Abstract:This paper presents analytic study and design considerations of flat wire inductors with distributed gaps for high-power and compact DC-DC Converters. The focus is eddy current loss components within the conductors due to fringing and leakage fluxes. A magnetic equivalent circuit (MEC) is proposed in which eddy currents are modeled by MMFs opposing the primary flux as well as frequency dependent reluctances, which finally leads to a frequency dependent inductance describing the behavior of the inductor at high frequencies. Three formulations for DC resistance depending on the required accuracy are developed. Calculations of the AC resistance based on vector potential obtained from FEM are provided. To provide an insight into the optimized design of such inductors, components of the magnetic flux and induced eddy currents along with sensitivity of the main inductor quantities such as DCR, ESR, loss components and inductance values to the design parameters are investigated. Finally, an inductor is prototyped and experimentally tested to verify the design.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to design and optimize flat - coil inductors suitable for high - current and compact DC - DC converters, especially for the eddy - current loss problems caused by edge effects and leakage magnetic flux in high - frequency applications. Specifically, the main objectives of the paper include: 1. **Analysis and Modeling of Eddy - Current Loss**: Research on the eddy - current loss of flat - coil inductors at high frequencies, especially the losses caused by edge effects and leakage magnetic flux. By introducing the magnetic equivalent circuit (MEC), the eddy current is modeled as a magnetomotive force (MMF) opposite to the main magnetic flux and a frequency - dependent reluctance. 2. **Development of a Frequency - Dependent Inductance Model**: Propose a frequency - dependent inductance model to describe the behavior of the inductor at high frequencies. This model can explain why the inductance decreases at high frequencies. 3. **Calculation of DC Resistance (DCR) and AC Resistance (ACR)**: Develop three DC resistance calculation formulas with different precisions, and provide a calculation method for AC resistance based on the finite element method (FEM). 4. **Optimization of Design Parameters**: Research the distribution of magnetic flux and induced eddy currents, and the sensitivity of the main inductor performance indicators (such as DCR, ESR, loss components, and inductance values) to design parameters, so as to provide guidance for optimized design. 5. **Experimental Verification**: A prototype inductor was fabricated and experimentally tested to verify the effectiveness of the proposed theoretical models and design methods. ### Main Contributions of the Paper - Presented analytical research and design considerations for flat - coil inductors for high - frequency, high - current, and compact DC - DC converters. - Introduced a magnetic equivalent circuit (MEC) including frequency - dependent reluctance, which explains the phenomenon of inductance reduction at high frequencies. - Developed three DC resistance calculation formulas with different precisions. - Calculated the AC resistance using the finite element method (FEM). - Verified the effectiveness of the theoretical model through experiments and demonstrated the practical effects of the optimized design. ### Keywords - Demagnetization - Eddy - current coupler - Finite element method - Interior permanent magnet - Wind turbine Through these studies, the paper provides a theoretical basis and practical tools for inductor design in high - frequency, high - current applications, which helps to further improve the performance and efficiency of power electronic devices.

Analytic Design of Flat-Wire Inductors for High-Current and Compact DC-DC Converters

Multi-objective Design and Optimization of Inductors: A Generalized Software-Driven Approach

Stacked Spiral Inductor Design and Modeling for Fully-Integrated DC-DC Converters

Novel Through-Silicon-Via Inductor-Based On-Chip DC-DC Converter Designs in 3D ICs

High-Density Planar Integrated Magnetics with Two-Sided Merged Inductor Windings and Integrated Cores for Resonant DC/DC Converter

Design Methodology of the Planar Integrated Magnetics Based on Asymmetrical Windings for Resonant DC/DC Converter

Accurate design, simulation and implementation of AC/DC inductors for power electronic converters

Design Methodology of Resonant Inductor in a ZVS Inverter

Modeling and Design of Integrated Inductor and Transformer Considering Superposed Flux Density in On-Board-Charger

External Magnetic Field Minimization for the Integrated Magnetics in Series Resonant Converter

Modelling and Optimisation of Planar Matrix Transformer for High Frequency Regulated LLC Converter

A High Power Density And Efficiency Bi-Directional Dc/Dc Converter For Electric Vehicles

Integrated Super Planar Inductor-Rectifier Design for EV Drive

A Practical Approach for Core Loss Estimation of High-current Gapped Inductors in PWM Converters with a User-friendly Loss Map

A DC Flux Cancellation Design Method for Inverse-Coupled Inductors Used in Interleaved Boost Converters

Modeling, Analysis, and Winding Loss Calculation of Different Litz and Solid Wire on Coupled Inductor in DC–DC Cuk Converter for DCM

Development of an Inductor Design Tool Based on Multi-Objective Optimization and Finite Element Simulation

An accurate calculation method for inductor air gap length in high power DC–DC converters

Modeling of Magnetic Elements Including Losses—Application to Variable Inductor

Inductor Geometry With Improved Energy Density

Two-Dimensional Winding Loss Analytical Model for High-Frequency Multilayer Air-Core Planar Inductor