Abstract:The 6××× series aluminum alloys Al-Mg-Si-Cu are widely used in the transportation and building industries due to their comprehensive mechanical properties, adequate formability, high corrosion resistance and good weldability. For decades, ultrafine grain structure (UFG) produced by severe plastic deformation (SPD) has been proved to be a promising way in strengthening Al alloy materials. Although this method can guarantee a great improvement in strength, the obtained ductility is always disappointing. Besides, this method has a limitation to fabricate products suitable for practical use. Recently, combining deformation and aging has been proposed to pro-duce high-strength Al alloys. This strategy is very effective in achieving Al alloys with strength-ductility synergy even through conventional producing process, for example, rolling and aging. The strain ratio of deformation is crit-ical in tuning the mechanical properties which could be acquired by the above method. The effect of deformation strain ratio on the age-hardening behaviors and microstructure in Al-Mg-Si-Cu alloy produced by combining cold-rolling and aging are investigated using hardness test, tensile test, EBSD and TEM in this work. The results show that the as-rolled hardness increases gradually with deformation strain ratio. The age-hardening potential declines with the increase of strain ratio, though post-aging could further strengthen the as-rolled alloys. The grains elongate along the rolling direction during deformation and finally have a lamellar structure. Fragmentation and extensive defects like sub-grain boundaries occurs inside the grains. The dislocations become denser inside the alloy with the increase of the deformation ratio. When the deformation ratio is large (above 60%), formation of dislocation tan-gling and sub-grains are observed. Deformation-induced change of the dislocation configuration affects the precipitation significantly. Due to the interaction between solutes precipitation and defects annihilation, the distribution of precipitates undergoes a change from being isolated to a continuous manner.

The influence of precipitation on plastic deformation in a high Mg-containing AlMgZn-based crossover alloy: Slip localization and strain hardening

Concurrent dynamic strain aging and dynamic precipitation evades strength-ductility trade-off in a high Mg-content aluminum crossover alloy

Achieving Microstress-Induced Strengthening and Grain Refinement of Crossover Al–Mg–Zn–Cu Alloy Via Deformation-Induced Precipitation of Multiscale T-phase Mg32(Al Zn Cu)49

Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Alloys under Multi-Directional Severe Strain and Aging

Experimental and Simulation Study for the Influence of Thermal Pre-Deformation on Subsequent Aging Precipitation Kinetics of Al-Zn-Mg-Cu Alloy

Solute cluster evolution during deformation and high strain hardening capability in naturally aged Al–Zn–Mg alloy

Dislocation-induced Β’ Precipitation Behavior and Strength-Ductility Synergistic Enhancement in Mg-Gd-Y-Zr-Ag Alloy

Effects of Mg2Sn precipitation on the age-hardening and deformation behaviour of a Mg-Sn-Al-Zn alloy

Revisiting the Response of Microstructure and Performance to Cold Pre-Strain and the Early Aging Stage in Al-Zn-Mg-Cu Alloy

Influence of Mg content on ageing precipitation behavior of Al-Cu-Li-x alloys

Enhanced Age Hardening Response and Precipitation Evolution of Elastic Stress Aged Mg–Zn Alloys

Effect of Zn/Mg Ratio on Aging Precipitates and Mechanical Property of High Mg Content Al-Mg-Zn Alloys with Sc and Zr Additions

Experimental and Modelling Assessment of Ductility in a Precipitation Hardening AlMgScZr Alloy

Determining the Effect of Microstructure and Heat Treatment on the Mechanical Strengthening Behavior of an Aluminum Alloy Containing Lithium Precipitation Hardened with the δ′ Al3Li Intermetallic Phase

Enhancing Plasticity in BCC Mg-Li-Al Alloys Through Controlled Precipitation at Grain Boundaries

Comparative study on dislocation slip activity of the solid-solution and as-aged Mg-9.8Gd-3.5Y-2.0Zn-0.4Zr (wt%) alloys during ambient temperature quasi-in-situ compression

Quantifying Early-Stage Precipitation Strengthening of Al–Mg–Zn(-Cu) Alloy by Using Particle Size Distribution

The Interactive Effect of Alloy Composition and Pre-Straining on the Precipitation Behavior of Al–Mg–Si–Cu Alloys

EFFECT OF PRE-DEFORMATION ON AGE- HARDENING AND MICROSTRUCTURE IN Al-Mg-Si-Cu ALLOY

Precipitation Behavior and Properties of an Al-8.26Zn-1.95Mg-1.89Cu-0.08Sc-0.17Zr Alloy with Different Dislocation Morphologies Via Pre-Treatment

Achieving Strength-Ductility Synergy in Mg-1.1Gd-0.6Zn-0.3Mn Alloy by Regulating Precipitation Behavior Via Stress Aging Strategy