was, the worse the trueness was. The deviation of the whole maxillary framework and 7 measuring points (palatal plate center point and bilateral occlusal rests, I bars, proximal plates) were analyzed. The fitness of the whole maxillary framework to the design model was expressed by root mean square (RMS) of the deviation data, and the fitness of measuring points was expressed by the mean±standard deviation of the data. The trueness differences of each group before and after heat treatment of the mandibular framework and the fitness of the maxillary framework were compared. Results: The cobalt-chromium alloy frameworks showed lower trueness on the X, Y, Z-axes [(96.3±12.1), (86.3±11.4), (61.2±13.2) μm] than did the pure Ti frameworks [(82.3±11.2), (72.2±10.2), (51.2±11.6) μm] by SLM, and the heat treatment could reduce the discrepancy between the SLM frameworks and STL models, for pure titanium frameworks [(62.4±11.3), (55.2±13.2), (41.3±10.8) μm] and for cobalt-chromium alloy [(84.5±10.5), (72.3±11.2), (54.2±11.6) μm]. For the thin RPD major frameworks, pure titanium had better fitness [(121.3±17.0) μm] than cobalt-chromium alloy [(174.0±18.3) μm] by SLM, and the difference was statistically significant (P<0.05). Conclusions: Pure titanium frameworks fabricated by SLM additive manufacturing technology exhibited better fitness and trueness than did the Co-Cr frameworks after heat treatment respectively, and this satisfied the requirements of implant-supported fixed prostheses and RPD major metal frameworks.

Fabrication of titanium alloy frameworks for complete dentures by selective laser melting

[Pure titanium denture large-span frameworks additively manufactured with selective laser melting]

Adaptation of Removable Partial Denture Frameworks Fabricated by Selective Laser Melting.

Additive Manufacturing of a Removable Partial Prosthesis in Titanium Using Binder Jetting Technology: A Brief Research Report

Castability of a Ti-7.5Mo alloy for fabricating frameworks for removable partial dentures

Comparison between selective laser melted and cast removable partial denture frameworks

Fit and Retention of Cobalt-Chromium Removable Partial Denture Frameworks Fabricated with Selective Laser Melting

Adaptation of cobalt chromium frameworks fabricated by conventional versus selective laser melting techniques: An in vitro and clinical assessment

Methods of Processing Dental Chromium-Cobalt Alloys for Production of Metal Frameworks Faced with Ceramics to Obtain the Best Mechanical Properties

Mechanical properties of cobalt-chromium 3-unit fixed dental prostheses fabricated by casting, milling, and additive manufacturing

Effects of Selective Laser Melting Process Parameters on the Accuracy of the Intaglio Surface of Maxillary Removable Partial Denture Frameworks

Effect of Reinforcement Bar on Trueness of Printed Titanium Kennedy I Removable Partial Denture Frameworks by Selective Laser Melting

Quality assurance thermophysical aspects of highly porous implants with cellular structure obtained by selective laser melting

Accuracy of removable partial denture framework fabricated by casting with a 3D printed pattern and selective laser sintering

Selective Laser Melting Technique of Co-Cr Dental Alloys: A Review of Structure and Properties and Comparative Analysis with Other Available Techniques

CLINICAL AND CYTOLOGICAL EVALUATION OF REMOVABLE PARTIAL DENTURE FABRICATED BY SELECTIVE LASER SINTERING ADDITIVE PROTOTYPING TECHNIQUE

Interface misfit of conventionally milled and novel hybrid full-arch implant-supported titanium frameworks

Investigation of the effect of three sprue designs on the porosity and the completeness of titanium cast removable partial denture frameworks

Evaluation of two printing techniques for maxillary removable partial denture frameworks

Effect of lamination layer thickness and abutment preparation on the fit of Co-Cr multi-unit prostheses fabricated by additive manufacturing: An in vitro study

Titanium clasp fabricated by selective laser melting, CNC milling, and conventional casting: a comparative in vitro study