Low Profile Metamaterial Band-Pass Filter Loaded with 4-Turn Complementary Spiral Resonator for WPT Applications

Rasool Keshavarz,Negin Shariati

2024-08-20

Abstract:In this paper, a very compact and low insertion loss metamaterial band-pass filter (MBPF) at the center frequency of f0=730 MHz is proposed, based on the rectangular-shape 4 turn complementary spiral resonators (4 CSR). The proposed MBPF consists of an interdigital capacitor as a series capacitance in the top layer, leading to improve the stopband performance in the pass band range of 700 to 760 MHz, which makes it suitable for wireless power transfer (WPT) systems by rejecting unwanted signals. In order to validate the performance of the proposed technique, the MBPF is fabricated on the RO-4003 substrate and great agreement is achieved between simulated and measured results. The stop band attenuations of greater than 52 dB and 20 dB are obtained around the 0.8xfcl (lower cutoff frequency) and 1.2xfcu (upper cutoff frequency), respectively.

Systems and Control

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to design a compact, low - insertion - loss band - pass filter (BPF) suitable for wireless power transfer (WPT) systems. Specifically, the authors propose a metamaterial band - pass filter (MBPF) based on a 4 - turn complementary spiral resonator (4 - CSR), aiming at:

1. **Improving compactness**: Design a very small - sized filter (0.03 λg × 0.18 λg) to meet the strict space requirements of modern wireless communication systems and WPT applications.
2. **Reducing insertion loss**: Achieve an insertion loss lower than 0.4 dB to ensure signal transmission efficiency.
3. **Enhancing stop - band performance**: By adding interdigital capacitors as series capacitors within the pass - band range, improve the stop - band performance, especially in the 700 - 760 MHz frequency band, which can effectively suppress unwanted signals.
4. **Optimizing cut - off frequency characteristics**: Make the lower cut - off frequency very steep, so as to better filter out unwanted signals generated by the rectifier.

To verify the proposed technology, the researchers fabricated the MBPF on a RO - 4003 substrate, and a good agreement was achieved between the simulation results and the measurement results. Finally, the filter exhibits excellent performance at a center frequency of 730 MHz, including a lower cut - off frequency attenuation greater than 52 dB and an upper cut - off frequency attenuation greater than 20 dB.

### Summary of Key Formulas

1. **Impedance and Admittance Expressions**:
\[
Z = j\left(\omega L_{Rc} + \frac{1}{\omega C_{Lc}}\right), \quad Y = j\left(\frac{1}{\omega C_{Rc}} + \frac{1}{\omega L_{Lc}} + \frac{1}{\omega C}\right)
\]

2. **Propagation Conditions**:
\[
\cos(\beta l) = 1 + \frac{ZY}{2}
\]
where \( l \) is the physical length of the unit cell and \( \beta \) is the propagation constant of the MBPF.

3. **Cut - off Frequency Calculation**:
\[
f_{cl} = \frac{1}{2\pi} \sqrt{\frac{1}{L_{Lc}(C_{Rc} + \frac{4}{C_{Lc}} + \frac{4}{C})}}, \quad f_{cu} = \frac{1}{2\pi} \sqrt{\frac{1}{C_{Rc} L_{Lc}}}
\]

4. **Transmission Zero Frequency**:
\[
f_z = \frac{1}{2\pi} \sqrt{\frac{1}{L_{Lc}(C + C_{Rc})}}
\]

These formulas are used to describe the working principle of the MBPF and the design and optimization of its key parameters.