Abstract:Objective: To investigate the accuracy of pure titanium and cobalt-chromium alloy frameworks fabricated using the additive manufacturing (AM) of selective laser melting technology (SLM) for the mandibular implant-supported fixed prostheses and the maxillary removable partial denture (RPD), and to provide a reference for clinical application of SLM pure titanium frameworks. Methods: One edentulous mandibular model with implants and screw fixed abutments at bilateral canines and the first molars was selected and used as the mandibular full arch implant-supported model. At the same time, a Kennedy class Ⅰ maxillary dentition defect model was selected. The digital models were obtained by scanning the dental models, and the metal frameworks of the mandibular full arch implant-supported denture and the maxillary RPD (design model) were designed using the 3 Shape software. Meanwhile, 12 mandibular frameworks in the cobalt-chromium alloy and the pure titanium (6 in each group were treated with heat treatment, while the other 6 were not treated), and 7 maxillary frameworks in the cobalt-chromium alloy and the pure titanium were respectively made by SLM with the improved dual-laser metal printer. The axial direction of the printing powder accumulation was taken as the Z-axis. During the design process, the software (3Shape Dental System 2018) automatically generated the X-axis and Y-axis, X axis was the sagittal axis of the dental model and Y axis was the coronal axis of the dental model. The deviation of the interface center of the abutment of the digital model of the mandibular frameworks from the design model in the X, Y and Z axes was analyzed. As for the trueness of the mandibular framework, the larger the deviation data was, the worse the trueness was. The deviation of the whole maxillary framework and 7 measuring points (palatal plate center point and bilateral occlusal rests, I bars, proximal plates) were analyzed. The fitness of the whole maxillary framework to the design model was expressed by root mean square (RMS) of the deviation data, and the fitness of measuring points was expressed by the mean±standard deviation of the data. The trueness differences of each group before and after heat treatment of the mandibular framework and the fitness of the maxillary framework were compared. Results: The cobalt-chromium alloy frameworks showed lower trueness on the X, Y, Z-axes [(96.3±12.1), (86.3±11.4), (61.2±13.2) μm] than did the pure Ti frameworks [(82.3±11.2), (72.2±10.2), (51.2±11.6) μm] by SLM, and the heat treatment could reduce the discrepancy between the SLM frameworks and STL models, for pure titanium frameworks [(62.4±11.3), (55.2±13.2), (41.3±10.8) μm] and for cobalt-chromium alloy [(84.5±10.5), (72.3±11.2), (54.2±11.6) μm]. For the thin RPD major frameworks, pure titanium had better fitness [(121.3±17.0) μm] than cobalt-chromium alloy [(174.0±18.3) μm] by SLM, and the difference was statistically significant (P<0.05). Conclusions: Pure titanium frameworks fabricated by SLM additive manufacturing technology exhibited better fitness and trueness than did the Co-Cr frameworks after heat treatment respectively, and this satisfied the requirements of implant-supported fixed prostheses and RPD major metal frameworks.

Effect of Reinforcement Bar on Trueness of Printed Titanium Kennedy I Removable Partial Denture Frameworks by Selective Laser Melting

[Pure titanium denture large-span frameworks additively manufactured with selective laser melting]

Trueness of 3D printed partial denture frameworks: build orientations and support structure density parameters

Fabrication of titanium alloy frameworks for complete dentures by selective laser melting

Accuracy of removable partial denture framework fabricated by casting with a 3D printed pattern and selective laser sintering

Effects of Selective Laser Melting Process Parameters on the Accuracy of the Intaglio Surface of Maxillary Removable Partial Denture Frameworks

Adaptation of Removable Partial Denture Frameworks Fabricated by Selective Laser Melting.

[Comparison of Adaptation and Microstructure of Titanium Upper Complete Denture Base Fabricated by Selecting Laser Melting and Electron Beam Melting].

Additive Manufacturing of a Removable Partial Prosthesis in Titanium Using Binder Jetting Technology: A Brief Research Report

[Effect of Different Support Angles on the Fitness of Removable Partial Denture Framework Fabricated Using Selective Laser Melting Technique].

Evaluation of trueness and precision of removable partial denture metal frameworks manufactured with digital technology and different materials

Accuracy of Mandibular Removable Partial Denture Frameworks Fabricated by 3D Printing and Conventional Techniques

Accuracy of metal 3D printed frameworks for removable partial dentures evaluated by digital superimposition

Effect of finishing and polishing techniques on the fit accuracy and dimensions of conventional and CAD‐CAM removable partial denture frameworks

Investigation of the effect of three sprue designs on the porosity and the completeness of titanium cast removable partial denture frameworks

Evaluation of two printing techniques for maxillary removable partial denture frameworks

Comparison between selective laser melted and cast removable partial denture frameworks

Accuracy of Selective Laser Melted Bar retaining mandibular implant-assisted Overdenture: An In vitro Comparison of Different Impression Materials and Techniques

Castability of a Ti-7.5Mo alloy for fabricating frameworks for removable partial dentures

Feasibility study and material selection for powder-bed fusion process in printing of denture clasps

Fit and Retention of Cobalt-Chromium Removable Partial Denture Frameworks Fabricated with Selective Laser Melting