Abstract:This study aims at introducing the back stress of anisotropic strain-hardening into the crystal plasticity theory and demonstrating the rationality of this crystal plasticity model to describe the evolution of the subsequent yield surface of polycrystalline aluminum at the mesoscopic scale under complex pre-cyclic loading paths. By using two different scale finite element models, namely a global finite element model (GFEM) as the same size of the thin-walled tube specimen used in the experiments and a 3D cubic polycrystalline aggregate representative volume element (RVE) model, the evolution of the subsequent yield surface for different unloading cases after 30 pre-cycles is further performed by experiments and numerical simulations within a crystal plasticity finite element (CPFE) frame. Results show that the size and shape of the subsequent yield surfaces are extremely sensitive to the chosen offset strain and the pre-cyclic loading direction, which present pronounced anisotropic hardening through a translation and a distortion of the yield surface characterized by the obvious "sharp corner" in the pre-deformation direction and "flat" in the reverse direction by the definition of small offset strain, while the subsequent yield surface exhibits isotropic hardening reflected by the von Mises circle to be distorted into an ellipse by the definition of large offset strain. In addition, the heterogeneous properties of equivalent plastic strain increment are further discussed under different offset strain conditions. Modeling results from this study show that the heterogeneity of plastic deformation decreases as a law of fraction exponential function with the increasing offset strain. The above analysis indicates that anisotropic hardening of the yield surface is correlated with heterogeneous deformation caused by crystal microstructure and crystal slip. The crystal plasticity model based on the above microscopic mechanism can accurately capture the directional hardening features of the yield surface.

Incorporating precipitation-related effects on plastic anisotropy of age-hardenable aluminium alloys into crystal plasticity constitutive models

Acoustic Softening and Residual Hardening in Aluminum: Modeling and Experiments

Modeling the Age-Hardening Process of Aluminum Alloys Containing the Prolate/Oblate Shape Precipitates

Understanding Orientation-Dependent Plasticity in Laser Beam Powder Bed Fusion Stainless Steel Through Crystal Plasticity Modelling

Modeling the effect of precipitation spatial geometry and size distribution on the yield strength of aluminum alloys

A Damage-Effect-involved Phenomenological Crystal Plasticity Model and Computational Methods for Mechanical Responses of FeCrAl Alloys

Crystal Plasticity Finite Element Analyses on the Formability of AA6061 Aluminum Alloy with Different Ageing Treatments

Predicting the in-plane mechanical anisotropy of 7085 aluminum alloys through crystal plasticity simulations and machine learning

Strain Rate Dependent Plasticity Model for Precipitate Hardened Aerospace Aluminum Alloy Produced with Solid-State Additive Manufacturing

Predicting the Precipitation Hardening Response of Particle Strengthened Alloys Hardened by Ordered Precipitates

Modelling the Effect of Room Temperature Storage and Deformation on the Age-hardening Behaviour of Al-Mg-Si alloys

A multi-scale modelling framework for anisotropy prediction in aluminium alloy sheet and its application in the optimisation of the deep-drawing process

Crystal plasticity modeling of non-Schmid yield behavior: from Ni3Al single crystals to Ni-based superalloys

The influence of precipitation on plastic deformation in a high Mg-containing AlMgZn-based crossover alloy: Slip localization and strain hardening

Investigation of Yield Surfaces Evolution for Polycrystalline Aluminum after Pre-Cyclic Loading by Experiment and Crystal Plasticity Simulation

Deformation-Induced Surface Roughening of an Aluminum–Magnesium Alloy: Experimental Characterization and Crystal Plasticity Modeling

A micromechanical study on the effects of precipitation on the mechanical properties of CoCrFeMnNi high entropy alloys with various annealing temperatures

Prediction of Work-Hardening Behavior under Various Loading Paths in 5083-O Aluminum Alloy Sheet Using Crystal Plasticity Models

Investigation and Constitutive Modelling of High Strength 6xxx Series Aluminium Alloy: Precipitation Hardening Responses to FAST (Fast Light Alloys Stamping Technology) and Artificial Ageing

A Method of Crystal Plasticity Finite Element Modelling in BCC, FCC and HCP Metals

Temperature effect on tensile behavior of an interstitial high entropy alloy: Crystal plasticity modeling